Vantage Point BKSPE Manual

Vantage Point Ikke kategoriseret BKSPE

Læs gratis den danske manual til Vantage Point BKSPE (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 26 personer og har en gennemsnitlig bedømmelse på 3.8 stjerner ud af 13.5 anmeldelser. Har du et spørgsmål om Vantage Point BKSPE, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

rev 08/24/05

CAUTION: RECOMMENDED HARDWARE PROVIDED IS DESIGNED FOR SPEAKER WEIGHTS INDICATED. INSTALLER

MUST CONSIDER THE INTEGRITY AND DESIGN OF THE SPEAKER CABINET. SOME INSTALLATIONS MAY REQUIRE

THE INSTALLATION OF A THROUGH BOLT AND REINFORCEMENT BACKING IF SPEAKER CABINET DESIGN WILL NOT

SUPPORT SPEAKER WEIGHT.

ATTACHING SPEAKER ASSEMBLY TO EXTENSION

Install The plastic speaker plate cover (G) onto speaker plate link assembly installed on speaker

cabinet. Carefully align the link assemblies together using the threaded binder nut (I) as a guide.

Using the 5/16”-18 button head link screw (H), join the link assemblies together. Set your approxi-

mate tilt angle, being sure serrations are fully aligned at joint. Tighten the 5/16”-18 button head link

screw using the supplied 3/16” allen wrench.

ADJUSTING SPEAKER ALIGNMENT - ROTATION

You must first pull back the plastic speaker plate cover (G) to expose the link cap screws (J). You

can adjust the rotation of the speaker by loosening the 1/4”-20 socket head cap screws (J) on the

link assembly. Loosen these screws slightly using the 3/16” allen wrench (O). Adjust speaker to

desired position and re-tighten the link cap screws (J).

ROTATION

ADJUSTING SPEAKER ALIGNMENT - TILT

You can adjust the tilt of the speaker by loosening the 5/16”-18 button head link screw

(H) on the link assembly. Loosen the screw slightly using the 3/16” allen wrench (O).

CAUTION: Make sure you support the weight of the speaker as you loosen screw.

Adjust speaker to desired position and re-tighten the button head link screw (H).

TILT

Installation Instructions Bookshelf Series

Extended Speaker Mount-Model BKPSPE

Finished Product

PARTS LIST

Maximum weight load 25 lbs.

REQUIRED TOOLS

Assembled at Factory

A Wall Plate / Ceiling / Speaker Plate 4

B Coupler Link 4

C Extension Tube 2

D Plastic Wall Plate Cover 2

E Link 4

F Link Cap 4

G Plastic Speaker Plate Cover 2

H 5/16”-18 x 3/4” button head link screw 2

I 5/16”-18 serrated binder nut (with id. mark) 2

J 1/4”-20 x 1” socket head cap screw 16

Bagged Hardware Kit

K #14 x 2” self tapping screw 4

L #14 x 1” self tapping screw 4

M 1/4”-20 x 3/4” machine screw 4

N Toggler® Alligator anchors 4 “TOGGLER is a registered trade-

mark of Merchandise Plastics

Corp.” ALLIGATOR® ANCHOR

“Patented under US Patent num -

bers 4,181,061;4,752,170 and

5,161,296 and foreign counter

parts thereof. Other patents

pending”

SoundGear™

WARRANTY INFORMATION

All Vantage Point Products Corp. products are manufactured to ensure superior quality, performance and durability for a lifetime of

use . Warranty covers the product to be free of defects in materials and workmanship under normal and reasonable use. Vantage

Point Products will repair or replace, at our option, any product which proves to be defective upon our inspection. This warranty will

not apply to products that have been lost or damaged by misuse, abuse or accident, altered or repaired in any way or by any person

or ﬁrm other than speciﬁed by us, used in violation of instructions or incorrect assembly nor used in a manner other than speciﬁed

by us. This warranty is nontransferable to a new owner and may require proof of purchase. All claims must be directly handled with

Vantage Point Products Corp. by calling us at 1-800-582-9595.

Vantage Point Products Corp • P.O. Box 2485 Santa Fe Springs, CA 90670 USA

USA Tel: 1.800.582.9595 • Canada Tel: 905.607.9994 • Europe Tel: 31.72.581.6056

Web Site: www.vanptc.com • Email: cons-serv@vanptc.com

SOLID WOOD OR WOOD STUD - Using a stud finder locate the wood stud or framing member. Using

a pick or small drill bit locate the center of the wood stud, be careful doing this as you don’t want to go any

wider than the width of the Speaker Wall Plate (A) (wall plate will cover any extra holes) Using the wall plate

as a template mark hole position on mounting surface (see fig. 1) NOTE: In wall mounting applications

position mounting holes in a vertical pattern. Drill holes through the drywall and into the wood stud using

a 1/8” drill bit. These holes should be drilled no less than 1-7/8” deep (see fig 2) You can accomplish this

by placing a piece of tape at 1-7/8” from the end of the drill bit providing you with a guide. After holes are

drilled, mount the wall plate using the #14 x 2” self tapping screws (L).

HOLLOW DRYWALL SURFACE - Locate best mounting location in ceiling or wall. Using

the Speaker Wall Plate (A) as a template mark hole position on mounting surface (see

fig. 1) NOTE: In wall mounting applications position mounting holes in a vertical pattern. (see

fig.) Drill holes in the drywall using a 5/16” drill bit. Once holes are drilled insert the #14

TOGGLER® ALLIGATOR anchors (N) into the holes making sure anchor is flush with wall

or ceiling surface (see fig. 2) With TOGGLER® ALLIGATOR anchors in place, mount the

wall plates using the #14 x 2” self tapping screws (K) (see fig. 3).

SOLID CONCRETE OR HOLLOW BLOCK - Using the speaker wall plate (A) as a tem-

plate mark hole position on mounting surface (see fig. 1) NOTE: In wall mounting appli-

cations position mounting holes in a vertical pattern. (see fig. 3) Drill holes in the solid

concrete or hollow block using a 5/16” masonry drill bit. Once holes are drilled insert the

#14 TOGGLER® ALLIGATOR anchors (N) into the holes making sure anchor is flush

with wall or ceiling surface (see fig. 2) With TOGGLER® ALLIGATOR anchors in place,

mount the wall plate using the #14 x 2” self tapping screws (K) (see fig. 3)

16 inches

(TYPICA L)

Install mounting plate

using (2) #14 x 2”

screws into wood stud

Insert Toggler Alligator

anchor into concrete

wall or ceiling.

Insert #14 x 2” screw

through wall plate into

Alligator™ anchor.

Hammer insert into into

media until flush with

surface.

drill (2)

1/8”

dia.

1-7/8”

deep

holes

locate wood stud in

ceiling or wall

drill (2)

5/16” dia.

x 1-7/8”

deep

holes

Insert Toggler Alligator

anchor into wall.

Insert #14 x 2” screw

through wall plate

into anchor.

SPEAKER WIRE ROUTING The design of this product allows for the concealing of the speaker

wire through the center of the extension tube.

Route the speaker wire through the access hole in the coupler link (B) feed the wire through the

center of the extension tube (C) until it exits out the opposite end. Slip wire through the center

hole on the Wall plate cover (D) and into the other link set. Speaker wire should exit through gap

between the link (E) and link cap (F). See drawing to the left for reference. Make sure when tight-

ening the link assemblies the speaker wire is not pinched or crushed.

ATTACHMENT OF COUPLER LINK AND EXTENSION

Engage one half of the coupler link (B) to the extension tube (C), position assembly onto the wall/

ceiling plate (A). Move the remaining coupler link half (B) into place. Assemble using (4) 1/4”-20 x

1” socket head cap screws (J). Tighten screws using the provided 3/16” allen wrench. Make sure

coupler link (B) is fully seated onto both the wall / ceiling plate (A) and extension tube (C). This is

a good time to feed the speaker wire through assembly. Install the plastic wall / ceiling plate cover (D)

over extension tube assembly.

ASSEMBLY OF LINK TO EXTENSION TUBE

Install either of the links (E) onto the end of the extension tube (C). Secure link cap (F) to the link

(E) by using the 1/4”-20 x 1” link cap screws (J). Tighten the screws using the provided 3/16” allen

wrench. Make sure the link assembly is fully seated on extension tube (C).

INSTALLING SPEAKER PLATE 1/4”-20 THREADED HOLES

Hardware has been provided for speaker cabinets with factory installed 1/4”-20 threaded inserts.

Verify the thread size in your speaker cabinets prior to installation. Using the 1/4”-20 x 3/4” phillips

machine screws (M) install the speaker plate (A) to the speaker cabinet. Once speaker plate (A) is

installed, install the link (E) and link cap (F) assembly onto the speaker plate (A). Secure using the

1/4”-20 x 1” socket head cap screws. Tighten using the provided 3/16” allen wrench (O).

THREADED HOLES

INSTALLING SPEAKER PLATE WOOD CABINETS

Locate the optimum mounting position for the speaker plate (A). Using the the speaker plate (A)

as a template, mark mounting hole location. CAUTION: Do not drill into speaker where you could

possibly damage any internal components. Drill holes using a 1/8” drill bit. Holes should be drilled

no more than 3/4” in depth. (You can accomplish this by placing a piece of tape 3/4” from the end

of the drill bit, this will provide you with a guide) Using the #14 x 1” self tapping screws (L) mount

the speaker plate (A) to the speaker cabinet. Once speaker plate (A) is installed, install the link (E)

and link cap (F) assembly onto the speaker plate (A). Secure using the 1/4”-20 x 1” socket head

cap screws. Tighten using the provided 3/16” allen wrench (O).

NO HOLES

Produkt Specifikationer

Mærke:	Vantage Point
Kategori:	Ikke kategoriseret
Model:	BKSPE

Har du brug for hjælp?

Hvis du har brug for hjælp til Vantage Point BKSPE stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Vantage Point Manualer

Vantage Point SATS05 Manual

21 August 2024

Vantage Point UL01S Manual

21 August 2024

Vantage Point U70 Manual

20 August 2024

Vantage Point PTC20 Manual

20 August 2024

Vantage Point U50 Manual

19 August 2024

Vantage Point U42 Manual

19 August 2024

Vantage Point BKSPE Manual

19 August 2024

Vantage Point BKSP Manual

18 August 2024

Vantage Point WL01S Manual

18 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Metronic 451043 Manual

13 August 2025

Amaran Light Dome 60 Manual

13 August 2025

Sauermann CO 110 Manual

13 August 2025

Moulinex Virtuo IM1739 Manual

13 August 2025

Tefal Express Compact GV7315 Manual

13 August 2025

Cata X-MART 12 TIMER Manual

13 August 2025

Sauermann pH Safe 2 Manual

13 August 2025

Panduit WGCB24 Manual

13 August 2025

LD Systems U305 IEM Manual

13 August 2025

Watson VM-160-SE Manual

13 August 2025