Trumeter 7922 Manual

Trumeter Måleudstyr 7922

Læs gratis den danske manual til Trumeter 7922 (40 sider) i kategorien Måleudstyr. Denne vejledning er vurderet som hjælpsom af 14 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 7.5 anmeldelser. Har du et spørgsmål om Trumeter 7922, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/40

019510-01 Issue 1.1 03/2007

7922

6 digit programmable bi-directional counter relay, with

dual preset or batch mode operation, prescaling and

EEPROM data storage

6-Stelliger Bi-Direktionaler Zähler mit Supertwist-LCD

mit Einzel/Doppel- und Chargen Vorwahl, Skalierung

durch Vorteiler und EEPROM-Datenspeicherung

Compteur bidirectionnel à 6 chiffres, programmable,

avec 2 présélections ou 1 présélection et comptage de

lots, facteurs d'échelles et mémoire EEPROM

Relé contador bidireccional programable de 6 dígitos,

con modos de operación de doble preselección o de

lotes, pre-escala y almacenado de datos en EEPROM.

Contatore a relè a 6 cifre bidirezionale programmabile,

con funzionamento in doppia modalità preimpostata o

batch, prescala e memorizzazione dati nella EEPROM

Diagrams, Abbildungen, Diagrammes,

Diagramas, Diagrammi

English

Page 2

Deutsch

Seite 8

Français

Page 14

Español

Página 20

Italiano

Pagina 26

Page 35

Seite 35

Pagina 35

WARNING: Read page 32 first.

ACHTUNG: Lesen Sie zuerst Seite 32!

RECOMMANDATION IMPORTANTE:

Reportez-vous tout d'abord à la page 33

ATENCIÓN: Primero lea la página 33

ATTENZIONE: Leggere prima la pagina 34.

Specification

Display

Black on green STN LCD, with yellow/green LED

backlight.

Program Storage

Erase/write cycles:1,000,000

Life: 40 years min

Count Range

-99999 to 999999

Count Pre-scaler

Multiplier 0.00250 to 9.99999

Divider 1 to 99999

External Reset response time

Max 2ms

Count Inputs

High Speed: 10kHz max (electronic)

(Dividing prescaler: 7kHz max)

Duty cycle: 60:40 max

Low Speed: 30Hz max (contact closure)

Relay Contacts

5A resistive load 100,000 operations

2A resistive load 1,000,000 operations

Reaction time: <20ms.

P1 Relay: UL Ratings

AC 250V max, DC 125V max

250VAC 1/6 HP

30VDC 5A

P1 Relay: General ratings

AC 1250VA max 300V AC

250Vac (cosø =1): 5A

250Vac (cosø =0.4): 3A

DC 150W max 220V DC

30Vdc: 5A

P2 Relay: UL Ratings

AC 250V max, DC 125V max

250VAC 1/6 HP

30VDC 5A

P2 Relay: General ratings

AC 2000VA max 300V AC

250Vac (cosø =1): 8A

250Vac (cosø =0.4): 5A

DC 150W max 220V DC

30Vdc: 5A

Supply (see Connections)

94 to 240V AC ± 10% 50/60Hz

VA Rating 4VA

or 12 to 24VDC ± 10%

typical current 100mA DC (max)

Installation Category (IEC 664)

Overvoltage category II

(Pollution degree 2)

Operating temperature

-10°C to +60°C

Storage temperature

-20°C to +70°C

Environmental protection

IP65 (panel mounting) using the sealing gasket

supplied (without Screw-fixed bezel). If the seal is

removed, it must be replaced with a new one.

See page 39 for cut-out dimensions

Altitude

Up to 2000m

Relative Humidity

80% max up to 31°C, decreasing to 50% max at

40°C

The front panel buttons are used to program the counter and to display and set the P1

and P2 presets. All the buttons can be disabled by the Keyboard Inhibit input. (see

Programming, page 6).

Auto Reset (see and on page 35)

When Auto Reset is on, the counter will be automatically reset as follows:

In Reset to Zero mode, the counter will reset to zero when P1 is reached.

In Reset to P1 mode, the counter will reset to P1 when zero is reached.

Front Panel Reset and External Reset (RST / Ext. Reset)

A Reset can be caused by pressing the RST button or by applying a signal to the

External Reset input. Any active relay will be returned to its normal condition.

If the operation of the External Reset is safety critical, it is recommended that the External

Reset signal is derived from an independent power supply which will remain stable if the

7922’s supply is interrupted.

P1 and P2 Presets

The minimum value possible for P1 and P2 is 000001,except in Dual Preset

mode, when P2 can be set to zero. P1 and P2 must be greater than any

The Front Panel Count

P1 or P2 or

Batch Total

Digit 1

Multiplying Prescaler

Dividing Prescaler

Select

Program

Reset

P1 Relay state

P2 Relay operated

P1 Relay operated

Digit 6

Produkt Specifikationer

Mærke:	Trumeter
Kategori:	Måleudstyr
Model:	7922

Har du brug for hjælp?

Hvis du har brug for hjælp til Trumeter 7922 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Måleudstyr Trumeter Manualer

Trumeter HED261 Manual

30 August 2024

Trumeter APM-VOLT Manual

30 August 2024

Trumeter APM-RATE Manual

30 August 2024

Trumeter APM-PROC Manual

30 August 2024

Trumeter APM-AMP Manual

30 August 2024

Trumeter APM-M Manual

30 August 2024

Trumeter APM-CT Manual

30 August 2024

Trumeter APM-FREQ Manual

30 August 2024

Trumeter APM-TEMP Manual

30 August 2024

Trumeter 3410 Manual

30 August 2024

Måleudstyr Manualer

Nyeste Måleudstyr Manualer

3 April 2025

3 April 2025

3 April 2025

3 April 2025

3 April 2025

3 April 2025

3 April 2025

3 April 2025

3 April 2025

3 April 2025