Varad IL2W Manual

Varad Ikke kategoriseret IL2W

Læs gratis den danske manual til Varad IL2W (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 24 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 12.5 anmeldelser. Har du et spørgsmål om Varad IL2W, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

IL2W

IM-IL2Wv1

Thank you for purchasing the Varad IL2W, dual 1 watt LED

lighting system with driver. To ensure proper use please

carefully read this installation manual prior to installation.

Installation Guide

www.varad.com

1. IL2WC - Digital Controller

2. Two 1 watt LEDs

3. Mounting bracket

4. Power Harness

5. Self tapping screws, 4pcs.

6. flush mount screws, 2pcs.

7. Tie straps, 4 pcs.

Power Harness LEDs

Digital Controller Description

Technical Specifications

Physical Specifications:

Digital controller:

Height - 0.75”

Width - 1.5”

Length - 2.25”

Current Draw - 250ma

LED:

Length: 3”, Width: 1.25”, Height: 0.55”

Wires:

12’ of cable

Electrical Specifications:

Digital controller:

12v - 24v input

LEDs:

Orange - ALINGAP, 350ma, 180 degree

Red - TS ALINGAP, 350ma, 180 degree

Blue/Green/White - INGAN 350ma, 180 degree

Parts List

Function

These 1 watt LEDs are designed to create accent

lighting for automotive interiors. Applications include,

speaker boxes, footwells, amplifier racks, doors and

much more...

Precautions

To prevent fire or shock hazard, do not expose the

digital controller to rain or moisture.

To avoid electrical shock, do not open the digital

controller. Refer servicing to a factory authorized

dealer. Do not attempt to disassemble the LED or

damage will occur.

Do not bend the wire away from the

bottom of the LED or water may leak

into the housing.

Required tools

· Wire Stripper

· Wire cutter

· Assorted drill dits

· Cordless drill

· Screwdriver

Installation of LEDs

Visually inspect for a location to mount the LED. The

light dispersion pattern will vary depending upon the

location of the LED. It is recommended that you power

up the LED and move it around to determine the

location that provides the best lighting. When you have

found a suitable location, begin to install by marking

each drilling point and pre-drill each hole with a 1/8” drill

bit. Mount the LED with supplied tapping screws. Once

again making an effort not to bend the wire away from

the bottom of the LED, so no damage should occur.

Connect wiring

harness as indicated below:

· Red wire - Battery Positive, 12v - 24v

· Black wire - Negative (Ground)

· Grey wire - refer to installation with

SL200 / SL210 or stand alone

Installation of the Controller

Install the Digital Controller inside the vehicle. Find a

location that will allow all the wires to the LEDs to

connect without binding. The location needs to be with

in 144” of the LED.

Power Harness

When all controllers and LEDs are installed you can

proceed to plug all the conectors into the IL2W

controller.

Installation with SL200 / SL210

With the SL200 and SL210

there is an optional LED

expansion port and wire

harness. If you choose, you

can connect the grey

ground trigger wire of the

IL2W to this expansion

connector.

In doing so, this will allow your IL2W to do some of the

same intensity control, strobing, breathing and music

react modes.

Connect wiring

harness as indicated below:

· Red wire - Battery Positive, 12v - 24v

· Black wire - Negative (Ground)

· Grey wire - expansion output on the

SL200, SL210

(NOTE) if using with the expansion output of the SL200

or SL210, Please be aware that the not all strobing and

breathing patterns will function with the IL2W.

Stand alone installation

To install the IL2W in a stand alone application, the grey

ground trigger must be attached to a negative ground

point.

Connect wiring

harness as indicated below:

· Red wire - Battery Positive, 12v - 24v

· Black wire - Negative (Ground)

· Grey wire - Negative (Ground)

Varad's product warranty covers against breakage due to defects in

materials or workmanship for one year from the date of purchase.

Warranty is only valid with proof of purchase from an authorized Varad

dealer. Varad's warranty program does not cover cosmetic damage,

damage due to acts of god, accident, misuse, abuse or negligence to the

product. Repair or replacement as provided under this warranty is the

exclusive remedy of the consumer. Varad shall not be liable for any express

or implied warranty on this product. Except to the extent provided by this

warranty or prohibited by applicable law, there are no implied nor

expressed warranties or merchantability or fitness for a particular

purpose of this product.

www.varad.com

techsupport@varad.com

Designed and Engineered in the U.S.A. Assembled in China

Warranty

Trouble Shooting

System does not turn “ON”

Check to see that the grey wire is grounded or has a

good connection to SL200 or SL210 expansion output.

LED does not work

Check to see that the cable between LED and controller

is not damaged.

Plug into the other port to verify that it is the LED that

is not functioning.

Produkt Specifikationer

Mærke:	Varad
Kategori:	Ikke kategoriseret
Model:	IL2W

Har du brug for hjælp?

Hvis du har brug for hjælp til Varad IL2W stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Varad Manualer

23 August 2024

23 August 2024

23 August 2024

23 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

10 Oktober 2025

10 Oktober 2025

10 Oktober 2025

10 Oktober 2025

Oras Saga 3970 Manual

10 Oktober 2025

TOA AT-4030B-EB Manual

10 Oktober 2025

TOA VX-030DA Manual

10 Oktober 2025

TOA RS-481 Manual

10 Oktober 2025

TOA AT-4200B-EB Manual

10 Oktober 2025

Xerox DocuShare Manual

10 Oktober 2025