Stanley S200 Manual

Stanley Ikke kategoriseret S200

Læs gratis den danske manual til Stanley S200 (50 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 41 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 21 anmeldelser. Har du et spørgsmål om Stanley S200, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/50

REV A 08STHT77406

S200

2 3 6 7

≤3 sec

4 5

1 77406

Stanley Stud Sensor 200

The Stud Sensor 200 uses electronic signals to locate the center of

studs, joists or live AC wires through drywall or other common building

materials. Once the center of a stud has been detected in one pass

across the surface, the Stud Sensor 200 gives a visual display and

sounds an audible tone. A marking channel allows you to easily note

the stud center and edges on the wall.

Note: Read all instructions prior to operating the Stud Sensor 200 and

DO NOT remove any labels from the tool.

WARNING:

Protect Your Eyes, Wear Safety Goggles. Usage

Detecting Wood / Metal Studs

2 Hold the Stud Sensor 200 ﬂ at

against the surface, making ﬁ rm

contact.

3 Press in and hold the activation

button. A series of tones will

sound.

Note: The unit cannot be moved

before calibration is complete.

6 / 7 When it detects the stud

center, the “Center” icon will

appear on the LCD and an audible

tone will sound. Use the marking

channel located at the top of the

unit to mark the stud center.

OPERATING INSTRUCTIONS

Battery

1 Open door on back of unit and connect a 9 volt

battery (not included) to clip. Put battery back into

case and close back battery door.

Note: Recommend to replace a new 9 volt

battery when low battery - “Low Battery” will

appear on the LCD.

10 If all segments of the LCD ﬂ ash on and off

when the activation button is pressed, move the

Stud Sensor 200 to a different location and try

again. Releasing the activation button will turn

off the sensor.

Note: While calibrating, the Stud Sensor 200

must not be placed directly over a stud, dense

material such as metal, or over a wet or newly

painted area, or it will not properly calibrate.

8 Slide the Stud Sensor 200 slowly across the surface in a straight

line. As it detects a stud, the unit will display the relative position

of the stud on the screen.

• Marking Channel

• Live Wire Warning LED

• LCD Display

• Activation Button

• Live Wire Detected

• Low Battery Indicator

• Self-Calibration Complete

• Stud Location Graphic

4 When the unit is calibrated the

“Ready” icon will appear on the

LCD.

5 Keep holding the activation

button during all of the following

procedures.

Note: Once the Activation button

is released, the unit shuts off.

www.STANLEYTOOLS.com

701 East Joppa Road

Towson, Maryland 21286

2 77406

Detecting Live AC Wires

9 The live wire red LED will illuminate, the “AC”

icon will appear on the LCD, and the Stud Sensor

200 sounds an audible tone, warning when in the

proximity (typically within 4” to 18” along the

surface) from a live wire.

Note: Static electrical charges that can develop on drywall and

other surfaces will spread the voltage detection area many inches

on each side of the actual electrical wire. To aid in locating the

wire position, scan holding the unit ½” away from the wall surface

or place your other hand on the surface approximately 12” from

sensor.

Warning: Shielded wires or wires in metal conduits, casings,

metallized walls or thick, dense walls will not be detected. Always

turn off AC power when working near wiring.

Cautions on Operating

You should always use caution when nailing, cutting and

drilling in walls, ceilings and ﬂ oor that may contain wiring

and pipes near the surface. Always remember that studs or

joists are normally spaced 16 inches or 24 inches apart and are

1½ inches in width. To avoid surprises, be aware that anything closer

together or of a different width may not be a stud.

OPERATING TIPS

The Stud Sensor 200 is designed for use only on interior surfaces.

Prevent Interference

To ensure best performance from the Stud Sensor 200, keep your

free hand at least 6 inches away from the unit and wall surface

while testing or scanning surfaces.

Conventional Construction

Doors and windows are commonly constructed with additional studs

and headers for added stability. The Stud Sensor 200 detects the

edge of these double studs and solid headers as a single, wide stud.

Surface Differences

The Stud Sensor 200 will scan through common building materials,

Including:

• Gypsum drywall

• Plywood sheathing

• Hardwood ﬂ oors

• Linoleum over wood

• Wallpaper

The scanner cannot scan through:

• Carpeting

• Foil faced materials

• Ceramic tile

• Cement or concrete

• Metal & plaster walls

Wallpaper

There will be no difference in the function of the Stud Sensor 200

on surfaces covered with wallpaper or fabric unless the coverings

used contain metallic foil or ﬁ bers.

Ceilings

When dealing with a rough surface such as a sprayed ceiling,

utilize a piece of cardboard when scanning the surface. Run

through the calibration technique described earlier with the piece

of cardboard too, to assure best performance of the unit. Also, it is

particularly important in this application to remember to keep your

free hand away from the unit.

Note: The thickness, density and moisture content of the surface

material will affect the sensing depth.

IMPORTANT SAFETY NOTICE

Insure proper detection of live wires. Always hold the Stud Sensor

200 in the handle area only. Grasp between ﬁ ngers and thumb while

making contact with your palm.

SPECIFICATIONS

(At 35-55% relative humidity)

Battery 9 volt (not included)

Depth Range

Wood or

Metal Studs

Up to 3/4” (19 mm)

through drywall

Live AC Wires

(120 volts AC)

Up to 2” (50 mm)

through drywall

Accuracy - Stud Center

Wood ±1/8” (3 mm)

Metal ±1/4” (6 mm)

Operating

Temperature +32°F to +120°F (-0°C to +49°C)

Surface

Temperature -4°F to +150°F (-20°C to +66°C)

WARRANTY

Stanley Tools warrants the Stud Sensor 200 against defects in

material and workmanship for one year from the date of purchase.

Stanley’s liability under this warranty is limited the replacement

of the unit. Any attempt to repair the product by other than factory

authorized personnel will void this warranty. Calibration, batteries

and maintenance are the responsibility of the user. Where permitted

by law, Stanley is not responsible for incidental or consequential

damages. Agents of Stanley cannot change this warranty. Stanley is

not responsible for damage resulting from wear, abuse or alteration of

this product. The user is expected to follow ALL operating instructions.

This warranty may provide you with additional rights that vary by

state, province or nation.

Produkt Specifikationer

Mærke:	Stanley
Kategori:	Ikke kategoriseret
Model:	S200

Har du brug for hjælp?

Hvis du har brug for hjælp til Stanley S200 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Stanley Manualer

Stanley JS900CS Manual

3 August 2025

Stanley STMT81255-1 Manual

17 Juli 2025

Stanley STST83400 Manual

8 Juli 2025

Stanley SXAE00014 Manual

28 Marts 2025

19 September 2024

8 September 2024

6 September 2024

6 September 2024

Stanley SHR263 Manual

6 September 2024

Stanley STWB8902P Manual

31 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

DeWalt DXV38PRO Manual

3 September 2025

Thermador DC4889W Manual

3 September 2025

Wolfcraft 6902506 Manual

3 September 2025

Epson EcoTank L3201 Manual

3 September 2025

Arktic 232194 Manual

3 September 2025

DeWalt DXV53PRO Manual

3 September 2025

Turbo Air PRO-77H Manual

3 September 2025

PureLink PureTools PT-MA-HD44M Manual

3 September 2025

Speco Technologies O4VBW2 Manual

3 September 2025

RYOBI One+ PBLCK02K Manual

3 September 2025