TP-Link EAP110-Outdoor V3 Manual

TP-Link Adgangspunkt EAP110-Outdoor V3

Læs gratis den danske manual til TP-Link EAP110-Outdoor V3 (4 sider) i kategorien Adgangspunkt. Denne vejledning er vurderet som hjælpsom af 15 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 8 anmeldelser. Har du et spørgsmål om TP-Link EAP110-Outdoor V3, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Indoor/Outdoor Access Point

Overview

Package Contents

Panel Layout

Power LED:

On: Power on

Off: Power off

Note: EAP225-Outdoor does not support the Remote Reset feature.

Passive PoE Adapter

Remote Reset:

Press and hold for about 8 seconds until

the LED is quickly flashing yellow then

green. The EAP will restore to factory

default settings.

LED Status Indication

Solid green The device is initializing or working properly.

Flashing yellow System errors. RAM, Flash, Ethernet, WLAN or

rmware may be malfunctioning.

Flashing yellow, green Firmware update is in progress. Do not disconnect

or power o the device.

Quickly ashing yellow, green The device is being reset to its factory default

settings.

Flashes green twice Initialization is completed.

SYS LED Explanation

Flashing green slowly

(Only for EAP225-Outdoor) The device is in an isolated state.

Lightning and ESD Protection

Before mounting the EAP, you should consider Lightning and ESD

Protection to ensure safety.

Proper grounding is extremely important for outdoor devices. By using a

shielded CAT5e (or above) cable for connection, you can reduce the

damage of ESD attacks.

Hardware Installation

Mount the EAP

The EAP can be pole-mounted or wall-mounted. Follow the steps below

for the appropriate installation.

Option 1: Pole Mounting

Lead the end of the pole mounting strap

through the back of the EAP.

Step 1:

Position the EAP and wrap the pole

mounting strap around the pole. Feed the

end through the screw-block and tighten

the strap until the EAP is secure.

Step 2:

Option 2: Wall Mounting

Step 1:

Place the mounting bracket (for EAP) in

the right position. Mark two positions

for the screw holes .

Drill two 6 mm holes for the screws at

the marked positions.

Step 2:

Insert the plastic wall anchors into the 6

mm holes. Align the bracket (for EAP) to

the plastic wall anchors and drive the

self-tapping screws into the anchors

through the bracket (for EAP).

Step 3:

Align the mounting tabs on the back of

the EAP with the slot of the mounting

bracket (for EAP). Push and slide the

EAP downward until it locks into place.

3Connect Cables

Firmly grasp the rear of the interface

cover and pull it downward.

Step 1:

Use an adequate Ethernet cable to

connect the LAN port. The length of

cable is up to 100 m for steady power

supply. Shielded CAT5e (or above) cable

is recommended.

Step 2:

Step 3:

Attach the waterproof rubber insert to the

groove at the underside of the device for

waterproong. Move the Ethernet cable to

the hole of the waterproof rubber insert.

Flatten the waterproof rubber insert until

it gets parallel to the device. Replace the

cover until it rmly locks into place.

Step 4:

EAP

Grounded PoE Adapter

Shielded CAT5e (or above)

Cable

Grounded 3-wire

Power Outlet

RESETShielded Ethernet

Port LAN

Passive PoE Adapter

(Mounting Bracket Included)

Power Cord

M3×28 Plastic Wall

Anchors (Qty.4)

M3×20 Self-tapping

Screws (Qty.2)

EAP

Antennas (Qty.2)

Mounting Bracket

(for EAP)

Installation Guide

Pole Mounting StrapWaterproof Rubber

Insert

M3×16 Self-tapping

Screws (Qty.2)

Connect the antennas to the EAP. For

optimal Wi-Fi performance, adjust the

direction of the antennas. It is recom-

mended to position the antennas at

45-degree angles.

Step 3:

Step 4:

Connect the antennas to the EAP. For

optimal Wi-Fi performance, adjust the

direction of the antennas. It is recom-

mended to position the antennas at

45-degree angles.

Quick Installation Guide

Setup with videos

Visit https://www.tp-link.com/support/setup-video/ or scan the QR

code to search for the setup video of your product model.

Produkt Specifikationer

Mærke:	TP-Link
Kategori:	Adgangspunkt
Model:	EAP110-Outdoor V3

Har du brug for hjælp?

Hvis du har brug for hjælp til TP-Link EAP110-Outdoor V3 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Adgangspunkt TP-Link Manualer

TP-Link Omada EAP772 Manual

7 September 2025

TP-Link RE800BE Manual

19 August 2025

TP-Link Festa F61-Outdoor Manual

16 August 2025

TP-Link Festa F76 Manual

16 August 2025

TP-Link EAP723 Manual

16 August 2025

TP-Link Festa F52-Outdoor Manual

16 August 2025

TP-Link Omada EAP215-Bridge KIT Manual

12 August 2025

TP-Link Omada Pro AP9778 Manual

25 Juli 2025

TP-Link Omada Pro AP9665 Manual

25 Juli 2025

TP-Link Omada EAP223 Manual

25 Juli 2025

Adgangspunkt Manualer

Nyeste Adgangspunkt Manualer

EtherWAN EW75200 Manual

4 November 2025

D-Link DBR-X3000-AP Manual

1 November 2025

Draytek VigorAP 700 Manual

19 Oktober 2025

Lancom LN-860 Manual

16 Oktober 2025

Mikrotik SXT 5 ac Manual

15 Oktober 2025

Lancom LX-7400 Manual

8 Oktober 2025

Draytek Vigor AP 1000C Manual

7 Oktober 2025

Conceptronic C150APM Manual

7 Oktober 2025

Draytek VigorAP 910C Manual

6 Oktober 2025

Draytek VigorAP 1062C Manual

6 Oktober 2025