Vaxcel T0695 Manual

Vaxcel Ikke kategoriseret T0695

Læs gratis den danske manual til Vaxcel T0695 (10 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 4 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 2.5 anmeldelser. Har du et spørgsmål om Vaxcel T0695, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/10

Page 1 / 5

Important to Know:

1. If you are not familiar with state and local electrical

codes, it is recommended that you consult with a

qualified electrician.

2. This fixture requires a 120 VAC, 60 Hz power

source.

3. For general safety and to avoid any possible

damage to the sensor, be sure the power is

switched "off" before adjustment.

Maximum Wattage: 2-150 W (bulb not included)

Working Temperature Range: - 13°F ~ 113°F

ASSEMBLY AND INSTALLATION

INSTRUCTIONS

NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements.

2. READ AND SAVE THESE INSTRUCTIONS.

T0694 / T0695

Features:

WARNING:

TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF

POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE.

Note: Fixture can be wall mounted or eave mounted.

Wall Mounted

Eave Mounted

Read notes section on page 4 for additional information about mounting location of fixture.

Light fixture and sensor should be mounted as shown above when installed (depending upon type of installation)

Before installing the light fixture under an eave, the sensor head must be rotated as shown in the next two steps for

proper operation and to avoid the risk of electrical shock.

1. Motion sensor: turns light ON automatically when

motion is detected and turns light OFF or remains

in low-level brightness when motion stops.

2. Photocell keeps the light OFF during daylight hours.

Hardware Package (included):

Decorative cover

Fixture Mounting Screw

Mounting Strap

Wire Connector

Gasket

Mounting Screw X2

#8/32X1/2 in

Mounting Screw X2

#6/32 X1/2 in

Mounting Screw X2

#10/24 X1/4 in

For eave mounted only:

Rotate the sensor head towards the back plate.

Rotate the sensor head clockwise 180˚ so the controls face down.

Controls

Backplate

Controls

(1) Phillips-head Screwdriver

1. Phillips-head screwdriver for attaching mounting screws to

mounting strap, mounting bracket and fixture to mounting bracket.

Tools Needed:

221031

Produkt Specifikationer

Mærke:	Vaxcel
Kategori:	Ikke kategoriseret
Model:	T0695

Har du brug for hjælp?

Hvis du har brug for hjælp til Vaxcel T0695 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Vaxcel Manualer

18 December 2025

18 December 2025

18 December 2025

18 December 2025

18 December 2025

18 December 2025

18 December 2025

18 December 2025

18 December 2025

18 December 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Gamdias Aura GC5 Manual

18 December 2025

Aqprox appTPV03 Manual

18 December 2025

Nokia Solo Bud+ SB-201 Manual

18 December 2025

Wind River KG300 Manual

18 December 2025

TOTO TS2D Manual

18 December 2025

Silverstone SX800-LTI Manual

18 December 2025

Wine-Mate WM-2500SSWWC Manual

18 December 2025

Fulgor Milano FEHCPK 3605 ID Manual

18 December 2025

Brondell LumaWarm L60 Manual

18 December 2025

Bravilor Bonamat Bolero 32 CS Manual

18 December 2025