Uni-T UT30H Manual

Uni-T Termometer UT30H

Læs gratis den danske manual til Uni-T UT30H (1 sider) i kategorien Termometer. Denne vejledning er vurderet som hjælpsom af 28 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 14.5 anmeldelser. Har du et spørgsmål om Uni-T UT30H, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

P/N:110401109418X

PREFACE

Thank you for purchasing the new infrared thermometer. In order to use this product safely and

correctly, please read this manual thoroughly, especially the part. After reading Safety Instructions

this manual, it is recommended to keep the manual at an easily accessible place, preferably close

to the device, for future reference.

LIMITED WARRANTY AND LIABILITY

Uni-Trend guarantees that the product is free from any defect in material and workmanship within

one year from the purchase date. This warranty does not apply to damages caused by accident,

negligence, misuse, modification, contamination or improper handling. The dealer shall not be

entitled to give any other warranty on behalf of Uni-T rend. If you need warranty service within the

warranty period, please contact your seller directly.

Uni-Trend will not be responsible for any special, indirect, incidental or subsequent damage or

loss caused by using this device.

OVERVIEW

SAFETY INSTRUCTION

Warning:

To use the product properly, please read the following instructions carefully before use:

Warning or Caution Read the manual before use

Dispose the device and accessories properly according to local waste management policy.

Direct current

LCD FUNCTION DESCRIPTION

ACCESSORIES

Battery ----------------------------- 2

Manual ----------------------------- 1

Device ------------------------------ 1

SPECIFICATION

SYMBOLS

FAULT DIAGNOSIS

UT30H Non-contact lnfrared Thermometer (hereinafter referred to as "thermometer"). This product

measures temperature by collecting the infrared thermal radiation energy emitted by target surface.

UT30H has advantages of simple and sanitary operation, quick and accurate measurement. It can

measure temperature precisely within 1s by aiming the detector at target object.

It is not allowed to be used in the presence of a mixture of flammable anesthetic gas, air, oxygen or

nitrous oxide. UT30H is a continuous operating device.

This product is composed of infrared sensor, circuit components, operating buttons and plastic shell.

WORKING PRINCIPLE

lnfrared thermometer can measure surface temperature of opaque objects. Its optical device can sense

the infrared energy concentrated on the detector, and the electronic components convert information

into temperature reading which is displayed on the display screen.

OPERATING METHODS

To measure temperature, allow the thermometer aim at the measured target, push the trigger to display

the real time measured result; and loose the trigger to hold it. Thermometer will automatically shut

down if no action were detected out within 15s.

SETTING OPERATION

Symptom

HI (on the screen)

LO (on the screen)

Battery icon flashes

Possible blank screen

Problem

Target temperature exceeding range

Target temperature lower than range

Battery low

Battery drained

Action

Select the target within range

Replace battery

Check and/or replace battery

To ensure safety and accuracy of measurement, only qualified maintenance personnel can repair

it with original components.

Replace the battery immediately once the battery indicator appears.

Prior to using the thermometer, please check the box. If any damage to the thermometer were

found, please do not use it. Inspect for damage or any shortage of parts.

Do not place the thermometer near the objects with high temperature for long period.

It is recommended to operate the thermometer within the environment of 15°C~35°C and RH<85%.

Please use the thermometer indoor and do not expose it to strong sunlight or intense electromagnetic

interference.

Please ensure the temperature around the measuring object is stable, do not test during strong

airflow.

Avoid testing in unstable temperature environment - wait 30min to allow the thermometer to stable.

Wait 10~30min to measure if the measuring object came from very high or very low temperature.

Please wait 10min to measure new objects after measuring very high or very low temperature.

It is recommended to measure thrice for every object and the highest occurring data should be used.

Please accurately aim the sensor window at the measuring target. Otherwise error or HI/LO

indicator will appear.

Please keep the battery out of the reach of children, children may accidentally ingest. Contact with

doctor immediately if that happens.

If the thermometer will not in use for long period, please take out the battery to avoid leakage.

The battery is not allowed to be placed in fire.

Object measurement mode

Body measurement mode

Buzzer

Battery status

Unit of temperature

Measured temperature value

Power On

With thermometer off, short press the trigger to power on, and the last measurement data before shut

down will be displayed after self-inspection.

Power Off

Thermometer will automatically shut down and save the measured value and current serial number

if no action was detected out within 15s.

Temperature Measurement

1. Aim the thermometer at the measured target, press and hold the trigger, the measured temperature

area will be cleared. Then release the trigger, the measured data will be updated.

2. When the measured temperature exceeds 37.2°C, the buzzer will beep.

3. LO displays when the target temperature is lower than the range; displays when the target HI

temperature is exceeding the range. The buzzer will beep when the target temperature is out of the

range

Mode Setting

In the main interface, short press the button to switch between body/object temperature MODE

measurement mode.

Unit Setting

In the main interface, short press the button twice to enter unit setting, short press button SET SEL

to switch the unit between °C or °F.

Buzzer Setting

In the main interface, short press the button thrice to enter buzzer setting interface, and short SET

press button to switch buzzer on or off. SEL

EXTERNAL STRUCTURE

Infrared Sensor

Trigger

LCD

SET Button

MODE Button

SEL Button

Battery cover

FEATURES

White backlight

Option of Celsius/Fahrenheit

Dynamic monitoring of battery capacity

Low voltage indication

Display screen

Sound alarm for the upper and lower temperature limit

MAINTENANCE

BATTERY REPLACEMENT

Measurement Range(Object)

Accuracy (Object)

Measurement Range(Body)

Accuracy (Body)

Resolution

Optimum measuring distance

Unit conversion (°C/°F)

Measurement alarm

Power-on Self-test

Auto shutdown

Backlight

Battery type

Operating environment

Transport and storage environment

Operating atmosphere

0°C 100 32.0 212~ °C ( °F~ °F)

± ± )1.0 2.0°C ( °F

32.0°C-45.0°C 89.6 113.0 ( °F~ °F)

35.0°C 42.0°C: 0.2 0.4~ °C ( °F)±±

32.0°C 34.9°C, 42.1°C 45.0°C: 0.3°C 0.5~ ~ ( °F)± ±

0.1°C

1-5cm

Support

Sound alarm for >37.2°C

Support

1.5V x 2 AAA

15°C~35°C (59 F-95 ), <85%RH° °F

-20°C~60°C (-4 ~140 ), <93%RH°F °F

700hPa-1060hPa

The thermometer is a repeatedly-used accurate device. Please pay attention to clean and

maintenance. Especially keep the lens clean, or the accuracy may be affected.

Clean:

1. Clean chassis: Clean the chassis with cotton sponge or soft cloth with

medicinal alcohol or clean water.

2. Clean lens: Blow away the slipped off grains with clean compressed air.

Wipe the surface carefully with wet cotton swab. Cotton swab should be

moistened with medicinal alcohol or clean water.

If the thermometer will not in use for long period, please take out the

batteries to avoid leakage. Please dispose the waste batteries properly.

Open the battery cover to take out the batteries. Load 2 new AAA batteries

correctly and close the battery cover.

Battery

Produkt Specifikationer

Mærke:	Uni-T
Kategori:	Termometer
Model:	UT30H

Har du brug for hjælp?

Hvis du har brug for hjælp til Uni-T UT30H stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Termometer Uni-T Manualer

3 April 2025

3 April 2025

31 August 2024

31 August 2024

31 August 2024

31 August 2024

31 August 2024

31 August 2024

31 August 2024

31 August 2024

Termometer Manualer

Nyeste Termometer Manualer

14 Juni 2025

14 Juni 2025

14 Juni 2025

14 Juni 2025

14 Juni 2025

13 Juni 2025

13 Juni 2025

13 Juni 2025

CDN ProAccurate FG80 Manual

12 Juni 2025

CDN ProAccurate RFT1 Manual

12 Juni 2025