System Sensor RRS-MOD Manual

System Sensor Detektor RRS-MOD

Læs gratis den danske manual til System Sensor RRS-MOD (4 sider) i kategorien Detektor. Denne vejledning er vurderet som hjælpsom af 32 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 16.5 anmeldelser. Har du et spørgsmål om System Sensor RRS-MOD, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/4
SPECIFICATIONS
Operating Voltage Range: 8.5 to 35 VDC
Maximum Operating Current: 25mA
Relay Contacts: 2A at 35 VDC
Operating Temperature Range: 32° to 131° F (0° to 55° C)
Operating Humidity Range: 5% to 93% non-condensing
Dimensions: 21⁄2˝ x 21⁄2˝ x 1˝
Wire connections: 18 AWG stranded, tinned, 16˝ long
RRS-MOD Reversing Relay/Synchronization Module
3825 Ohio Avenue, St. Charles, Illinois 60174
1-800-SENSOR2, FAX: 630-377-6495
www.systemsensor.com
GENERAL DESCRIPTION
The RRS-MOD polarity reversing relay/synchronization module is intended
for use with 2-wire and 4-wire i3 series detectors equipped with a built-in
sounder, models 2WTA-B, 4WTA-B, 4WTAR-B, and 4WITAR-B. It is designed
to allow all the detectors in the same loop to sound when one of the detectors
goes into alarm, and to synchronize their audible output. The RRS-MOD also
allows the silencing of the detector sounders from the alarm control panel.
The RRS-MOD may be used with an alarm zone that provides coded output for
fire and continuous output for burglary. By default the RRS-MOD’s switch is
set to “off”. Therefore, the RRS-MOD will only trigger when the alarm output
is coded. In this manner, smoke detectors will only sound from the result of a
fire, and not from a burglary alarm. In this mode, the detectors will provide a
synchronized, coded output. The RRS-MOD contains a relay that is meant for
zone applications, per UL 864.
The RRS-MOD can also be set to only trigger on continuous alarm zone sig-
nals by selecting the switch to “on”. In this mode, the detectors will provide a
synchronized, coded output.
NOTICE: This manual shall be left with the owner/user of this equipment
INSTALLATION
Install in a dry indoor location. Choose a mounting location in the control
panel within reach of the provided wire leads. Use a water/isopropyl alcohol
mixture (50/50) to clean the mounting surface. Allow surface to dry and re-
move paper backing from the Velcro and catch. Stick the Velcro in the panel
and the catch on the back of the module, then mount the module inside the
control panel. Route terminals to the appropriate terminals as noted below.
WARNING
When calculating total current draw of the control panel, remember to add
current consumption (25mA) for the polarity reversal relay module (RRS-
MOD). IMPORTANT: If the fire alarm output signal is coded, set the switch on
the RRS-MOD to “OFF”. If the fire alarm output signal is continuous, set the
switch to “ON”.
WIRING
IMPORTANT: All polarities must be observed!
1. Connect the RRS-MOD module trigger wire to the fire alarm output terminals.
A. Alarm/Bell output: (Figures 1 and 2)
Connect the purple wire to the Alarm or Bell output.
B. Alarm relay, normally open contact: (Figures 3 and 4)
1. Connect one end of the alarm relay contact output to positive
auxiliary or detector power fire alarm output.
2. Connect the purple wire to the other end of the alarm relay
contact output.
2. Connect the red and black wires to the panel auxiliary or detector power
(red to positive, black to negative).
3. 2-wire models
Connect the yellow and orange wires to the panel initiating circuit (yel-
low to positive, orange to negative).
4-wire models
Connect the yellow and orange wires to the panel detector power circuit
(yellow to positive, orange to negative).
4. 2-wire models
Connect the brown and white wires to the smoke detector power supply
input (brown to positive, white to negative).
4-wire models
Connect the brown and white wires to the smoke detector power circuit
(brown to positive, white to negative).
NOTE: In an alarm condition, a wiring-fault
trouble state may also register at the panel
when the RRS-MOD is used.
INSTALLATION AND MAINTENANCE INSTRUCTIONS
Series
D500-44-00 1 I56-2203-005
I56-2203-005

Produkt Specifikationer

Mærke: System Sensor
Kategori: Detektor
Model: RRS-MOD

Har du brug for hjælp?

Hvis du har brug for hjælp til System Sensor RRS-MOD stil et spørgsmål nedenfor, og andre brugere vil svare dig


Detektor System Sensor Manualer

System Sensor

System Sensor B114LPBT Manual

22 August 2024
System Sensor

System Sensor RRS-MOD Manual

19 August 2024
System Sensor

System Sensor BEAM-MMK Manual

17 August 2024
System Sensor

System Sensor 2W-MOD2 Manual

11 August 2024
System Sensor

System Sensor B300-6 Manual

11 August 2024
System Sensor

System Sensor B300-6-BP Manual

7 August 2024

Detektor Manualer

Nyeste Detektor Manualer

SAVS

SAVS CS11R Manual

6 Januar 2026
Evolveo

Evolveo TrackCard Manual

3 Januar 2026
Evolveo

Evolveo TrackTag Manual

31 December 2026
SAVS

SAVS CS11W Manual

31 December 2026
SAVS

SAVS CS11 Manual

24 December 2025
Garrett

Garrett ACE 400 Manual

15 December 2025
Garrett

Garrett ACE 300 Manual

11 December 2025
La Crosse Technology

La Crosse Technology LTV-THP1-W1 Manual

10 December 2025
Garrett

Garrett Goldmaster 24k Manual

9 December 2025
Garrett

Garrett Pro Pointer AT Z-Lynk Manual

9 December 2025