System Sensor BEAM-MMK Manual

System Sensor Detektor BEAM-MMK

Læs gratis den danske manual til System Sensor BEAM-MMK (2 sider) i kategorien Detektor. Denne vejledning er vurderet som hjælpsom af 35 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 18 anmeldelser. Har du et spørgsmål om System Sensor BEAM-MMK, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

1 I56-2358-004

06-10

INSTALLATION AND MAINTENANCE INSTRUCTIONS

BEAMMMK

Multi-mounting Kit for use with

Reective Projected Beam Smoke Detectors

3825 Ohio Avenue, St. Charles, Illinois 60174

800/736-7672, FAX: 630/377-6495

www.systemsensor.com

MOUNTING AND WIRING INSTRUCTIONS:

TRANSMITTER/RECEIVER

The BEAMSMK accessory must be used with the transmitter/receiver to pro-

vide wiring entry. Refer to Figures 2 through 4 for this step.

1. Read the installation instructions of the beam detector to determine the

appropriate size and number of wires to be used.

2. Drill the appropriate holes for the flexible conduit using the drill centers

provided on either the sides or the back of the surface mount base. See

Figure 2 for details. Note that the top of the surface mount base contains

mounting bosses for the “L” brackets used in the next step. Conduit sizes

of 1/2″ or 3/4″ are acceptable.

3. Assemble the “L” brackets to the surface mount base using the two #10-

24 × 5/8″ screws and two #10 split-lock washers provided. See Figure 3 for

details. The screws should be fully tightened.

4. Assemble the “U” bracket to the “L” brackets using the two #10-24 ×

1/2″ screws and fender washers provided. See Figure 3 for details. The

“U” bracket should be assembled to the “L” brackets so that the words

“DO NOT PAINT” appear in the front of the assembly. Tighten the screws

until almost snug. The assembly should tilt freely in either direction. The

screws will be fully tightened later when the alignment is performed.

5. Insert the flange of the “U” bracket into the keyed hole of the wall or ceil-

ing mount bracket. Slide the bracket forward into position. The surface

mount base should now hang from the bracket.

6. Insert the correct screw and washer combination (either wall or ceil-

ing mount) through the slot and into the hole of the mounting bracket

flange. Tighten the screw until almost snug. The assembly should still

Notice: This manual should be left with the owner/user of this equipment.

GENERAL DESCRIPTION

The BEAMMMK allows reflected beam detectors and reflectors to be mounted

to either a vertical wall or the ceiling. The kit allows for additional alignment

range in cases where the detector and reflector cannot be mounted within

10° of each other. The kit includes the hardware necessary to mount either

a single transmitter/receiver unit or a single reflector. (To mount the trans-

mitter/receiver the surface mount kit, BEAMSMK, must also be used). If the

transmitter/receiver and the reflector require additional alignment range two

kits are required. The kit is not compatible with the long-range reflector kit

(BEAMLRK).

The kit includes the following parts:

Qty. Description

1 Ceiling mount bracket inside

1 Ceiling mount bracket outside

1 Wall mount bracket

1 “U” bracket

2 “L” bracket

1 Horizontal adjustment screw (ceiling) #10-24 × 2 1

4″

1 Horizontal adjustment screw (wall) #10-24 × 13/

8″

2 Allen screw #10-24 × 1

/2″

2 Allen screw #10-24 × 5

/8″

2 Fender washer plastic

2 Fender washer metal

2 Washer plastic #10

2 Washer metal #10

2 Washer metal split-lock #10

2 Hex nut #10-24

1 Allen wrench

MOUNTING BRACKETS

Install a ceiling or wall bracket so that when mounted, the transmitter/re-

ceiver and the reflector will have a clear line of sight between them.

The ceiling bracket is composed of two parts that should be assembled with

the inside part between the ceiling and the outside part as shown in Figure 1.

The brackets should be mounted so that the slot in the front of each bracket

is facing the other bracket. Mount the brackets only on solid structures of the

building. To avoid unwanted alarms due to wall movement, do not mount to

flexible walls, such as sheet metal walls (see Mounting Locations section of

the transmitter/receiver manual for more details).

CEILING

SCREWS

SLOT IN FRONT

OF BRACKET

OUTSIDE

PART

INSIDE

PART

CEILING

FIGURE 1. CEILING MOUNT BRACKET ASSEMBLY:

C0315-00

I56-2358-004

Produkt Specifikationer

Mærke:	System Sensor
Kategori:	Detektor
Model:	BEAM-MMK

Har du brug for hjælp?

Hvis du har brug for hjælp til System Sensor BEAM-MMK stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Detektor System Sensor Manualer

System Sensor B114LPBT Manual

22 August 2024

System Sensor RRS-MOD Manual

19 August 2024

System Sensor BEAM-MMK Manual

17 August 2024

System Sensor 2W-MOD2 Manual

11 August 2024

System Sensor B300-6 Manual

11 August 2024

System Sensor B300-6-BP Manual

7 August 2024

Detektor Manualer

Nyeste Detektor Manualer

SAVS CS11R Manual

6 Januar 2026

Evolveo TrackCard Manual

3 Januar 2026

Evolveo TrackTag Manual

31 December 2026

SAVS CS11W Manual

31 December 2026

SAVS CS11 Manual

24 December 2025

Garrett ACE 400 Manual

15 December 2025

Garrett ACE 300 Manual

11 December 2025

La Crosse Technology LTV-THP1-W1 Manual

10 December 2025

Garrett Goldmaster 24k Manual

9 December 2025

Garrett Pro Pointer AT Z-Lynk Manual

9 December 2025