Traxxas EZ-Peak Dual Manual

Traxxas Batterioplader EZ-Peak Dual

Læs gratis den danske manual til Traxxas EZ-Peak Dual (4 sider) i kategorien Batterioplader. Denne vejledning er vurderet som hjælpsom af 53 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 27 anmeldelser. Har du et spørgsmål om Traxxas EZ-Peak Dual, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

NiMH/LiPO DUAL CHARGER INST RUCT IONS

Covers Part #2972X

Thank you for purchasing the Traxxas EZ-Peak Dual charger.

This charger features exclusive Traxxas innovations that make

charging batteries easier and safer than ever. If you have any

questions or concerns about your charger, please contact our

customer support team for fast, friendly answers and solutions.

Contact information is at the bottom of this page.

WARNING! For best charging results and your safety, it is essential that you read and

understand these instructions, warnings, and precautions before using the charger.

Charging and discharging batteries has the potential for serious injury and damage

to property. Use care when charging and follow all instructions and cautions. A

Charge

Status

iD LogoBattery Type

Traxxas High-Current

Connector

Charge

Progress

Charge Rate

(Amps)

G G

*Note: Either charger output port can be used independently or both ports can be used

simultaneously to charge. Use the buttons corresponding with the chosen port(s) to

operate the charger.

1. Plug the charger into an AC wall outlet

and connect the battery/batteries

2. Verify the charge settings

Charging Traxxas iD NiMH Batteries

Battery type selected must match the battery type shown on the battery.

The charger will recognize the iD batteries

and show you the charge settings.

Charge Rate StartBattery Type

HKC18031-R02 180808

T R A X X A S . c o m

Traxxas, 6250 Traxxas Way, McKinney, TX 75070,

Phone: 1-888-TRAXXAS (Toll-free, US only) or 972-549-3000, Fax: 972-549-3011, e-mail: support@Traxxas.com

3. Charging

Press and hold the Start button(s)

for 1 second. The charger will

play a tone, indicating that

charging has started. Press once

to stop. The charger will play a

tone, indicating that charging

has been canceled. The charge

progress LEDs will light as the

battery charges.

Charging

(flashing)

Charge Cycle Progress

4. Charge cycle complete

The charger will play a complete tone, followed by one or two beeps

to indicate channel 1 (left) or channel 2 (right) charging is complete.

The EZ Peak Dual will

trickle charge your NiMH

battery at up to 200mA

for 12 hours after the

charge cycle is complete.

Cycle

Complete

(solid)

A. Start/Stop

B. LiPo Charge Mode Select

C. Battery Type Select

D. Charge Rate Select

E. Charger Output Ports (Traxxas

High-Current Connector)*

F. 2S/3S Lipo Balance Ports

(pull to remove cover)

G. Charge Status LEDs

H. Charge Progress/

Charge Rate LEDs

Identifying iD Batteries LiPo battery shown, NiMH battery similar

Dual Charge Mode

Charging Traxxas iD LiPo Batteries

Fast charge

Fast charges batteries without

balancing your cells. Stops charging

when the ﬁrst cell reaches peak voltage.

Depending on the condition of the

batteries, this may reduce the charge

time by a few minutes.

Balance charge

Always balance charge your LiPo

batteries for maximum capacity,

voltage, and battery life. This is the

default setting for Traxxas iD batteries.

The EZ-Peak Dual performs a balance

charge quickly and efﬁciently.

LiPo Charging M

Storage charge

Makes it easy to charge or discharge

batteries to the proper storage

voltage. Use this mode whenever

batteries will be stored unused for

more than 7 days.

Change your LiPo charging mode if desired.

The default setting for iD LiPo batteries is Balance Charge.

Charging Traxxas iD Batteries

in High Output Mode

High Output Mode allows you to charge high capacity batteries

at a faster charge rate. Use the high output channel to charge your

5000 mAh NiMH batteries at 5 amps and your 4000 mAh and larger

LiPo batteries at a “2C” charge rate (2C is 2 times the capacity; 4000

mAh x 2 = 8000 or 8 amps). Only one Traxxas battery at a time can be

charged in High Output Mode using the output port on the right side

of the charger (the left side of the charger is disabled).

Move the switch

to High Output, and follow steps 1-4 for Traxxas iD battery charging.

Note: The 5A LED will light to indicate the charge rate setting for Traxxas

Power Cell batteries requiring a charge current of 5 amps or less.

4. Charge cycle complete

The charger will play a complete tone, followed by one or two beeps to

indicate channel 1 (left) or channel 2 (right) charging is complete.

1. Plug the charger into an AC wall outlet

and connect the battery/batteries

The charger will recognize the iD batteries

and show you the charge settings.

2. Verify the charge settings

Battery type selected must match the battery type shown on the battery.

3. Charging

Press and hold the Start button(s) for 1 second. The charger will play a

tone, indicating that charging has started. Press once to stop. The charger

will play a tone, indicating that charging has been canceled. The charge

progress LEDs will light as the battery charges.

Charging

(flashing)

Charge Cycle Progress

Cycle

Complete

(solid)

Disabled

Start

Charge Mode

(the default is

Balance) Charge RateBattery Type

Dual Charge Mode

Produkt Specifikationer

Mærke:	Traxxas
Kategori:	Batterioplader
Model:	EZ-Peak Dual
Type:	Indendørs batterioplader
Bredde:	176 mm
Dybde:	138 mm
Højde:	57 mm
Vægt:	575 g
Produktfarve:	Flerfarvet
Udgangsstrøm:	8 A
Antal understøttede batterier:	2
Indgangsspænding:	100-240 V
Indgangsfrekvens:	- Hz
Kompatible batteri-teknologier:	Lithium Polymer (LiPo), Nickel-Metal Hydride (NiMH)