Studio Titan 01-398 Manual

Studio Titan Ikke kategoriseret 01-398

Læs gratis den danske manual til Studio Titan 01-398 (10 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 16 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 8.5 anmeldelser. Har du et spørgsmål om Studio Titan 01-398, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/10

STA 01-398 Lowering Plate

CAUTION: Use leather work gloves and safety glasses when handling the box, when

opening the box and when assembling the product.

HAZARD: Strapping is under tension and can jump when cut. Strapping and Buckles,

Protective Edging, Plastic Walls, Plastic Caps and Product Components and parts should be

handled with care. Work slowly, use extra caution to avoid any sharp edges.

Additional Tools may be Required: The essential tools are included. The following tools

are recommended to be on site: Box Cutter, Scissors, Screw Driver, Plyers or Adjustable

wrench, Metric Hex / Allen Key set

STA 01-398 Lowering Plate

STA 01 398 Lowering Plate - -

Assembly

Refer to Diagram A. Remove the end cap of the STA 01 398 circular arm tube by turning it counter clockwise. - -

Locate and Loosen the hex head screws with supplied hex key, in the rectangular arm. Insert the circular arm

tube into the hole of the rectangular arm and tighten the hex head screw clockwise with supplied hex key. Re-

place the end cap of the STA 01 398 circular arm tube by turning it clockwise. The finished assembly will look - -

like Diagram B.

The STA 01 398 Lowering Plate can be mounted onto the camera stands horizontal arm in the following posi-- -

tions: 0 degrees pointing up, 60 degrees pointing forward, 120 degrees pointing forward and downward, 180

degrees pointing down, 240 degrees pointing backward and downward, 300 degrees pointing backward and

upward. The circular tube can be mounted on either side of the clamp plate pointing toward the center column

or away from the center column.

The Camera Head Mount Plate can be re positioned using the hand lever. It can be re positioned anywhere - -

from 0 360 degrees around the circular arm. -

*CAUTION:

When using the STA 01 398 Lowering Plate the load capacity [camera, etc.] must be reduced.- -

The nominal load capacity must be reduced by using the following formula:

(STA supplied published stand load capacity / (300mm + Length of originally supplied STA Horizontal Arm/Bar

in mm )/ (Length of originally supplied STA Horizontal Arm/Bar in mm)) = new full extension load capacity

( STA C01 360= 10kg ) / (300mm+700mm / 700mm ) = 7 Kg / 15.4 lbs- -

Diagram A Diagram B

Produkt Specifikationer

Mærke:	Studio Titan
Kategori:	Ikke kategoriseret
Model:	01-398

Har du brug for hjælp?

Hvis du har brug for hjælp til Studio Titan 01-398 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Studio Titan Manualer

Studio Titan 01-398 Manual

10 December 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

MRP Ribbon Manual

3 Juli 2025

Cougar STC 600 Manual

3 Juli 2025

Schneider GVAPR54 Manual

3 Juli 2025

Rowenta X-PERT 7.60 RH6A21 Manual

3 Juli 2025

Turtle Beach Atom Manual

3 Juli 2025

Schneider GV2MCK04 Manual

3 Juli 2025

Rowenta Sprinto Silence SO2040 Manual

3 Juli 2025

Chauvin Arnoux C177A Manual

3 Juli 2025

Aiper Pilot V2 Manual

3 Juli 2025

Rowenta X-Pert 7.60 RH6A31 Manual

3 Juli 2025