SUGGESTED GALLEY TAP PLACEMENT GUIDE
Suggested maximum inside corner radius of countertop cutout 3/8”
Galley Tap 1 3/8” minimum to 1 1/2" maximum hole diameter
Center Tap hole diameters 2” behind cutout
Note: Galley Hot & Cold Tap requires a minimum 8" clearance to center if installed to the right of the Galley Tap
Note: Tap Placements are for right hand or left hand drain orientation
Call 800.375.4255 or email customerservice@thegalley.com
for additional guidance on Tap and Tap Accessory placements
O.D. 22” (559 mm)
I.D. 20 1/2” (521 mm)
I.D. 17” (432 mm)
C.O. 21” (533 mm)
10 1/2” (267 mm)10 1/2” (267 mm)
IWS 2C / IWA 2C / IBS 2C
O.D. 27 1/2” (698.5 mm)
I.D. 26” (660 mm)
I.D. 17” (432 mm)
C.O. 26 1/2” (673 mm)
13 1/4” (337 mm)13 1/4” (337 mm)
IWS 30S / IWA 30S
O.D. 33 1/2” (851 mm)
I.D. 32” (813 mm)
I.D. 17” (432 mm)
C.O. 32 1/2” (826 mm)
16 1/4” (413 mm)16 1/4” (413 mm)
IWS 3S / IWA 3S
O.D. 45 1/2” (1156 mm)
I.D. 44” (1118 mm)
I.D. 17” (432 mm)
C.O. 44 1/2” (1130 mm)
22 1/4” (565 mm)22 1/4” (565 mm)
IWS 4S / IWA 4S
8” (203 mm)
C.O. 18” (457 mm)
O.D. 19 1/2” (495 mm)
C.O. 18” (457 mm)
O.D. 19 1/2” (495 mm)
8” (203 mm)
8” (203 mm)
8” (203 mm)
O.D. 57 1/2” (1461 mm)
I.D. 56” (1422 mm)
I.D. 17” (432 mm)
C.O. 56 1/2” (1435 mm)
18” (457 mm)19 1/4” (489 mm) 19 1/4” (489 mm)
IWS 5S
C.O. 18” (457 mm)
O.D. 19 1/2” (495 mm)
C.O. 18” (457 mm)
O.D. 19 1/2” (495 mm)
8” (203 mm)
8” (203 mm)
8” (203 mm)
8” (203 mm)
O.D. 69 1/2” (1765 mm)
I.D. 68” (1727 mm)
I.D. 17” (432 mm)
C.O. 68 1/2” (1740 mm)
24” (610 mm)22 1/4” (565 mm) 22 1/4” (565 mm)
IWS 6S
C.O. 18” (457 mm)
O.D. 19 1/2” (495 mm)
C.O. 18” (457 mm)
O.D. 19 1/2” (495 mm)
8” (203 mm)
8” (203 mm)
10 1/4”
(260 mm)
8” (203 mm)
O.D. 81 1/2” (2070 mm)
I.D. 80” (2032 mm)
I.D. 17” (432 mm)
C.O. 18” (457 mm)
O.D. 19 1/2” (495 mm)
C.O. 80 1/2” (2045 mm)
30” (762 mm)25 1/4” (641 mm) 25 1/4” (641 mm)
8” (203 mm)
8” (203 mm)
IWS 7S
1
18” Finished cutout
1/2” Reveal front
and back
10”
16”
Side view applies to all
Workstations
Workstations
Right Hand Drain Orientation
