TOA SR-SA3 Manual

TOA Ikke kategoriseret SR-SA3

Læs gratis den danske manual til TOA SR-SA3 (1 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 47 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 24 anmeldelser. Har du et spørgsmål om TOA SR-SA3, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

INSTALLATION MANUAL

STAND ADAPTER SR-SA3

The SR-SA3 is a Stand Adapter designed to install the Line Array

Speaker SR-H2L, SR-H2S, SR-H3L, or SR-H3S on the ST-33B

Speaker Stand.

2. SPECIFICATIONS

Note: The design and specifications are subject to change without

notice for improvement.

133-05-447-70

URL: http://www.toa.jp/

1. SAFETY PRECAUTIONS

3. INSTALLATION (See the figure at right.) 4. HOW TO USE

[About a height limit of the speaker]

[About a conversion cable for speaker cable]

When connecting the speaker cable to the speaker input terminal

via the XLR or Neutrick “Speakon” connector, use a short

conversion cable as shown below, then secure it on the speaker’s

rear with a cable clamp.

• Before installation or use, be sure to carefully read all the

instructions in this section for correct and safe operation.

• Be sure to follow all the precautionary instructions in this section,

which contain important warnings and/or cautions regarding

safety.

• After reading, keep this manual handy for future reference.

WARNING

Indicates a potentially hazardous situation which, if

mishandled, could result in death or serious personal injury.

CAUTION

Indicates a potentially hazardous situation which, if

mishandled, could result in moderate or minor personal injury,

and/or property damage.

Applicable Speaker SR-H2L, SR-H2S, SR-H3L, SR-H3S

Applicable Stand ST-33B

Finish Rolled steel plate, black, paint

Dimensions 62 (w) x 385 (h) x 69 (d) mm

(2.44" x 15.16" x 2.72")

Weight 1.4 kg (3.09 lb)

Accessory Hex bolt M5 x 25 (with washer) ....... 4

The safety precautions in this section apply to the SR-SA3 Stand

Adapter. For precautions relating to other combination products,

refer to the instruction manual enclosed with each equipment.

• Do not use other methods than specified to mount the Stand

Adapter. Extreme force is applied to the unit and the unit could fall

down or off, possibly resulting in personal injuries.

• Ensure that all bolts are securely tightened. If they are not

tightened or firmly secured after installation, the unit could fall

down or off, possibly resulting in personal injury.

• Use the SR-H2L, SR-H2S, SR-H3L, or SR-H3S speaker, and the

ST-33B Speaker Stand in combination. Doing otherwise may

cause the speaker system to fall down or off, resulting in personal

injury.

• Be sure to follow the precautions below when using the speaker

stand. Otherwise, the stand with speaker installed may fall down,

causing personal injury.

· Spread the tripod legs until the stays extend horizontally.

· The height of the speaker's top surface from the floor must be

240 cm (95") or less.

• Avoid touching the unit's sharp metal edge to prevent injury.

[SR-H2L]

SR-SA3

[SR-H2S] [SR-H3L] [SR-H3S]

Stand Adapter mounting position

Hex bolt M5 x 25

(supplied with the SR-SA3)

Note

Remove the attached screws.

The removed screws are not used.

WARNING

When using the speaker stand, the height of the

speaker's top surface from the floor must be 240 cm

(95") or less. Otherwise, the stand may fall down,

causing personal injury.

The height must be 240 cm (95") or less.

(Applicable to all applicable speakers)

Removable input connector

(supplied with the speaker)

Cable clamp

Note

When securing the cable clamp,

never use these 4 screws.

Conversion cable

Note

Prepare the conversion cable and cable clamp separately.

The figure shows an example for installing the SR-H3S.

WARNING

Spread the tripod legs until the stays extend horizontally

and always use the stand in stable condition. If the legs

are not sufficiently spread, this may cause the stand and

mounted speaker to fall down, resulting in personal injury.

Removable input connector

Speaker body

(rear)

Stand Adapter

(SR-SA3)

Hex bolt M5 x 25

(supplied with the

SR-SA3)

Knob bolt

Speaker stand

(ST-33B)

Stay

Note

Only 1 speaker can be installed using the SR-SA3. (Never use the

SR-SA3 to install the linked speakers.)

Step 1. Attach the Stand Adapter to the speaker's rear.

Remove the specified screws on the speaker's rear

surface, then use their screw holes to secure the Stand

Adapter. In this event, the removed screws are not used.

Note

For the Stand Adapter mounting position, refer to the figure

below.

Step 2. Mount the speaker (with the Adapter attached) on

the stand, then securely tighten the Adapter’s

knob bolt.

Notes

• Spread the tripod legs wide apart enough to keep the

stand stable.

• Lower the height of the speaker stand to make

installation work easier.

• For the speaker stand installation, refer to the instruction

manual enclosed with the ST-33B Speaker Stand.

• For the speaker cable connection, refer to the instruction

manual enclosed with the applicable speaker.

Produkt Specifikationer

Mærke:	TOA
Kategori:	Ikke kategoriseret
Model:	SR-SA3
Bredde:	62 mm
Dybde:	69 mm
Vægt:	1400 g
Produktfarve:	Sort
Materiale:	Stål
Kapabilitet:	SR-H3S, SR-H3L, SR-H2S, SR-H2L
Højde (maks.):	385 mm