Taylor 1512RMT Manual

Taylor Vejrstation 1512RMT

Læs gratis den danske manual til Taylor 1512RMT (5 sider) i kategorien Vejrstation. Denne vejledning er vurderet som hjælpsom af 20 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 10.5 anmeldelser. Har du et spørgsmål om Taylor 1512RMT, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/5

WeatherGuide™ System with Remote Sensor

Models 2 / 2RMT 151 151

Instruction Manual

Welcome to the Taylor® WeatherGuide™ System. Simple, reliable, accurate…it allows you to monitor indoor

or outdoor locations from one room. The base unit reads indoor conditions, while the remote sensor wirelessly

reports outdoor weather conditions back to the base unit for an all- -one weather display. in

NOTE: Some units have a static cling label over the digital display. Please remove before use.

BATTERY INSTALLATION

The base unit operates on 2 AA batteries and the remote sensor operates on 2 AAA batteries (batteries not

included). Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc) or rechargeable (ni-

cad, ni-mh, etc.) batteries.

( Lithium batteries are recommended in extremely cold or hot locations.) Tip:

IMPORTANT: Install batteries in the base unit first, then the remote sensor, otherwise the units’ transmissions

may not properly connect. Place the base unit as close as possible to the remote sensor when installing batteries.

Base Unit

The battery compartment is located on the back of the unit. Remove the battery compartment door. Install (2)

AA size batteries into the battery compartment according to the polarity markings. Replace the battery

compartment door.

Remote Sensor

The battery compartment is located on the back of the unit. Slide oﬀ the battery compartment cover. Install (2)

AAA size batteries into the battery compartment according to the polarity markings. Replace the battery

compartment door.

After Batteries are Installed:

Allow at least 3 minutes for the base unit to analyze current temperature conditions and connect with the remote

sensor. A transmission signal icon will begin to ﬂash on the base unit during this time. After 3 minutes, (“ ”)

the transmission signal will only ﬂash when a signal is received from the remote sensor.

The remote transmits temperatures once a minute. A transmission signal icon “ ” on the remote ﬂashes when

a signal is sent.

Note: While the base unit is in “analyzing” mode, other functions (such as switching to outdoor temperatures

and setting the clock) may not be operational. Once the “analyzing” mode is complete, the other functions will

become operational.

ADDITIONAL REMOTE SENSORS

A maximum of 3 remote sensor units can be used with the base unit; one is included. Should you purchase one

or two additional remote units (Model 1512RMT, sold separately), ﬁrst install batteries in the remote, and then

press the CH button inside the remote’s battery compartment to select Channel 2 or Channel 3. The Channel

number assigned will appear on the remote’s LCD screen.

TEMPERATURE READI NGS

● The base unit displays the indoor temperature (“IN ”) from its location.DOOR

● The remote sensor transmits outdoor temperature (“OUT ”) from its location back to the base unit.DOOR

● To switch between outdoor or auto scroll displays UP/, press the “ CH” (up/channel) button.

- Channel icon ( , CH2, or ) indicates A CH1 CH3 = which remote sensor’s readings are displayed.

- The indicates the auto scroll option is on. The base unit will automatically scroll between indoor “ ” icon =

readings and remote sensor readings and display each for 5 seconds.

● To switch between Fahrenheit and Celsius temperature displays:

- Base unit - DOWN/Press the “ CF” button on the base unit to change the temperature readings on the base

unit. Both indoor and outdoor readings will display in F or ° °C.

- Remote sensor - Press the “C/F” button inside the battery compartment of the remote sensor to change the

temperature display on the remote sensor. (Only the remote sensor display will change; the base unit

display will not change.)

CLOCK FEATURES

A) Clock Setting

1. Press and hold the “SET” button for 2 seconds to enter Clock Setting “24 Hr” or “12 Hr” blinks.mode.

2. /CHPress the “UP ” or “DOWN/CF” button to toggle between 12 and 24 hour clock mode. Press “SET” to

conﬁrm. The hour digits blink.

2. Press “ or “DOWN to change the hours. Press “SET” to confirm. The minute digits blink.UP/CH” /CF”

3. Press “ ” or “DOWN ” to change the minutes. Press “SET” to confirm. UP/CH /CF A language selection blinks

in the “DAY” window below the clock digits.

4. Press “UP/CH” or “DOWN/CF” to toggle between language selections. Press “SET” to confirm the displayed

language. The year digits blink.

( ENG = English, FRE French, NET = Netherlands, ESP = Spanish, DAN = Danish, GER = German) Note: =

5. Press “UP/CH” or “DOWN/CF” to change the . Press “SET” to confirm.year The month digit blinks.

6. Press “UP/CH” or “DOWN/CF” to change the s “SET” to confirm. The month. Pres date digit blinks.

7 /CH. Press the “UP ” or “DOWN ” button to change the date. Press “SET” to confirm. /CF The hour and minute

digits reappear instead of the year digits. The clock is set.

Notes: If no buttons are pressed within 15 seconds, the unit will automatically exit Clock Setting mode.

Until a time has been set, the clock will count up the time since battery installation.

B) Alarm Setting this unit features 2 alarm settings. To set an alarm: –

1. Press the “SET” button to switch the clock display to Alarm 1 (“A1”).

2. Press and hold “SET” for 2 seconds to enter Alarm Setting mode. The alarm hour digits blink.

3. Press “UP/CH” or “DOWN/CF” to change the hours. Press “SET” to confirm. The minute digits blink.

4. Press “UP/CH” or “DOWN/CF” to change the . Press “SET” to confirm. minutes

5. Press “ALARM”. The Alarm Bell Icon 1 (“ ”) appears above the hour digits, indicating Alarm 1 is active.

6. Press “SET” to switch the display to Alarm 2 (“A2”). Repeat steps to set Alarm 2. The Alarm Bell Icon 2

(“ ”) appears above the minute digits, indicating Alarm 2 is active. Press “SET” to return to the clock display.

If you only wish to set one alarm, press “SET” until the clock display appears.

C) To Silence Alarms:

● To silence an alarm for 5 minutes, press the “SNOOZE” button.

● To stop the alarm for one day, press any button except If the alarm bell icon still appears on “SNOOZE”.

the screen, the alarm will sound again the next day.

● To deactivate an alarm, press the “ALARM” button until the desired Alarm Bell Icon (“ ”) disappears.

(You may do this while viewing either the Clock display or the Alarm display.)

- One Alarm Bell icon = indicates one alarm will ring at the set time (Alarm 1 or Alarm 2).

- Two Alarm Bell icons = indicates both alarms will ring at the set time.

- No Alarm Bell icons = no alarms will ring; both are deactivated.

Note: If no buttons are pressed within 15 seconds, the unit will automatically exit Alarm Setting mode.

D) To View Clock or Alarm Displays

Press the “SET” button to toggle between the Clock, Alarm 1 and Alarm 2 displays.

Produkt Specifikationer

Mærke:	Taylor
Kategori:	Vejrstation
Model:	1512RMT

Har du brug for hjælp?

Hvis du har brug for hjælp til Taylor 1512RMT stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Vejrstation Taylor Manualer

8 Januar 2025

24 August 2024

24 August 2024

24 August 2024

Taylor 5262313 Manual

24 August 2024

Taylor 1383-21 Manual

23 August 2024

Taylor 1511 Manual

23 August 2024

Taylor 1512RMT Manual

23 August 2024

Taylor 1381-21 Manual

23 August 2024

Taylor 1512 Manual

23 August 2024

Vejrstation Manualer

Nyeste Vejrstation Manualer

Levenhuk Wezzer SN10 Manual

17 Juni 2025

Levenhuk Wezzer PH20 Manual

16 Juni 2025

Levenhuk Wezzer Teo TH10 Manual

16 Juni 2025

Levenhuk Wezzer Teo TH30 Manual

16 Juni 2025

Levenhuk Wezzer Teo TH50 Manual

16 Juni 2025

Levenhuk Wezzer Air PRO DM20 Manual

16 Juni 2025

Levenhuk Wezzer Teo TH40 Manual

15 Juni 2025

Levenhuk Wezzer PRO LP240 Manual

15 Juni 2025

Levenhuk Wezzer BASE L50 Manual

15 Juni 2025

Levenhuk Wezzer SN70 Manual

15 Juni 2025