StarTech.com C2-ETHERNET-EXTENDER Manual

StarTech.com Wifi repeater C2-ETHERNET-EXTENDER

Læs gratis den danske manual til StarTech.com C2-ETHERNET-EXTENDER (3 sider) i kategorien Wifi repeater. Denne vejledning er vurderet som hjælpsom af 49 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 25 anmeldelser. Har du et spørgsmål om StarTech.com C2-ETHERNET-EXTENDER, eller vil du spørge andre brugere om produktet?

Side 1/3
Quick-Start Guide
To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.
Manual Revision: April 11, 2024
Product ID
C2-ETHERNET-EXTENDER
Front View
Component Function
1ON/OFF Position Sets a specied orDIP Switch ON OFF
2DIP Switches
Select the desired change for (1) Link Fault Pass-Through
(LFPT) (2) Link Speed (3) Local/Remote , , or mode
Note: Keep the DIP Switch 4 in the OFF position at all times to
prevent undesired behavior.
LFPT Note: If a link between two units is lost, one unit may
continue to send packets assuming the link is up, potentially
leading to data loss. LFPT minimizes this risk by forcing a link
down state upon link failure.
3LAN Port
Connects the unit to the orLocal Local Network Host
Device/Computer RJ45 UTP Cablevia
Connects the unit to a orRemote Remote Network
IP-Based Device RJ45 UTP Cablevia
4LED Indicators Indicate the status of , , , Local/Remote Power Link Status
Link Speed LFPT, and
5LINE Port Connects the and units to each other using Local Remote
RJ45 RJ11UTP Cable or
6DC Power Port
(At the Back)
Connect to a using the included Power Source Power
Adapter
Recommended 12V and 1A
Type M barrel plug: Ø 5.5x2.1x9.5mm
10/100 Base-TX Ethernet Extender Kit - Extend up to 2,624ft (800m)
LED Indicators
LED Color ON OFF
Local Green Local Mode is ON Auto Mode
PWR Green Unit is receiving power Unit is not receiving power
LAN Link Green LAN Link Up LAN Link is Down
100M Green Local to Remote Link is
operating at 100Mbps
Local to Remote unit Link
is operating at 10Mbps or
is Down
LFPT Green
LFPT function is ON,
and a LAN Link Fault has
occurred
LFPT function is OFF or
LFPT function is ON, and
no LAN Link Fault has
occurred
10M Green Local to Remote Link is
operating at 10Mbps
Local to Remote unit Link
is operating at 100Mbps or
is Down
Package Contents
Ethernet Extender x 2
Power Adapter x 2
Mounting Bracket x 2
Mounting Screws x 4
Quick-Start Guide x 1
Requirements
For the latest requirements, please visit www.startech.com/C2-ETHERNET-EXTENDER
RJ45 terminated UTP/STP Cat5e (or better) Ethernet cable (sold separately)
Phillips head screwdriver
1
3
2
54
*Product may vary from image
Note: If the DIP Switches need to be adjusted after the initial setup, both units must be
Powered O before changing the DIP Switch settings.
Install the Ethernet Extender Kit
1. Adjust the according to the needs of the setup.DIP Switches
2. Position the units in each of the deployment locations, and .Local Remote
3. Plug in an from the on the unit to an RJ45 Patch Cable LAN Port Local Extender
Ethernet Port Local Network Host Device/Computer on a or a .
4. Plug in an from the on the unit to an RJ45 Patch Cable LAN Port Remote Extender
Ethernet Port Remote Network IP-Based Deviceon a or .
5. Plug in a terminated or from the on the RJ45 RJ11 UTP Cable Line PortLocal
Extender Line Port Remote Extender unit to the on the unit.
6. Connect the included to the on the andPower Adapter DC Power Port Local
Remote units.
Mounting the Local and Remote Units
Warning!
The mounting hardware included with this product may not be adequate for some
wall structures. If lacking the necessary expertise to wall mount this product, contact
a construction professional to install the mounting hardware or to provide specic
mounting instructions for the wall structure.
Note: Use one of the Wall Mount Brackets as a template to mark the Holes to be
drilled on the Wall or Mounting Surface.
1. Align the holes in the with the holes on the of the Wall Mount Brackets Bottom
Local Remote or units.
2. Insert the Mounting (x 2) through the and into the Screws Wall Mount Bracket
Local Remote or unit. (Figure 1)
Figure 1
3. Tighten the using a . Mounting Screws Phillips Head Screwdriver
4. Use the (x 2) on the to attach the orKey Holes Wall Mount Brackets Local Remote
unit to the (x 2) on the or . Screws Wall Mounting Surface
5. Repeat to with the remaining unit. Steps 1 4
Installation
Extension Distance and Link Speed
Extension Distance ft (m)
Cat5e or Cat6 UTP Link speed (Mbps)
2 Pairs 1 Pair
328ft (100m) 100Mbps 100Mbps
656.1ft (200m) 100Mbps 100Mbps
984.2ft (300m) 100Mbps 100Mbps
1312.3 (400m) 100Mbps 10Mbps
1640.4 (500m) 100Mbps 10Mbps
2296.5ft (600m) 100Mbps 10Mbps
2296.5ft (700m) 10Mbps 10Mbps
2624.6ft (800m) 10Mbps 10Mbps
Note: Either Unit can be the Local or Remote Unit.
If the Link Speed is set to 10Mbps it will limit the speed regardless of distance and
number of pairs in the UTP Cable used.
DIP Switches
DIP Switch ON OFF
1 - LFPT
When the Remote Unit's
Network Link Down is the
Network Link Local of the unit
will be Forced Down
Disables LFPT
2 - Link Speed Forces the to Link Speed
10Mbps
Auto-selects the Link Speed
between 10 or 100Mbps
depending on the Extension
Distance Pairsand number of
of usedUTP Cable
3 - Local/Remote
Forces either of the units to
Local Mode
Note: Only one unit must be
set to Local mode
Auto-selects the and Local
Remote unit (factory default)
4 - No Function -
Leave to Permanently OFF
connect the to DIP Switch
ground
Quick-Start Guide


Produkt Specifikationer

Mærke: StarTech.com
Kategori: Wifi repeater
Model: C2-ETHERNET-EXTENDER

Har du brug for hjælp?

Hvis du har brug for hjælp til StarTech.com C2-ETHERNET-EXTENDER stil et spørgsmål nedenfor, og andre brugere vil svare dig