Vantage Point SATS05 Manual

Vantage Point Ikke kategoriseret SATS05

Læs gratis den danske manual til Vantage Point SATS05 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 18 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 9.5 anmeldelser. Har du et spørgsmål om Vantage Point SATS05, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

SoundGear

IMPORTANT CONSIDERATIONS PRIOR TO INSTALLATION

Preview all steps before beginning. Should any portion of these instructions be unclear, contact us at 800-582-9595 for assistance.

Do Not Attempt to install this Speaker Mount if you have any doubts as to its proper installation. This Speaker Mount is specifically

designed for mounting small Surround style speakers weighing 8 lbs. or less. Use of this Speaker Mount for any other purpose

unless specified by the Manufacturer is not recommended.

B - 1/4-20 x 7/8” machine screw (5)

E - 1/4-20 x 1-1/2” machine screw (5)

F - 1/4-20 x 1-1/2”

slotted screw (5)

C - #8 x 3/4” self tapping screw (5)

G - #12 x 1-3/4” self

tapping screw (10)

H - #12-14 TOGGLER

ALLIGATOR plastic anchor (2)

I - 5/32” short allen

wrench included

Mount to WallMount to Ceiling

Invert for Shelf

Mounting

Wall / Ceiling

Plate (5)

Link Set (5) assembled at factory

Speaker Post (5)

Maximum Weight Load 8 lbs.

D - 8-32 x 5/8” machine screw (5)

A - 8-32 round key hole nut (5)

REQUIRED TOOLS

™

WARRANTY INFORMATION

All Vantage Point Products Corp. products are manufactured to ensure superior quality, performance and durability for a lifetime of use . Warranty covers

the product to be free of defects in materials and workmanship under normal and reasonable use. Vantage Point Products will repair or replace, at our

option, any product which proves to be defective upon our inspection. This warranty will not apply to products that have been lost or damaged by misuse,

abuse or accident, altered or repaired in any way or by any person or ﬁrm other than speciﬁed by us, used in violation of instructions or incorrect assembly

nor used in a manner other than speciﬁed by us. This warranty is nontransferable to a new owner and may require proof of purchase. All claims must be

directly handled with Vantage Point Products Corp. by calling us at 1-800-582-9595.

Vantage Point Products Corp • P.O. Box 2485 Santa Fe Springs, CA 90670 USA

USA Tel: 1.800.582.9595 • Canada Tel: 905.607.9994 • Europe Tel: 31.72.581.6056

Web Site: www.vanptc.com • Email: cons-serv@vanptc.com

Satellite Speaker Mount Installation

Instructions For Model SATS05

Install Link Set portion of speaker mount to wall/ceiling plate. Secure the allen set

screw enough to hold assembly in place with the weight of the speaker attached.

Install speaker with speaker post attached. Secure the allen set screw enough to

hold assembly in place with the weight of the speaker attached. Adjust to desired

angle and secure.

Link Set Mounting

All Applications

tighten allen screw

using allen key

provided

(I)

Speaker Mounting

(I)

STEP 3. Installation of Link Set

(I)

TYPE 1. POST MOUNT Key Hole Design and JBL ® models.

If your speaker has a factory key hole design you will use the 8-32 x 5/8” machine screws

in combination with the 8-32 round key hole nut. Loosely pre-assemble the speaker mount

post with 8-32 screw and key hole nut (see fig.) NOTE: be sure key hole nut is installed

with knurled edge toward post. Engage the key hole nut into key hole slot as pictured. Put

tension on the assembly by gently pulling back on speaker mount post while tightening the

8-32 screw. The key hole nut will engage on housing in key hole slot.

Proceed to step (2)

If the speaker has a screwed on metal keyhole plate you may remove it and install post as shown

in TYPE 4.

(D)

(A)

keyhole speaker post

TYPE 1

TYPE 2. POST MOUNT JBL models

JBL® Speakers are supplied with a rubber bushing that is inserted into the base of the speaker as

shown. First install the Hard Rubber Bushing supplied by JBL® into the base of the JBL Speaker.

Using the 1/4”-20 x 1-1/2” slotted flat head screw, install the screw through the speaker post and

thread or push it into the hard rubber bushing.

(F)

speaker post

bushing supplied with

JBL ® speakers

speaker TYPE 2

TYPE 3. POST MOUNT Factory Installed Threaded Insert.

If your speaker has a single factory installed 8-32 threaded insert you will use the 8-32 x

5/8” machine screw for mounting the post to the speaker housing. For speakers with single

factory installed 1/4”- 20 threaded insert you will use the 1/4”- 20 x 7/8” machine screw for

mounting the post to the speaker housing. (see fig.) Once proper configuration is deter-

mined, -secure post to speaker.

(D)

(E)

speaker post

TYPE 3

STEP 1. Installation of Speaker Post to Speaker.

Supplied are parts and hardware for mounting to various manufactures speakers. You will need to select the type that best suites your applica-

tion. If the hardware provided does not fit your speaker you will need to acquire the appropriate hardware.

TYPE 4. POST MOUNT No Factory Holes, Wood Cabinet.

(Recomended use with speakers weighing 4 lbs or

less) Locate the optimum Mounting position for the post and mark through the

center of the post for drilling. NOTE: you do not want to drill or screw into the

speaker where you could possibly damage internal components. Drill a single

hole using a 3/32” drill bit. This hole should be drilled no more than 1/2” deep.

You can accomplish this by placing a piece of tape a 1/2” from the end of the drill

bit providing you with a guide. After hole is drilled, mount the post using the #8 x

3/4” self tapping screw.

Proceed to step (2)

drill 3/32” dia. x 1/2” deep hole

(C)

TYPE 4

speaker post

HOLLOW DRYWALL SURFACE - Locate best mounting location in ceiling or

wall. Using the wall plate as a template mark hole position on mounting surface (see

fig. 1)

NOTE: In wall mounting applications position mounting holes in a vertical pattern. (see

fig.) Drill holes in the drywall using a 5/16” drill bit. Once holes are drilled insert

the #12 plastic anchors into the holes making sure anchor is flush with wall or ceiling

surface (see fig. 2) With plastic anchors in place, mount the wall plates using the #12

x 1-3/4” self tapping screws (see fig. 3) Complete the installation of the remaining

wall / ceiling plates.

Proceed to step (3)

SOLID WOOD OR WOOD STUD - Using a stud finder locate the wood stud or

framing member. Using a pick or small drill bit locate the center of the wood stud, be

careful doing this as you don’t want to go any wider than the width of the wall plate

(wall plate will cover any extra holes) Using the wall plate as a template mark hole

position on mounting surface (see fig. 1) NOTE: In wall mounting applications position

mounting holes in a vertical pattern. Drill holes through the drywall and into the wood

stud using a 1/8” drill bit. These holes should be drilled no less than 1-7/8” deep (see

fig 2) You can accomplish this by placing a piece of tape a 1-7/8” from the end of the

drill bit providing you with a guide. After holes are drilled, mount the wall plate using

the #12 x 1-3/4” self tapping screws. Complete the installation of the remaining wall

/ ceiling plates. Proceed to step (3)

Mounting Hardware is supplied for 3 different surface applications. You will need to determine what style hardware will work

best with your mounting surface. NOTE: Always use CAUTION when drilling into a wall or ceiling. Make sure you are avoiding all

electrical and water lines.

drill (2)

1/8” dia.

x 1-7/8”

deep

holes

locate

wood stud

in ceiling

or wall

install mounting plate

using (2) #12 x 1-3/4”

screws into wood stud

(G)

drill (2)

1/8” dia. x

1-7/8” deep

holes

Insert plastic

anchor into wall.

Inse rt #1 2 x 1-3 /4”

scre w thr ough wall

plat e int o anc hor.

(G)

(H)

Figure 1

Figure 2

Insert plastic

anchor into concrete

wall or ceiling.

Insert #12 x 1-3/4”

screw through wall plate

into the plastic anchor.

hammer insert into

media until flush with

surface.

(G)

(H)

Figure 3

STEP 2. Installation of Wall / Ceiling Plate

SOLID CONCRETE OR HOLLOW BLOCK Using the wall plate as a template

mark hole position on mounting surface (see fig. 1)

NOTE: In wall mounting applications position mounting holes in a vertical pattern. (see

fig.) Drill holes in the solid concrete or hollow block using a 5/16” masonry drill bit.

Once holes are drilled insert the #12 plastic anchors into the holes making sure

anchor is flush with wall or ceiling surface (see fig. 2) With plastic anchors in place,

mount the wall plate using the #12 x 1-3/4” self tapping screws (see fig. 3) Complete

the installation of the remaining wall / ceiling plates.

Proceed to step (3)

Produkt Specifikationer

Mærke:	Vantage Point
Kategori:	Ikke kategoriseret
Model:	SATS05

Har du brug for hjælp?

Hvis du har brug for hjælp til Vantage Point SATS05 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Vantage Point Manualer

Vantage Point SATS05 Manual

21 August 2024

Vantage Point UL01S Manual

21 August 2024

Vantage Point U70 Manual

20 August 2024

Vantage Point PTC20 Manual

20 August 2024

Vantage Point U50 Manual

19 August 2024

Vantage Point U42 Manual

19 August 2024

Vantage Point BKSPE Manual

19 August 2024

Vantage Point BKSP Manual

18 August 2024

Vantage Point WL01S Manual

18 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

AmpliVox Airvox SW695 Manual

15 Juni 2025

Stiga SBC 635 KD Manual

15 Juni 2025

Cleveland 36CGM300 Manual

15 Juni 2025

Gourmia GTF7970 Manual

15 Juni 2025

Planet Audio P9630B Manual

15 Juni 2025

ORNO OR-DOM-YR-934UD Manual

15 Juni 2025

Lavex 842CD12VST12 Manual

15 Juni 2025

Marshall RCP-PLUS Manual

15 Juni 2025

Hughes & Kettner BassForce XL Manual

15 Juni 2025

Hughes & Kettner Red Box Mk III Manual

15 Juni 2025