Tektronix P6316 Manual

Tektronix Ikke kategoriseret P6316

Læs gratis den danske manual til Tektronix P6316 (6 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 12 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 6.5 anmeldelser. Har du et spørgsmål om Tektronix P6316, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/6
xx
Product Description
The P6316 digital probe connects the Tektronix MSO2000
Series of mixed-signal oscilloscopes to digital buses and signals
on your target system. The probe breaks out 16 data channels
over two 2x8-pin headers (GROUP 1 and GROUP 2). Each
header includes eight signals on one row and eight grounds
along the opposite row.
A pair of interchangable flying lead sets are included with the
n on each
end and eight signal leads for connecting to individual test
points.
Connecting the Probe to the Oscilloscope
Connect the probe as shown in the illustration below.
1. Insert the probe label-side up into the receptacle.
2. To remove the probe, squeeze the buttons on the side and
pull out the probe.
Connecting the Probe to Your Circuit
Attach the probe to the circuit using the connectors and adapters
shown on the back of these instructions. Select the best method
for your needs, and then proceed to Setting up the Probe.
Setting up the Probe
Press the D15-D0 button to set and view the following
parameters of each digital channel:
Threshold voltage and vertical position
Signal height (set once for all 16 channels)
Channel label
The default settings are 1.4 V thresholds with no channel labels.
Use the B1 and B2 buttons to set and view bus characteristics
such as:
Clock type
Bus type (Serial or Parallel)
Bus width
Display format (Hex, Binary, ASCII)
Parallel bus setup information is resident on the MSO Family
of oscilloscopes. However, for other buses such as CAN and
I2C, you must have the appropriate application key. See your
oscilloscope manual or product data sheet for nomenclature
and ordering details.
Functional Check
Logic activity immediately displays on all connected, active
channels. If you do not see an active signal:
1. Press Trigger.
2. Select Edge for trigger type.
3. Select the channel that you are setting up as the source.
4. Press Aut
oset.
If you do not see an active signal, try another probe channel (or
analog probe) to verify circuit activity at the test point.
Specifications
Table 1: Electrical and mechanical specifications
Characteristic Description
Input channels 16
Threshold voltage range ±20 V
Threshold accuracy
±100 mV + 3% of threshold setting
Minimu
m signal swing
500 mV p
-p
Maximum signal swing ±20 V centered around the
threshold voltage
Maximum nondestructive
input signal to probe
±40 V p-p
Input resistance
101 kΩ
Input capacitance 8.0 pF
Minimum detectable input
pulse
5 ns
Probe length
0.9 m (3 ft)
Table 2: Environmental specifications
Characteristics Description
Temperature
Maximum operating
Minimum operating
Nonoperating
+50 °C (+122 °F)
0 °C (+32 °F)
–40 °C to +71 °C
(–40 °F to +160 °F)
Humidity
5% to 95% relative humidity at up
to +30 °C (+86 °F)
5% to 60% RH above +30° C
(+86
°F) up to +50 °C (+122 °F),
non-condensing
Altitude
Oper
ating
Nonoperating
3 km (9,843 ft) maximum
12 km
(39,370 ft) maximum
Electrostatic Immunity The probe is not static sensitive
Equipment Recycling. This product complies
with the European Union’s requirements according
to Directive 2002/96/EC on waste electrical
and
electronic equipment (WEEE). For more
information about recycling options, check the
Support/Service section of the Tektronix Web site
(www.tektronix.com).
Safety Summary
Connect and Disconnect Properly. Connect the probe output
to the measurement instrument before connecting the probe
to the circuit under test. Disconnect the probe input and the
probe ground from the circuit under test before disconnecting
the probe from the measurement instrument.
Observe All Terminal Ratings. To avoid fire or shock hazard,
observe all ratings and markings on the product. Consult the
product manual for further ratings information before making
connections to the product.
Do not Operate Without Covers. Do not touch exposed
connections and components when power is present.
Avoid Exposed Circuitry. Do not touch exposed connections
and components when power is present.
Do Not Operate With Suspected Failures. If you suspect there is
damage to this product, have it inspected by qualified service
personnel.
Do Not Operate in Wet/Damp Conditions. Do Not Operate in an
Explosive Atmosphere.
Keep Product Surfaces Clean and Dry.
Safety Terms and Symbols Terms in This Manual.
These terms may appear in this manual:
WARNING. Warning statements identify conditions or
practices that could result in injury or loss of life.
CAUTION. Caution statements identify conditions or
practices that could result in damage to this product or
other property.
Symbols on the Product. These symbols may appear on the
product:
Typical Application
1. Use the P6316 probe to view digital signals on a system
bus.
2. Use analog probes, such as the P6139A or P2221 probes
to view analog waveform information.
P6316
Digital Probe
Instruct
ions
x
1
*P0712
34500*
071-2345-00

Produkt Specifikationer

Mærke: Tektronix
Kategori: Ikke kategoriseret
Model: P6316

Har du brug for hjælp?

Hvis du har brug for hjælp til Tektronix P6316 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Tektronix Manualer

Tektronix

Tektronix TBS1052C Manual

11 Juli 2025
Tektronix

Tektronix TICP100 Manual

10 Juli 2025
Tektronix

Tektronix TLP058 Manual

8 Juli 2025
Tektronix

Tektronix P6316 Manual

4 September 2024
Tektronix

Tektronix P6616 Manual

4 September 2024
Tektronix

Tektronix 2460-EC Manual

20 Juli 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Navitel

Navitel ALC 01 Manual

5 November 2025
SilentiumPC

SilentiumPC Vero L3 Bronze 600W Manual

5 November 2025
JoeCo

JoeCo BlackBox BBR1-U Manual

5 November 2025
Ices

Ices IWO-630 Manual

5 November 2025
JMAZ

JMAZ Crazy Beam 40 Fusion Manual

5 November 2025
Lexar

Lexar Professional LRW530U Manual

5 November 2025
Zotac

Zotac GeForce GT 610 Manual

5 November 2025
NeXtime

NeXtime Basic Dome 3157 ZW Manual

5 November 2025
DS18

DS18 PU110A Manual

5 November 2025
JMAZ

JMAZ Galaxy Tube Manual

5 November 2025