Tektronix P6616 Manual

Tektronix Ikke kategoriseret P6616

Læs gratis den danske manual til Tektronix P6616 (8 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 8 personer og har en gennemsnitlig bedømmelse på 4.2 stjerner ud af 4.5 anmeldelser. Har du et spørgsmål om Tektronix P6616, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/8
xx
Product Description
The P6616 general-purpose logic probe connects the Tektronix
MSO/DPO5000 Series and MSO4000B Series of mixed-signal
oscilloscopes to digital buses and signals on your target system.
The probe contains 16 data channels split between two lead sets
(GROUP 1 and GROUP 2).
All leads include a ground connection at the tip. You can
connect the probe leads separately to the target system, or group
the leads together using the probe tip holders.
Connecting the Probe to the Oscilloscope
1. Insert the probe label-side up into the connector on the
oscilloscope.
2. To remove the probe, squeeze the buttons on the side and
pull out the probe.
Connecting the Probe to Your Circuit
Attach the probe to the circuit using the connectors and adapters
shown on the back of these instructions. Select the best method
for your needs, and then proceed to Setting up the Probe.
Setting Up the Probe
To set and view the digital channel parameters, do the
following:
On MSO/DPO5000 Series instruments, select
Vertical>Digital Setup.
On MSO/DPO4000B Series instruments, push the D15–D0
button.
The parameters listed below can be set on each digital channel:
Threshold voltage and vertical position (the default
threshold setting is 1.4 V)
Signal height and position (set once for all 16 channels)
Channel label
To set and view bus characteristics, do the following:
On MSO/DPO5000 Series instruments, use the controls in
the Bus Setup screen.
On MSO/DPO4000B Series instruments, push the B1 to
B4 buttons.
The setup screens allow you to set and view bus characteristics
such as:
Clock type
Bus type (Serial or Parallel)
Bus width
Display format (Hex, Binary, or ASCII symbols)
Parallel bus setup information is resident on some oscilloscope
models. However, for other buses such as SPI and I2C, you
must have the appropriate option. See your oscilloscope manual
or product data sheet for nomenclature and ordering details.
Functional Check
Logic activity immediately displays on all connected, active
channels. If you do not see an active signal:
1. Push the Trigger button.
2. Select Edge for trigger type.
3. Select the channel that you are setting up as the source.
4. On MSO/DPO4000B Series instruments, push the Autoset
button.
If you do not see an active signal, try another probe channel (or
analog probe) to verify circuit activity at the test point.
Typical Application
1. Use the P6616 probe to view digital signals on a system
bus.
2. Use an analog probe, such as the TPP0500 or TPP1000
active probe to view analog waveform information.
Accessories
The following standard accessories ship with the probe and are
shown in the illustration on the following page.
Item Description Quantity Part number
— Logic probe accessory kit Item 1–6 020-2662-XX
1 Extension ground tip
1 set of 20
020-2711-XX
2 Probe tip
1 set of 10
131-5638-11
3
IC grabber 1 set of 20
020-2733-XX
4 Probe tip holder 2 ea 352-1115-XX
5
8” Ground lead 1 set of 2
020-2713-XX
6
3” Ground lead 1 set of 8
020-2712-XX
Instructions
1
1 ea 071-2831-XX
1
Instructions are included with the probe, but n
ot in the accessory kit.
The instructions can be downloaded at www.tektronix.com/manuals.
These optional accessories can be ordered for your probe:
Description Part number
P6960 Probe D-MAX Footprint to
Square Pin Header Adapter
NEX-P6960PIN
Specifications
Table 1: Electrical and mechanical specifications
Characteristic Description
Input channels 16 digital
Input resistance
100 kΩ±1.0%
Input capac
itance
3.0 pF
Input signal swing
Minimum 400 mV p-p
Maximum
30 V p-p, ≤200 MHz (centered around
the DC threshold voltage) at the probe tip
10 V p-p, ≥200 MHz (centered around
the DC threshold voltage) at the probe tip
Maximum nondest–
ructive input signal
30 V p-p, 42 V peak, ±50 VDC
Threshold voltage ± 40 V
Minimum detectable
pulse width
1 ns
Maximum input
toggle rate
500 MHz
Digital channel-to-
digital channel skew
200 ps
Probe length
1.0 m (3.28 ft)
Table 2: Environmental specifications
Characteristic Description
Temperature
Operating
Nonoperating
0 °C to +50 °C (+32 °F to +122 °F)
–55 °C to +75 °C (–67 °F to +167 °F)
Humidity
Operating
Nonoperating
5% to 95% relative humidity
10% to 95% relative humidity
Altitude
Operating
Nonop
erating
4.6 km (15,092 ft) maximum
15 km (
50,000 ft) maximum
Equipment Recycling. This product complies
with the European Union’s requirements according
to Dire
ctive 2002/96/EC on waste electrical
and electronic equipment (WEEE). For more
information about recycling options, check the
Support/Service section of the Tektronix Web site
(www.tektronix.com).
Safety Summary
Connect and Disconnect Properly. Connect the probe output
to the measurement instrument before connecting the probe
to the circuit under test. Disconnect the probe input and the
probe ground from the circuit under test before disconnecting
the probe from the measurement instrument.
Observe All Terminal Ratings. To avoid fire or shock hazard,
observe all ratings and markings on the product. Consult the
product manual for further ratings information before making
connections to the product.
Do not Operate Without Covers. Do not touch exposed
connections and components when power is present.
Avoid Exposed Circuitry. Do not touch exposed connections
and components when power is present.
Do Not Operate With Suspected Failures. If you suspect there is
damage to this product, have it inspected by qualified service
personnel.
Do Not Operate in Wet/Damp Conditions. Do Not Operate in an
Explosive Atmosphere.
Keep Product Surfaces Clean and Dry.
Safety Terms and Symbols in This Manual.
These terms may appear in this manual:
WARNING. Warning statements identify conditions or
practices that could result in injury or loss of life.
CAUTION. Caution statements identify conditions or
practices that could result in damage to this product or
other property.
Symbols on the Product. This symbol may appear on the
product:
Contacting Tektronix
Web site: www.tektronix.com
Phone: 1-800-833-9200
Address: Tektronix, Inc.
Department or name (if known)
14200 SW Karl Braun
Drive P.O. Box 500
Beaverton, OR 97077
US
A
Email:
techsupport@tektronix.com
Warranty Information
For warranty information, go to www.tektronix.com/warranty.
P6616
General-Purpose Logic Probe
Instruct
ions
x
1
*P0712
83101*
071-2831-01

Produkt Specifikationer

Mærke: Tektronix
Kategori: Ikke kategoriseret
Model: P6616

Har du brug for hjælp?

Hvis du har brug for hjælp til Tektronix P6616 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Tektronix Manualer

Tektronix

Tektronix TBS1052C Manual

11 Juli 2025
Tektronix

Tektronix TICP100 Manual

10 Juli 2025
Tektronix

Tektronix TLP058 Manual

8 Juli 2025
Tektronix

Tektronix P6316 Manual

4 September 2024
Tektronix

Tektronix P6616 Manual

4 September 2024
Tektronix

Tektronix 2460-EC Manual

20 Juli 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Leifheit

Leifheit TwistCut 23041 Manual

4 November 2025
Ikea

Ikea KVISSLE 901.980.30 Manual

4 November 2025
Beverage-Air

Beverage-Air Horizon HRP2HC-1HG Manual

4 November 2025
Scheppach

Scheppach MR200-61 Manual

4 November 2025
Beverage-Air

Beverage-Air Horizon HF2HC-1S Manual

4 November 2025
Iogear

Iogear SuperSpeed GFR304SD Manual

4 November 2025
EtherWAN

EtherWAN EX42905 Manual

4 November 2025
ANCEL

ANCEL DP500 Manual

4 November 2025
Zotac

Zotac GAMING GeForce RTX 2060 AMP Manual

4 November 2025
J-Tech Digital

J-Tech Digital JTECH-EX-120M-UN-R Manual

4 November 2025