Valcom Audio Port VIP-804 Manual

Valcom Ikke kategoriseret Audio Port VIP-804

Læs gratis den danske manual til Valcom Audio Port VIP-804 (5 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 46 personer og har en gennemsnitlig bedømmelse på 3.8 stjerner ud af 23.5 anmeldelser. Har du et spørgsmål om Valcom Audio Port VIP-804, eller vil du spørge andre brugere om produktet?

Side 1/5
1 947988
ISSUE 6
VIP-804
QUAD ENHANCED NETWORK AUDIO PORT
INTRODUCTION
The VIP-804 Quad Enhanced Network Audio Port
enables voice access to four zones of one-way
paging over an IP network, allowing page zones
to be extended anywhere network connectivity is
available. The VIP-804 can be programmed as a
SIP (Session Initiation Protocol) device with four
identities (one per audio channel) for connectivity
to virtually any Voice over IP (VoIP) telephone
system.
SPECIFICATIONS
Features
4 Audio Outputs or Inputs
4 Form A relay contacts
4 Contact Closure Inputs
4 SIP identities for registering to a VoIP
telephone system
RJ-45 jack for network connection
Front panel activity LED
Provides audio for up to 40 Valcom one-way
amplified speaker assemblies per zone
Output control contact closure provided
during paging output
Contact closure or VOX operation of audio
inputs
VM-186 RJ-45 Connector provided for
audio and relay interface
Page with music output, music mutes during
page
AUX audio input via RCA jack
Compatible with 25 or 70 Volt amplifiers
2.5mm jack for optional DC power
Power over Ethernet (PoE) 802.3af compatible
Dimensions/Weight
1.75” H x 6.75" W x 9.5" D
(4.45cm H x 17.15cm W x 24.13cm D)
Weight: 1.75 lbs. (0.80 kg)
Nominal Specifications
Input Impedance: 600 Ohms
Input Level: -10dBm nominal
Voice Switch Sensitivity: -21dBm
AUX Input Impedance: 8 to 600 Ohms
AUX Input Level: -10dBm nominal
Output Impedance: 50 Ohms
Output Level: - 10dBm nominal
Relay Current: 1 AMP @ 24VDC
Nominal Power Requirements
Via back panel barrel connector:
Voltage: 24VDC
Current: 325mA
Via 802.3af PoE Ethernet Switch:
802.3af: Class 3
Environment
Temperature: 0 to +40° C
Humidity: 0 to 85% non-precipitating
Packing List
Qty Item
1 VIP-804
1 VSP Document
2 Mounting Brackets W/ Hardware
4 Rubber Pads
4 RJ-45 Patch Cables
4 VM-186 RJ-45 Connectors
2 947988
CAUTION: To reduce the risk of electric shock,
Do not remove cover.
No user serviceable parts inside.
Refer servicing to qualified service personnel.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
This symbol indicates that dangerous
voltage constituting a risk of electric
shock is present within this unit.
This symbol indicates that there are
important operating and maintenance
instructions in the literature accompanying
this unit.
INSTALLATION
Precautionary Designations
FCC Information
This equipment has been tested and found to
comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide
reasonable protection against harmful
interference when the equipment is operated in
a commercial environment. This equipment
generates, uses and can radiate radio
frequency energy and if not installed and used
in accordance with the instruction manual, may
cause harmful interference to radio
communications. Operation of this equipment
in a residential area may cause harmful
interference in which case the user will be
required to correct the interference at his own
expense.
Mounting
The VIP-804 is designed for wall, table or rack
mounting.
Table: Provided with the VIP-804 are four rubber
pads. Peel the pads from their carrier backing
and place at the four corners of the bottom of the
unit.
Wall: Using the template on last page of this
document, mark the location of the bracket screw
holes on the wall. Drill 5/64" pilot holes, 3/4" deep,
at each screw location and use the wood screws
provided to attach the brackets to the wall. For
surfaces other than wood, use hardware
appropriate for the surface (not included). With the
brackets securely attached to the wall, attach the
VIP-804 to the brackets using the included
hardware. Figure 2 illustrates the bracket
assembly.
Rack: Following the assembly drawing, attach the
two mounting brackets to the VIP-804 unit. Using
rack screws, mount the VIP-804 in an available 1U
rack slot. See Figure 1.
Figure 1. Rack Mount
Figure 2. Wall Mount
Power Connections
The preferred method of powering a VIP-804 is via
a Power over Ethernet (PoE) switch meeting the
802.3af specification.
If the rear panel barrel connector is used for power,
the preferred power supply is a Valcom VIP-324D.
Make all required signal connections before
applying power to the unit. If powering via PoE,
make sure all signal connections via the back
panel are made then connect the VIP-804 to the
Ethernet switch.
If power is supplied via the barrel connector, make
sure all signal connections are secure. Attach the
unit to the network via the front panel RJ-45
Ethernet connector. Apply power by plugging the
power supply into the VIP-804 via the barrel
connector on the rear of the VIP-804.


Produkt Specifikationer

Mærke: Valcom
Kategori: Ikke kategoriseret
Model: Audio Port VIP-804

Har du brug for hjælp?

Hvis du har brug for hjælp til Valcom Audio Port VIP-804 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Valcom Manualer

Valcom

Valcom V-9975 Manual

6 September 2024
Valcom

Valcom VIP-802 Manual

6 September 2024
Valcom

Valcom VIP-801 Manual

6 September 2024
Valcom

Valcom S-560 Manual

6 September 2024
Valcom

Valcom VP-12124 Manual

6 September 2024
Valcom

Valcom VIP-998 Manual

6 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer