Tennsco CVD1480 Manual

Tennsco Skab CVD1480

Læs gratis den danske manual til Tennsco CVD1480 (4 sider) i kategorien Skab. Denne vejledning er vurderet som hjælpsom af 14 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 7.5 anmeldelser. Har du et spørgsmål om Tennsco CVD1480, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

GENERAL SAFETY INFORMATION

Some parts may have sharp edges. CARE must be taken when handling

For safety, wear a pair of work gloves when assembling or performing

LIMITED WARRANTY

Tennsco warrants goods purchased hereunder to be free of defects in materials and workmanship for a period of one (1) year from th

in the event goods are damaged as a result of misuse, abuse, neglect, accident, improper application, modication or repair by person

shipment, or where the date stamps on the goods have been defaced, modied or removed. UNLESS CONSIDERED UNENFORCEABLE

a. ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A

b. BUYERS REMEDY, IF ANY, FOR ANY DEFECTIVE GOODS SHALL BE LIMITED TO A REFUND BY SELLER OR REPLACEMENT

EVENT INCLUDE DAMAGES OF ANY KIND, WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE.

NO GOODS ACCEPTED FOR RETURN WITHOUT PRIOR APPROVAL. Seller shall have the right to inspect any goods claimed to be defective at Buyers place of business or require Buyer to return the

goods to Seller for inspection on Seller’s premises. Transportation charges covering returned goods will be borne by Seller only if such goods are proven to be defective, are covered by this warranty

and are returned within the warranty period stated above.

PK-1740918

ASSEMBLY INSTRUCTIONS & PARTS MANUAL

RETAIN INSTRUCTIONS FOR FUTURE REFERENCE

Standard Storage Cabinet

Unassembled Model 1480 or CVD1480

Tennsco LLC., Dickson, TN 37056-1888 • (866) 446-8686

LOAD CAPACITIES PER SHELF LEVEL

36w x 24d

200 lbs.

UNIT SIZE

WEIGHT CAPACITY

EVENLY DISTRIBUTED

ASSEMBLY OF 1480 or CVD1480 CABINET

Tools Needed: A free

/ ” nut driver is included with each Tennsco cabinet. 32

Two people are recommended for assembly. Approximate assembly time: 30-40 minutes.

2. Place the cabinet back (Ref. No. 1) on a

protected surface to prevent

scratching the paint.

The ange on the

bottom of the back

should be facing upward.

1. The reference numbers used throughout this sheet refer

to the illustration on the back cover. This is to help you

to identify the various parts as they are mentioned.

3. Attach the left side (Ref. No. 2) to the back by placing

ange (A) around the back and bolting together with

seven bolts and nuts (Ref. Nos. 17 & 18). Be sure that the

lances on all shelf adjustment strips (B) are pointing in the

same direction.

5. Attach the right side (Ref. No. 3) to the back in the same manner

as you did in step 3, again, making sure that the ange is

around the back and that the lances on the shelf adjustment

strips are pointed in the same direction as those on the back and

left side. Push the side panel up so the studs in the top go

through the holes in the top

ange of the side and

fasten with three

nuts as in

step 4).

6. Attach the sill (Ref. No. 6) to the sides. Place nuts loosely on each

of the studs and slide the ends of the sill into the slots on both

sides of the unit. Then, securely tighten the nuts.

4. Attach the top (Ref. No. 5) to the unit by sliding the outer

ange over the back of the unit and the side ange on

the top over the side panel. The threaded studs should go

through the holes in the top

ange of the

side and

fasten with

three nuts.

Attach the

back to the

top using four

bolts and nuts.

7. Place the rear ange of the bottom (Ref. No. 7) into the

bottom lances of the back. The ange with two holes should

face the front, hanging over the sill. Insert the bolts through

the bottom and still with the head

facing the front of the unit.

Secure with

two nuts.

All lances point UP on

both backs and side.

Flange goes

under back.

Flange faces upward.

Flanges

face upward

Threaded studs go

through the holes

in the ﬂange at the

top of the side.

Slide ends in to the slots

on the bottom of the sides.

Nuts placed loosely

on studs of the sill.

Insert bottom into

bottom lances.

NOTE: When bolting the unit together, leave

the bolts slightly loose until Step 8, unless

otherwise speciﬁed.

NOTE: All illustrations show a solid door. Assembly

for C-Thru doors (CVD1480) is identical.

Two holes must

be in front

Produkt Specifikationer

Mærke:	Tennsco
Kategori:	Skab
Model:	CVD1480

Har du brug for hjælp?

Hvis du har brug for hjælp til Tennsco CVD1480 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Skab Tennsco Manualer

Tennsco J1878C-N Manual

16 August 2024

Tennsco 1436 Manual

15 August 2024

Tennsco CVD7214 Manual

14 August 2024

Tennsco 7220 Manual

14 August 2024

Tennsco JSD2478SU Manual

12 August 2024

Tennsco CVD1472 Manual

12 August 2024

Tennsco J2478A-N-W Manual

11 August 2024

Tennsco 7814 Manual

10 August 2024

Tennsco 2472 Manual

9 August 2024

Tennsco 1471 Manual

9 August 2024

Skab Manualer

Nyeste Skab Manualer

BDI Mesa 7639 Manual

31 Marts 2025

Ikea KOMPLEMENT 002.463.56 Manual

13 Marts 2025

Ikea KOMPLEMENT 302.463.88 Manual

13 Marts 2025

Ikea SMÅSTAD 905.729.00 Manual

13 Marts 2025

Ikea VITTSJÖ 805.955.44 Manual

13 Marts 2025

Ikea VIHALS 305.951.17 Manual

13 Marts 2025

Ikea SONGESAND 106.054.19 Manual

13 Marts 2025

Ikea SMÅSTAD 504.341.52 Manual

13 Marts 2025

Ikea KAMMARTORP 005.746.68 Manual

13 Marts 2025

Ikea KAMMARTORP 605.746.65 Manual

13 Marts 2025