Thorma Alicante Manual

Thorma Pejs Alicante

Læs gratis den danske manual til Thorma Alicante (29 sider) i kategorien Pejs. Denne vejledning er vurderet som hjælpsom af 11 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 6 anmeldelser. Har du et spørgsmål om Thorma Alicante, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/29
ALICANTE / VALENCIA
Installation and operation manual solid fuel fireplace insert
GB
ALICANTE, VALENCIA
tested according to the standard EN 13229
1. Installation manual
1.1 General
Fireplace insert for solid fuel is a single-shaft heating device which replaces the existing heating for short periods between seasons or
supports it in the cold seasons. Fireplace insert is designed for local heating. Fireplace insert can be installed in a normal environment.
This fireplace insert has been tested according the standard EN 13229 with fuels: wood and brown-coal briquettes. This fireplace
insert met the requirements of this standard.
All local regulations, including regulations relating to national and European standards have to be followed when installing the fireplace
insert.
Before mounting the fireplace insert, you have to inform the competent master chimney sweep who will inspect as expert the proper
connection of fireplace insert to the chimney. Fireplace insert must be installed on floorings that have corresponding loading capacity.
By installation, it is necessary to ensure sufficient space for cleaning of fire insert, flue and chimney. The fire insert must be closed
during operation, but also when not in operation, because otherwise it might significantly affect other devices connected to the
chimney.
Combustion chamber is enclosed by sheet metal plate filled from inside with vermiculittes. In the bottom part of the combustion
chamber, there is the bed with cast-iron grate. There is an ash box under the grate. Stokers door are sealed with gasket. The door may
be opened only to add fuel. The stokers door are paned with highly heat-resistant glass-ceramic.
The smallest size of the front opening in the lining of fireplace insert is: width 600 mm and height 750 mm. Surface temperatures of the
lining can reach, depending on thermal resistance coefficient of the used construction material and its thickness, within the range
between 30 and 80°C.
NOTE: when claiming or ordering spare parts always quote the name, type and serial number given on the data card.
1.2 Specifications
Nominal capacity: 8,0 kW
Nominal heating capacity efficiency: wood = 82,3 %, lignite briquettes = 70,5 %
Operating chimney draft: 10 Pa
Height with legs 825 mm
Width
588 mm
Depth ALICANTE = 392 mm, VALENCIA =423 mm
Draught shaft diameter: Ø150 mm
Weight ALICANTE = 63 kg, VALENCIA = 64 kg
Recommended fuel:
- dry hard wood - approximate heating value 15 MJ.kg
-1
- lignite briquettes - approximate heating capacity 20 ÷ 23 MJkg
-1
Approximate consumption of recommended fuel at nominal capacity:
- wood: 2.2 kg.hod.
-1
- lignite briquettes: 1.7 kg.hod.
-1
Heating capacity:
- favourable type of construction: 190 m³
- less favourable type of construction: 145 m³
- unfavourable type of construction: 98 m³
Applicable standards: EN 13229
1.3 Connection to the chimney
At installation comply with all corresponding project, safety and hygienic regulations.
Data to calculate the chimney (at the nominal thermal power):
Fuel Brown-coal briquettes Wood
Flue gas flow [g/s] 10,0 6,1
Max. flue gas temperature behind exhaust throat [°C] 377 312
Min. blast draught at nominal thermal power [Pa] 10 10
The fireplace insert can be used to connect a multi-occupied chimney, which means that to the chimney with the fire insert connected,
we can connect more devices.
Before connecting the fireplace insert, make sure there is sufficient blast in the chimney. Flame of a burning paper or candle should be
sucked into the chimney opening. The fireplace insert should be attached to the chimney flue in the shortest direction.
The fireplace insert should be attached to the chimney flue always with the consent of competent chimney sweeper office in
compliance with STN 73 4210 and STN 73 4201.
If the fireplace insert cannot be attached to the chimney flue directly, the flue involved should be the shortest possible and ascend
towards the chimney. Flues can be of maximum 1,5 m length. In any case, it is necessary to ensure smoke tubes and bends, mounted
on exhaust throat, against getting loose by a pin. Smoke tubes and bends must be attached firm and tight to the fireplace insert and
plugged into each other by minimum 40 mm length in the direction of chimney blast. The chimney opening must be fitted with a sheet
metal case with a diameter corresponding to the diameter of used smoke tubes.
C t d i t ti f fi l i
t t th hi i di l d i Fi 1

Produkt Specifikationer

Mærke: Thorma
Kategori: Pejs
Model: Alicante

Har du brug for hjælp?

Hvis du har brug for hjælp til Thorma Alicante stil et spørgsmål nedenfor, og andre brugere vil svare dig


Pejs Thorma Manualer

Thorma

Thorma Alicante Manual

16 Juni 2024

Pejs Manualer

Nyeste Pejs Manualer

Firefriend

Firefriend DF-6507JU Manual

28 December 2025
Blumfeldt

Blumfeldt Fiamme Camino Manual

8 December 2025
Dimplex

Dimplex CAS500R Manual

7 December 2025
Klarstein

Klarstein Zermatt 1800W Manual

2 December 2025
Klarstein

Klarstein Phantasma Skyfire Manual

28 November 2025
Klarstein

Klarstein Phantasma Futur Manual

27 November 2025
Klarstein

Klarstein Elbrus Manual

27 November 2025
Klarstein

Klarstein Feuerschale Manual

26 November 2025
Klarstein

Klarstein Phantasma Peña Manual

26 November 2025
Klarstein

Klarstein Zermatt Manual

26 November 2025