Tactical Fiber Systems CCRT241 Manual

Tactical Fiber Systems Ikke kategoriseret CCRT241

Læs gratis den danske manual til Tactical Fiber Systems CCRT241 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 29 personer og har en gennemsnitlig bedømmelse på 4.2 stjerner ud af 15 anmeldelser. Har du et spørgsmål om Tactical Fiber Systems CCRT241, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
1525 NW 3
rd
Street, Deerfield Beach, FL 33442 877-777-7147 www.TacticalFiber.com
TFS ClearCom/RTS 2 wire to 4 wire InterCom Interface - Mod.CCRT242
Installation and Operating Instructions with ATEM Studio Converter 2
Product Description
TFS's CCRT24 interface connects a 2 wire Clear-Com or RTS base station to the Blackmagic ATEM Studio
Converter or Studio Converter 2 's four wire intercom system . The Clear-Com or RTS base station
becomes the master intercom and communicates to both wired or wireless party line/matrix belt-paks
and the ATEM camera converters linked to the Studio Converter over fiber.
Installation
Connect the Clear-Com or RTS base station to the CCRT24 interface using a 3PIN XLR cable from any
intercom output channel. NOTE: The CCRT24 is powered by the Clear-Com or RTS base station.
Connect the ATEM Studio Converter to the CCRT24 interface using the interface cable designed for
STUDIO CONVERTER 2. (Note: The original STUDIO CONVERTER comes with a different cable.) One end
has a 16 pin DIN connector which attaches to the CCRT24. The other end has two break-out cables for
connection to the Studio Converter's Mic and Headset sockets. Insert the BLACK .20" connector plug
into the MIC input and the grey 1/4" TRS plug into the HEADSET sockets on the Studio Converter.
DIP Switch Positions
The dip switch settings at the rear of the CCRT241 should be set as follows:
Switch 1 - ON (up)
Switch 2 - ClearCom - OFF (down) RTS -ON(up)
Calibrating the Interface
Your TFS CCRT24 Clear-Com/RTS interface was factory nulled with an MS-702 Clear-Com base station
attached to a Blackmagic ATEM Studio Converter. You may have to tweak the null adjustments to match
your particular Studio converter using an ear set and a small screwdriver. To null the interface, plug in
the ear set into the 1/8" jack to the right of the interface and adjust the RLC trim pots for minimum
noise...then unplug the ear set. IMPORTANT: You must unplug the ear set after nulling the interface

Produkt Specifikationer

Mærke: Tactical Fiber Systems
Kategori: Ikke kategoriseret
Model: CCRT241

Har du brug for hjælp?

Hvis du har brug for hjælp til Tactical Fiber Systems CCRT241 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Tactical Fiber Systems Manualer

Tactical Fiber Systems

Tactical Fiber Systems CCRT242 Manual

4 September 2024
Tactical Fiber Systems

Tactical Fiber Systems CCRT241 Manual

2 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Siemens

Siemens WQ32G28IL Manual

6 December 2025
MDT

MDT BE-TA550606.02 Manual

6 December 2025
Opticis

Opticis USC-CC32 Manual

6 December 2025
Audio-Technica

Audio-Technica AT33xMONO Manual

6 December 2025
Bosch

Bosch SPI4EMS24E Manual

6 December 2025
Fostex

Fostex P1000K Manual

6 December 2025
Advantech

Advantech UTC-124I1 Manual

6 December 2025
Anton/Bauer

Anton/Bauer Titon Micro Kit Manual

6 December 2025
Philips

Philips Zoom! DayWhite DIS130 Manual

6 December 2025
Opticis

Opticis USB-FC30AA Manual

6 December 2025