Tube-Tech CL 1B Manual

Tube-Tech Ikke kategoriseret CL 1B

Læs gratis den danske manual til Tube-Tech CL 1B (9 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 9 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 5 anmeldelser. Har du et spørgsmål om Tube-Tech CL 1B, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/9
LYDKRAFT ApS
Mose Allé 20, DK 2610 Rødovre
Denmark
1
TUBE-TECH CL 1B
Compressor
DESCRIPTION.
The TUBE-TECH compressor CL 1B differs from many other compressors, in that the gain-
reduction element is made from a non-semiconductor element, which in itself has a very low
harmonic distortion and none of the non-linearity problems involved when using most
semiconductor elements. Furthermore there is no long-term degradation of the element thus
giving it almost infinite life. This element is placed after the input-transformer of the compressor
and followed by an all tube-based amplifier with a gain of -
dB to +30 dB.
Thus the signal is not fed through any semiconductor circuitry on its way to the output.
The amplifier consists of two tubes (valves) in push-pull configuration (one ECC 83 as the
pre-amp and phase splitter, and one ECC 82 as the output stage), and an output transformer.
The power supply for the pre-amp and phase splitter are stabilized and the heaters of both
tubes (valves) are fed with a stabilized DC voltage.
The whole amplifier (including input and output transformer) and the power supplies are placed
on one PC-board.
Both input and output are balanced (600
) and fully floating.
The in/out key switches the compressor in and out without clicks.
THE SIDECHAIN:
The side chain is the only part of the compressor that contains semiconductors. They are used
for three reasons: First they do not affect the sound reproduction, second they have a high slew
rate, which is of importance for the performance of the compressor and third they don't take up
much room.
It contains two J-FET quad op-amps, one npn-transistor and one FET-transistor, which handles
the signal for the gain-reduction element.
The compressor contains two time constants circuits:
1. Fixed attack and release times
2. Variable attack and release times
The
attack/release select
switch makes it possible to use these two circuits separately or
combine their functions.
This gives a feature not normally obtained in other compressors:
In the combined (fix. /man.) state the attack- and release controls makes it possible to
obtain a complex release-time slope. (See page 4)
(980112)
LYDKRAFT ApS
Mose Allé 20, DK 2610 Rødovre
Denmark
2
COMPRESSOR INTERCONNECTION:
The side chain sockets for interconnection of several compressors are located on the rear
panel.
A switch (BUS SELECT) on the front selects which compressors are interconnected, and on
which bus they are connected. If you e.g. have 10 compressors in a rack, you can select
compressor 1,5,7 and 8 on bus 1, and compressor 2,3,6 and 9 on bus 2, leaving compressor 4
and 6 in the off position.
Compressors 1,5,7,8 are now interconnected and all four will perform the exact same
compression. This applies to compressor 2,3,6 and 9 as well. Compressor 4 and 6 are
independent.
The interconnection implies, that the unit, which performs the most compression, is controlling
the others.
To choose which one you want to control, select the attack/release time, the threshold and the
ratio on that unit, and turn the threshold fully counter clockwise on the reminding compressors.
It is of course possible to have all the interconnected compressors control each other
simultaneously.
NB:
Remember to set the ratio control and the gain control in the same position on the
"slaves". Otherwise the stereo image could be shifted during compression. The
attack/release-control on the slaves will have no effect.
The input/output capability of the side chain-circuit allows up to
ten
compressors to be linked
together.
They are connected in parallel with a standard 1/4" stereo jack/-jack cord (tip: bus 1, ring: bus
2).
The two jack socket on the rear panel is connected in parallel and both are input/output.
(980112)

Produkt Specifikationer

Mærke: Tube-Tech
Kategori: Ikke kategoriseret
Model: CL 1B

Har du brug for hjælp?

Hvis du har brug for hjælp til Tube-Tech CL 1B stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Tube-Tech Manualer

Tube-Tech

Tube-Tech CL 1B Manual

31 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Miele

Miele WTV 511 Manual

10 Oktober 2025
Miele

Miele WTV 601 Manual

10 Oktober 2025
Miele

Miele GaLa-S Manual

10 Oktober 2025
TOA

TOA HS-150B Manual

10 Oktober 2025
Oras

Oras Saga 3970 Manual

10 Oktober 2025
TOA

TOA AT-4030B-EB Manual

10 Oktober 2025
TOA

TOA VX-030DA Manual

10 Oktober 2025
TOA

TOA RS-481 Manual

10 Oktober 2025
TOA

TOA AT-4200B-EB Manual

10 Oktober 2025
Xerox

Xerox DocuShare Manual

10 Oktober 2025