Valcom V-9975 Manual

Valcom Ikke kategoriseret V-9975

Læs gratis den danske manual til Valcom V-9975 (3 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 40 personer og har en gennemsnitlig bedømmelse på 4.2 stjerner ud af 20.5 anmeldelser. Har du et spørgsmål om Valcom V-9975, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

VSP-V-9975

Issue 4

1947006

V-9975

SEVEN BAND EQUALIZER

INTRODUCTION

These instructions contain the specifications and

information necessary to install, operate, and

maintain the V-9975, Seven Band Equalizer.

SPECIFICATIONS

Features

• 7 active filters

• Modified 1 octave equalization

• + 12 dB boost or cut

• Constant Q equalization

• Power "ON" indicator

• Bypass switch to remove EQ from circuit

(slide type)

• High impedance output

• Line output

Nominal Specifications

• Type of Inputs:

Hi impedance 10K Ohms (unbalanced)

Stereo HiZ 10K Ohms (unbalanced)

• Type of Outputs: Line (balanced)

Hi impedance 10K Ohms (unbalanced)

• Frequency Response: 35Hz-20kHz +1dB

• Distortion: < 0.3%

• Frequency Centers: Band 1 = 60 Hz

2 = 200 Hz

3 = 560 Hz

4 = 1100 Hz

5 = 2200 Hz

6 = 4500 Hz

7 =10000Hz

Power Requirements

• -24VDC

• 150 mA

Dimensions/Weight

• 5.7" H x 8.1" W x 2.5" D

(14.5cm W x 20.6cm H x 6.4cm D)

• 2.8 lbs. (1.27 kg)

Environment

• Temperature: 0 to 50 Degrees C

• Humidity: 0-85% non-precipitating

OPERATION

The V-9975 is used to boost or attenuate specific

frequencies to improve voice intelligibility or

attenuate frequencies to help reduce feedback. The

unit can also be used to modify the frequency

response of speakers.

A "POWER" indicating LED, 7 slide controls (1 for

each of the bands), and an "EQ" bypass switch are

located on the front of the unit. The frequencies

boost/cut (1 to 12 dB), are modified with each filter's

slide control. The manual "EQ" bypass switch allows

comparison of before equalization, and after effect, in

the area being equalized. All frequency adjustments

are bypassed when the "EQ IN/OUT" switch is in the

"OUT" position.

INSTALLATION

Connections are accomplished utilizing (3) phono

jacks (2 input, 1 output) and/or (9) screw terminals.

Only qualified service personnel should install the

V-9975. See Figures 1 and 2 for actual connections.

After all connections are made and slide controls

adjusted to the desired positions, close security cover

and tighten locking screws. All connections should

be made and double checked before DC power is

supplied to the unit.

Produkt Specifikationer

Mærke:	Valcom
Kategori:	Ikke kategoriseret
Model:	V-9975

Har du brug for hjælp?

Hvis du har brug for hjælp til Valcom V-9975 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Valcom Manualer

Valcom V-2003A Manual

11 December 2025

Valcom V-9972 Manual

4 December 2025

Valcom VL520BK-F-IC Manual

1 December 2025

Valcom VL550M-F-IC Manual

30 November 2025

Valcom VIP-172AL-VRSS-IC Manual

28 November 2025

Valcom VL522M-F-FC Manual

28 November 2025

Valcom VM-SRLY Manual

27 November 2025

Valcom VIP-172AL-VRSS-SA Manual

27 November 2025

Valcom PagePro IP VIP-204 Manual

27 November 2025

Valcom VIP-176A Manual

27 November 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

IFM LMC840 Manual

20 December 2025

IFM SMF150 Manual

20 December 2025

Ecler VEO-XCTRL4D Manual

20 December 2025

Brondell SMB-25 Manual

20 December 2025

Delta H71PB Manual

20 December 2025

Kichler 4D12V27 Manual

20 December 2025

JILONG KL-33F Manual

20 December 2025

Govee H7075 Manual

20 December 2025

Signature Hardware Greyfield 481138 Manual

20 December 2025

Aqprox appTPV00 Manual

20 December 2025