Stanley FCL-G Manual

Stanley Ikke kategoriseret FCL-G

Læs gratis den danske manual til Stanley FCL-G (3 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 22 personer og har en gennemsnitlig bedømmelse på 3.6 stjerner ud af 11.5 anmeldelser. Har du et spørgsmål om Stanley FCL-G, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

Please read these instructions before operating the product.

Green Beam Self-Levelling Cross Line Laser

FMHT77348

Self-Levelling

FCL-G

P1P2

P1D3

H1H2

2 x L

J1J2

77-348 FCL-G - GB.indd 1 19/12/2014 11:10

Retain all sections of the manual for future reference.

User Safety

WARNING:

• Carefully read the Safety Instructions and Product Manual

before using this product. The person responsible for the

instrument must ensure that all users understand and adhere to

these instructions.

WARNING:

• The following labels are placed on the laser tool to inform you of

the laser class for your convenience and safety. (Text has been

translated here for your convenience)

IEC /EN 60825-1

Complies with 21 CFR 1040.10 and 1040.11 except for deviations

pursuant to Laser Notice No. 50, dated June 2007

CAUTION:

• While the laser tool is in operation, be careful not to expose your

eyes to the emitting laser beam (red light source). Exposure to a

laser beam for an extended time may be hazardous to your eyes.

CAUTION:

• Glasses may be supplied in some of the laser tool kits. These are

NOT certiﬁed safety glasses. These glasses are ONLY used to

enhance the visibility of the beam in brighter environments or at

greater distances from laser source.

Contents

• User Safety

• Contents

• Product Overview

• Keypad, Modes, and LED

• Applications

• Batteries and Power

• Set Up

• Operation

• Accuracy Check and Calibration

• Speciﬁcations

Product Overview

Figure A - Laser Tool

1. Power /Transport Lock

2. Laser Window

3. Keypad

4. 1/4-20 threaded mount

5. 5/8-11 threaded mount

6. Battery Cover with Warning label

7. 4 x AA Batteries

Figure B - Power /Transport Lock

Figure C - Laser Modes

Figure D - Keypad

Figure H - Level Beam Accuracy

Figure I - Horizontal Beam Accuracy

Figure J - Vertical Beam Accuracy

Keypad, Modes, and LED

Switch

Power ON/Pendulum lock off /Self-leveling On

Power OFF/Pendulum lock on

•ToturnthelasertoolON move switch to the unlocked position

•ToturnthelasertoolOFF,moveswitchtothelockedposition

Modes

Laser Beam Available Modes

•AllbeamlinesON

•AllbeamlinesOFF

Self-Leveling (See ﬁgure B)

•Thependulumlockonthelasertoolneedstobeswitchedtotheunlocked/

ON position to enable self-leveling.

Keypad-Pulse key.

Pulse mode ON/OFF key (See ﬁgure D )

Press to activate Pulse mode.(See ﬁgure D # 10 )

Pulse Mode LED/Out-of-Level Indicator Operation (See ﬁgure D # 9 )

LED OFF

1. Pulse Mode is OFF/ Unit is level

LED ON-CONTINUOUS

2. PULSE MODE is ON, and laser unit is within self-leveling range

LED ON-FLASHING

3. Laser unit is OUT OF LEVEL.

Keypad-Battery key

Battery level indicator key (See ﬁgure D )

Battery Life LED (See ﬁgure D # 8)

LED OFF

1. Battery life >25%

LED ON-CONTINUOUS

2. Battery life < 25%

Applications

Plumb Transfer

•Usingtheverticallaserbeam,establishaverticalreferenceplane.

•Positionthedesiredobject(s)untiltheyarealignedwiththeverticalreference

planetoensureobject(s)areplumb.

Level Transfer

•Usingthehorizontallaserbeam,establishahorizontalreferenceplane.

•Positionthedesiredobject(s)untiltheyarealignedwiththehorizontal

referenceplanetoensureobject(s)arelevel.

Square

• Using the vertical and horizontal laser beams, establish a point where the two

beams cross.

•Positionthedesiredobject(s)untiltheyarealignedwithboththeverticaland

horizontallaserbeamstoensureobjects(s)aresquare.

Batteries and Power

Battery Installation / Removal (See ﬁgure B)

Laser Tool

• Turn laser tool to battery door and open.

• Install / Remove batteries. Orient batteries correctly when placing into

battery compartment.

• Close battery door. Be sure that the door has been closed securely.

WARNING:

• Pay close attention to the battery holder’s (+) and (-) markings

for proper battery insertion. Batteries must be of same type and

capacity. Do not use a combination of batteries with different

capacities remaining.

Set Up

Laser Tool

• Place laser tool on a ﬂat, stable surface.

• To power ON and activate the auto leveling feature move the pendulum

/ transport lock to the unlocked position. The laser tool must then be

positioned in its upright position on a surface that is within the speciﬁed

compensation range.

Mounting on Accessories

• Position accessory in a place where it will not be easily disturbed and

near the central location of the area to be measured.

• Setuptheaccessoryasrequired.Adjustpositioningtobesureaccessory

base is near horizontal (within laser tools compensation range).

• Mount the laser tool to the accessory using the appropriate fastening

method to be used with such accessory / laser tool combination.

CAUTION:

• Do not leave the laser tool unattended on an accessory without

fully tightening the fastening screw. Failing to do so may lead to

the laser tool falling and sustaining possible damage.

NOTE:

• It is best practice to always support laser tool with one hand when placing or

removing laser tool from an accessory.

• If positioning over a target, partially tighten the fastener, align laser tool,

and then fully tighten.

Operation

NOTE:

• Before operating the laser tool always be sure to check the laser tool for

accuracy.

• Laser tool will indicate when it is out of compensation range. Reference LED

Descriptions. Reposition laser tool to be closer to level.

• When not in use, please be sure to power OFF the laser tool by placeing the

pendulum lock in the locked position.

Power

• To turn the laser ON move the pendulum / transport lock to the unlocked

position.

• To turn the laser OFF, move the pendulum / transport lock to the locked

position.

Modes

OFF/ Locked (See ﬁgures B )

• The laser will be OFF and the pendulum locked.

ON/ Self-Leveling (See ﬁgures B )

• The pendulum lock on the laser tool will be positioned in the unlocked

/self-leveling position when the laser is turned ON

•

Accuracy Check and Calibration

NOTE:

• The laser tools are sealed and calibrated at the factory to the accuracies

speciﬁed.

• It is recommended to perform a calibration check prior to its ﬁrst use and

then periodically during future use.

• The laser tool should be checked regularly to ensure its accuracies,

especially for precise layouts.

• When performing the accuracy checks, use the largest area / distance

possible, closest to the operating distance. The greater the area / distance,

the easier to measure the accuracy of the laser.

• The lock must be in the unlocked position to allow the laser tool to self-level

before checking the accuracy.

Level Beam Accuracy (See ﬁgure H)

• H1 Place laser tool as shown with laser ON. Mark point P 1

at cross.

• H2 Rotate laser tool 180° and mark point P 2

at cross.

• H3 Move laser tool close to wall and mark point P 3

at cross.

• H4 Rotate laser tool 180° and mark point P 4

at cross.

• H5 Measure the vertical distance between P1 and P3 to get D3 and the

vertical distance between P2

and P 4

to get D4 .

• Calculate the maximum offset distance and compare to the difference of

D3 and D4

asshownintheequation.

• If the sum is not less than or equal to the calculated maximum

offset distance the tool must be returned to your Stanley

Distributor for calibration.

Maximum Offset Distance:

= 0,6 mm

m x (D 1 m - (2 x D2 m))

Maximum

= 0,007 in

ft x (D

1 ft - (2 x D 2

ft))

Compare : (See ﬁgure H

D3 - D4

≤ ± Maximum

Example:

• D1

= 10 m, D 2 = 0,5 m

• D3 = 0,5 mm

• D4 = - 1,0 mm

• 0,6 mm

m x (10 m - (2 x 0,5 m) = 5.4 mm

(maximum offset distance)

• (0,5 mm) - (- 1,0 mm) = 1,5 mm

• 1,5 mm ≤ 5.4 mm

(TRUE, tool is within calibration)

77-348 FCL-G - GB.indd 2 19/12/2014 11:10

Produkt Specifikationer

Mærke:	Stanley
Kategori:	Ikke kategoriseret
Model:	FCL-G

Har du brug for hjælp?

Hvis du har brug for hjælp til Stanley FCL-G stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Stanley Manualer

Stanley JS900CS Manual

3 August 2025

Stanley STMT81255-1 Manual

17 Juli 2025

Stanley STST83400 Manual

8 Juli 2025

Stanley SXAE00014 Manual

28 Marts 2025

19 September 2024

8 September 2024

6 September 2024

6 September 2024

Stanley SHR263 Manual

6 September 2024

Stanley STWB8902P Manual

31 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Scotsman Prodigy Plus NH0422 Manual

13 Oktober 2025

Chief FCA800HS Manual

13 Oktober 2025

Chief OLCM1U Manual

13 Oktober 2025

IPEGA PG-P5V002 Manual

13 Oktober 2025

IPEGA PG-P5013 Manual

13 Oktober 2025

IPEGA PG-SW2210 Manual

13 Oktober 2025

IPEGA PG-P5042 Manual

13 Oktober 2025

Scotsman Prodigy Plus NH0922 Manual

13 Oktober 2025

Anybus EtherMIRROR Manual

13 Oktober 2025

IPEGA PG-SW2019 Manual

13 Oktober 2025