Tektronix TLP058 Manual

Tektronix Ikke kategoriseret TLP058

Læs gratis den danske manual til Tektronix TLP058 (8 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 3 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 2 anmeldelser. Har du et spørgsmål om Tektronix TLP058, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

Product description

The TLP058 FlexChannel

logic probe connects all instruments

with FlexChannel

inputs to digital buses and signals on your

device under test (DUT). The probe contains 8 data channels.

All leads include a ground connection at the t

ip. You can

connect the probe leads separately to the target system, or group

the leads together using the probe tip holde

Connecting the probe to the oscilloscope

1. Move the locking lever to the unlocked position then let

go to reset locking lever to the center position.

2. Insert the probe into a FlexChannel channel until fully

seated and the lock mechanism clicks.

3. Mov

e the locking lever to the locked position. The status

light should be a solid green.

NOT

E. It is normal for the logic probe Status light to ﬂash

green when the oscilloscope is powering on, and will turn to a

ste

ady green once the oscilloscope is fully running.

NOTE. If the status LED continues ﬂashing green, ashingﬂ

red

, or is a steady red, contact Tektronix Customer Support

for assistance.

4. To r

emove the probe, move and hold the locking lever at

the unlocked position and pull out the probe.

Connecting the probe to your circuit

Attach the probe to the circuit using the connectors and adapters

shown on the back of these instructions. Select the best method

for your needs, and then go to Setting up the Probe.

Setting up the probe

The oscilloscope automatically detects and conﬁgures channels

when you connect a logic probe.

To set and view the digital channel parameters, add the channel

with the connected logic probe to the display. Double-tap

the Waveform badge for the logic probe channel to open the

conﬁguration menu. Digital channel settings include threshold

voltage (default is 1.4 V), signal height (for all channels), and

channel labels.

Using the probe

See the oscilloscope documentation and Help topics for how to

display and trigger on digital logic signals and buses.

Functional check

Follow th

e instructions for connecting the probe to the

oscilloscope and setting up the probe. Connect your probe

leads to a

ctive logic signals on your DUT. You should see logic

activity immediately on all connected, active channels. If you

do not see

an active signal, use an analog probe to verify signal

activity on the logic signal points.

Typical

application

1. Use the logic probe to view digital signals on a system bus.

2. Use an analog probe to view analog waveform information

of a digital signal.

Accessories

The probe comes standard with a Logic Probe Accessory Kit

(Tektronix part number 020-3170-XX). See the illustration on

the following page. See the label in the accessories box lid for

information on the individual accessories.

Speciﬁcations

Table 1: Electrical and mechanical speciﬁcations

Characteristic Description

Input channels 8 digital

Inpu

t resistance

100 kΩ±1.0%

Input capacitance 3.0 pF

Input signal swing

Minimum 400 mV p-p

Maximum

30 V p-p, ≤200 MHz (centered around

the

DC threshold voltage) at the probe tip

10 V p-p, ≥200 MHz (centered around

the DC threshold voltage) at the probe tip

Max

imum nondest–

ructive input signal

30 V

p-p, ±42 V peak, ±50 V

Characteristic Description

Threshold voltage ± 40 V

Minimum detectable

pulse width

1 ns

Maximum input

toggle rate

500 MHz

Maximum sample

rate

6.25 GS/s

Digital to analog

trigger skew

5 ns

Probe length

1.0 m (3.28 ft)

Table 2: En

vironmental speciﬁcations

Characteristic Description

Temperature

Operating

Nonoperating

0 °C to +50 °C (+32 °F to +122 °F)

–40 °C to +71 °C (–40 °F to +160 °F)

Humidity Noncondensing, and as limited by a maximum

Wet-Bulb temperature of +39 °C (+102 °F)

Operating 5% to 90% relative humidity to +40 °C (104 °F)

5% to 55% relative humidity +40 °C to +50 °C

(+104 °F to 122 °F)

Nonoperating

5% to 90% relative humidity to +40 °C

(+104 °F)

5% to 39% relative humidity +40 °C to +60 °C

(+104 °F to 140 °F)

Altitude

Operating

Nonoperating

3,000 m (9,842 ft) maximum

12,000 m (39,370 ft) maximum

Equipment Recycling. This symbol indicates that

this product complies with the applicable European

Union requirements according to Directives

2012/19/EU and 2006/66/EC on waste electrical

and electronic equipment (WEEE) and batteries.

For information about recycling options, check the

Tektronix Web site (www.tek.com/productrecycling).

Safety summary

Connect and disconnect properly. Connect the probe output

to the measurement instrument before connecting the probe

to the circuit under test. Disconnect the probe input and the

probe ground from the circuit under test before disconnecting

the probe from the measurement instrument.

Observe all terminal ratings. To avoid ﬁre or shock hazard,

observe all ratings and markings on the product. Consult the

product manual for further ratings information before making

connections to the product. Connect the probe reference lead to

earth ground only.

Do not operate without covers.

Avoid exposed circuitry. Do not touch exposed connections

and components when power is present.

Do not operate with suspected failures. If you suspect there is

damage to this product, have it inspected by qualiﬁed service

personnel.

Do not operate in wet/damp conditions.

Do not operate in an explosive atmosphere.

Keep product surfaces clean and dry.

Safety terms and symbols in this manual.

These terms may appear in this manual:

WARNING. Warning statements identify conditions or

practices that could result in injury or loss of life.

CAUTION. Caution statements identify conditions or

practices that could result in damage to this product or

other property.

Symbols on the product. This symbol may appear on the

product:

Contacting Tektronix

Web site: www.tektronix.com

Phone: 1-800-833-9200

Address: Tektronix, Inc.

Department or name (if known)

14200 SW Karl Braun

Drive P.O. Box 500

Beaverton, OR 97077

USA

Email:

techsupport@tektronix.com

War

ranty information

For warranty information, go to www.tektronix.com/warranty.

TLP058

FlexChannel

Logic Probe

Instruct

ions

*P0713

51503*

071-3515-03

Connecting the probe to the circuit

Produkt Specifikationer

Mærke:	Tektronix
Kategori:	Ikke kategoriseret
Model:	TLP058

Har du brug for hjælp?

Hvis du har brug for hjælp til Tektronix TLP058 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Tektronix Manualer

Tektronix TICP100 Manual

10 Juli 2025

Tektronix TLP058 Manual

8 Juli 2025

Tektronix P6316 Manual

4 September 2024

Tektronix P6616 Manual

4 September 2024

Tektronix 2460-EC Manual

20 Juli 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Panasonic PalmCam PV-SD5000 Manual

10 Juli 2025

Voigtländer Bessamatic Manual

10 Juli 2025

Leviton D6701 Manual

10 Juli 2025

Microchip USB7216C Manual

10 Juli 2025

Parkside PKHAP 20-Li C3 Manual

10 Juli 2025

Merging Anubis Pro SPS Manual

10 Juli 2025

Hazet 1987N-4 Manual

10 Juli 2025

Microchip MCP48FVB04 Manual

10 Juli 2025

Octavio STREAM Manual

10 Juli 2025

Voigtländer Vito C Manual

10 Juli 2025