Tennsco CVD1472 Manual

Tennsco Skab CVD1472

Læs gratis den danske manual til Tennsco CVD1472 (4 sider) i kategorien Skab. Denne vejledning er vurderet som hjælpsom af 16 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 8.5 anmeldelser. Har du et spørgsmål om Tennsco CVD1472, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/4
GENERAL SAFETY INFORMATION
Some parts may have sharp edges. CARE must be taken when handling
For safety, wear a pair of work gloves when assembling or performing
LIMITED WARRANTY
Tennsco warrants goods purchased hereunder to be free of defects in materials and workmanship for a period of one (1) year from th
in the event goods are damaged as a result of misuse, abuse, neglect, accident, improper application, modication or repair by person
shipment, or where the date stamps on the goods have been defaced, modied or removed. UNLESS CONSIDERED UNENFORCEABLE
a. ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A
b. BUYERS REMEDY, IF ANY, FOR ANY DEFECTIVE GOODS SHALL BE LIMITED TO A REFUND BY SELLER OR REPLACEMENT
NO GOODS ACCEPTED FOR RETURN WITHOUT PRIOR APPROVAL. Seller shall have the right to inspect any goods claimed to be defective at Buyers place of business or require Buyer to return the
goods to Seller for inspection on Seller’s premises. Transportation charges covering returned goods will be borne by Seller only if such goods are proven to be defective, are covered by this warranty
and are returned within the warranty period stated above.
ASSEMBLY INSTRUCTIONS & PARTS MANUAL
PK-1760918
RETAIN INSTRUCTIONS FOR FUTURE REFERENCE
Combination Storage Cabinet
Unassembled Model 1472 or CVD1472
Tennsco LLC., Dickson, TN 37056-1888 • (866) 446-8686
LOAD CAPACITIES PER SHELF LEVEL
36w x 18d
18w x 18d
200 lbs.
75 lbs.
UNIT SIZE
WEIGHT CAPACITY
EVENLY DISTRIBUTED
ASSEMBLY OF 1472 or CVD1472 CABINET
Tools Needed: A free
11
/ ” nut driver is included with each Tennsco cabinet. 32
Two people are recommended for assembly. Approximate assembly time: 30-40 minutes.
2. Place the cabinet back (Ref. No. 1) on a
protected surface to prevent
scratching the paint.
The ange on the
bottom of the back
should be facing upward.
1. The reference numbers used throughout this sheet refer
to the illustration on the back cover. This is to help you
to identify the various parts as they are mentioned.
3. Attach the left side (Ref. No. 2) to the back by placing
ange (A) around the back and bolting together with
seven bolts and nuts (Ref. Nos. 21 & 22). Be sure that the
lances on all shelf adjustment strips (B) are pointing in the
same direction.
5. Insert the shelf (Ref. No. 4) into
the second lance of the side
and back panels.
6. Attach the top (Ref. No. 5) to the unit by sliding the outer ange
over the back of the unit and the side ange of the side panel on
the unit. The threaded studs should go through
the holes in the top lange of the side and
fasten with three nuts. Attach the back
to the top using four bolts
and nuts.
4. Attach the right side (Ref. No. 3) to the back in the same
manner as you did in step 3, again, making sure that
the ange is around the back and that the lances on the
shelf adjustment strips are pointed in the same direction
as those on the back and left side.
8. Place the rear ange of the bottom (Ref. No. 7) into the
bottom lances of the back. The ange with two holes should
face the front, hanging over the sill. Insert the bolts through
the bottom and still with the head
facing the front of the unit.
Secure with two nuts.
Tighten all bolts.
All lances point UP on
both backs and side.
Flange goes
under back.
Flange faces upward.
Flanges
face upward
Slide ends in to the slots
on the bottom of the sides.
Nuts placed loosely
on studs of the sill.
Insert bottom into
bottom lances.
B
A
NOTE: When bolting the unit together, leave
the bolts slightly loose until Step 8, unless
otherwise specified.
NOTE: All illustrations show a solid door. Assembly
for C-Thru doors (CVD1472) is identical.
Two holes must
be in front
Inset A
Use 2
nd
lance
7. Next, attach the sill (Ref. No. 6) to the sides, as shown above.
Place nuts loosely on each of the studs and slide the ends of the
sill into the slots on both sides of the unit. Then, securely tighten
the nuts.

Produkt Specifikationer

Mærke: Tennsco
Kategori: Skab
Model: CVD1472

Har du brug for hjælp?

Hvis du har brug for hjælp til Tennsco CVD1472 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Skab Tennsco Manualer

Tennsco

Tennsco J1878C-N Manual

16 August 2024
Tennsco

Tennsco 1436 Manual

15 August 2024
Tennsco

Tennsco CVD7214 Manual

14 August 2024
Tennsco

Tennsco 7220 Manual

14 August 2024
Tennsco

Tennsco JSD2478SU Manual

12 August 2024
Tennsco

Tennsco CVD1472 Manual

12 August 2024
Tennsco

Tennsco J2478A-N-W Manual

11 August 2024
Tennsco

Tennsco 7814 Manual

10 August 2024
Tennsco

Tennsco 2472 Manual

9 August 2024
Tennsco

Tennsco 1471 Manual

9 August 2024

Skab Manualer

Nyeste Skab Manualer

Ikea

Ikea MAXIMERA 904.170.42 Manual

20 Februar 2025
Ikea

Ikea UTRUSTA 502.132.97 Manual

20 Februar 2025
Ikea

Ikea UTRUSTA 902.135.73 Manual

20 Februar 2025
Ikea

Ikea UTRUSTA 602.711.59 Manual

20 Februar 2025
Ikea

Ikea UTRUSTA 903.669.24 Manual

20 Februar 2025
Ikea

Ikea UTRUSTA 403.059.71 Manual

20 Februar 2025
Ikea

Ikea NYTTIG 302.432.95 Manual

20 Februar 2025
Ikea

Ikea MAXIMERA 603.193.59 Manual

20 Februar 2025
Ikea

Ikea MAXIMERA 603.193.64 Manual

20 Februar 2025
Ikea

Ikea MAXIMERA 903.193.48 Manual

20 Februar 2025