TOA ST-16A Manual

TOA højttalerstøtte ST-16A

Læs gratis den danske manual til TOA ST-16A (2 sider) i kategorien højttalerstøtte. Denne vejledning er vurderet som hjælpsom af 18 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 9.5 anmeldelser. Har du et spørgsmål om TOA ST-16A, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

ST-16ASPEAKER STAND

INSTRUCTION MANUAL

1. SAFETY PRECAUTIONS

• Before installation or use, be sure to carefully read all the instructions in this section for correct and safe

operation.

• Be sure to follow all the precautionary instructions in this section, which contain important warnings and/or

cautions regarding safety.

• After reading, keep this manual handy for future reference.

2. HOW TO USE

Step 1. Attach the bracket to the speaker as shown below.

Attach the bracket to the speaker

Indicates a potentially hazardous situation which, if mishandled, could

result in death or serious personal injury.

WARNING

• Do not mount the speaker of 7 kg or more. The stand or its internal pipe may fall down or drop, resulting in

personal injury. Even though the speaker weight is below 7 kg, do not use that speaker if the stand is made

unstable.

• Do not extend the internal pipe beyond the MAXIMUM point marked in red. Doing so may make the stand

unstable, and cause the stand or its internal pipe to fall down or drop, resulting in personal injury.

• Avoid installing the stand in the following locations. Otherwise, the mounted speaker may drop or the stand

may fall, resulting in personal injury.

· Doorway or other high traffic area where people may trip on the stand.

· Locations where the unit is exposed to a strong wind.

· Unstable locations, such as on a rickety table or a slanted surface.

Important: Even in locations other than the above, if the unit may fall down, take appropriate fall preventive

measures.

• When adjusting the stand height with the speaker mounted, hold the speaker firmly. Doing otherwise may

cause the stand to fall, resulting in personal injury and/or property damage.

• Fully expand the legs. If the legs are not fully expanded, the stand may fall down, resulting in personal injury.

Attachment to the horn speaker Attachment to the FGM speakerAttachment to the megaphone

Butterfly nut

Washer

Hexagon bolt

Insert the hexagon bolt into the hexagonal

hole located inside the bracket and tighten

the bolt to attach the bracket.

Hexagon bolt

Insert the hexagon bolt into the hexagonal hole

located inside the bracket and tighten the bolt

rotating the bracket in the direction of the arrow

to secure the bracket.

Spacer

Be sure to use the spacer.

If not used, the thread in the

megaphone may be destroyed.

Note

Do not use this spacer for the

megaphones ER-2230W and

WR-2930W.

Speaker

mounting screw

Bracket

Step 2. Loosen the leg locking knob to fully expand the legs. Lowering the slide leg adjustment till it hits the

stopper in the center of the external pipe permits maximum leg expansion.

Step 3. Tighten the leg locking knob to secure the legs.

Step 4. Loosen the internal pipe locking knob to raise the internal pipe to the desired height.

Step 5. Tighten the internal pipe locking knob to secure the pipe.

Step 6. Insert the bracket onto the top of the internal pipe, and mount the speaker on the stand.

Step 7. After determining the orientation of the speaker, secure the speaker by tightening the bracket fixing

knob.

Note: After installation completion, ensure again that every knob is tightened.

Step 8. After use, reverse the procedures 1 – 7 above to detach the speaker and fold the stand.

Note: Be sure to fold the stand after detaching the speaker from the stand.

[Storing mounting screws]

Speaker mounting screws for installing the FGM speakers can be stored

by mounting them into the storage holes provided in the bracket.

Use these holes to prevent the loss of screws while putting away the

equipment.

Put away the stand after use

Mount the speaker on the stand

Put up the stand

1130 – 1660 mm

1050 mm

Speaker mounting screw

(M5 x 20) x 2

Hexagon bolt

(M8 x 20) x 1

Washer x 1

Spacer x 1

Butterfly nut x 1

Weight: 1.7 kg (bracket included)

Bracket

Slide leg

adjustment

External pipe

Stopper

Stay

Bracket fixing knob

Internal pipe

locking knob

Leg locking knob

Bracket

Bracket fixing

knob

Internal pipe

locking knob

External pipe

Leg locking

knob

Stopper

Slide leg adjustment

Leg

Stay

Speaker mounting

screw

Bracket

Screw storage hole

3. PART NAMES

Stand (when in use)Stand (when folded)Accessory

Produkt Specifikationer

Mærke:	TOA
Kategori:	højttalerstøtte
Model:	ST-16A

Har du brug for hjælp?

Hvis du har brug for hjælp til TOA ST-16A stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

højttalerstøtte TOA Manualer

TOA ST-16A Manual

20 Juli 2024

højttalerstøtte Manualer

Nyeste højttalerstøtte Manualer

Sonorous SP 600 Manual

27 Februar 2025

Axis TC1601 Manual

20 Februar 2025

SoundTube SM1290 Manual

20 Februar 2025

Nubert BS-652 Manual

5 Februar 2025

NeoMounts NS-SHELF100 Manual

14 Januar 2025

Sonos Arc Ultra Wall Mount Manual

14 Januar 2025

Omnitronic STS-1 Manual

31 December 2025

Omnitronic EUMO-2 Manual

31 December 2025

Konig & Meyer 24496 Manual

30 December 2025

Bowers Wilkins FS-700 S3 Manual

30 December 2025