Vemer EV2M-2DIN Manual

Vemer Ikke kategoriseret EV2M-2DIN

Læs gratis den danske manual til Vemer EV2M-2DIN (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 29 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 15 anmeldelser. Har du et spørgsmål om Vemer EV2M-2DIN, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Mod. EV2M-2DIN

EV2M-4DIN

EV2M-R

V3IS00443–010

EV2M-2DIN

EV2M-4DIN

EV2M-R

EV2M-2DIN

EV2M-4DIN

EV2M-R

EV2M-2DIN

EV2M-4DIN

EV2M-R

 Power supply connection terminals

 Voltage reading window

 Current reading window

 Parameter setting key

 Metering connection terminals

36 60

72 60

72 75

COM I V

LOAD

COM I V

LOAD

5 4 3 12

LOAD

P1P2

EV2M-2DIN

TRUE RMS

Prg

Input 5(6)A 600 V~

PRG

Input 5(6)A~ 600 V~

TRUE RMS

EV2M-4DIN

EV2M-R

TRUE RMS

Input 5(6)A 600 V~

Prg

User Manual

DIGITAL VOLMETER-AMMETER

Read all the instructions carefully

The EV2M meters are digital multimeters to measure TRMS values (true

root mean square values) for alternate voltage and current. It reads these two

quantities simultaneously on two 3-digit LED displays.

SAFETY WARNINGS

During the installation and operation of the instrument, proceed in accordance

with the instructions below:

1) The instrument should be installed by a competent operator following the

installation diagrams carefully

2) Before touching the connector terminals make sure that the wires to be connected

or already connected to the instrument are not live

3) The instrument should be installed in a panel from which no access can be gained

to the terminals after installation

4) Do not power or connect the instrument if any part of it is damaged

5) The electrical system of the building in which the instrument is to be installed

should have a switch and a protective device against over-currents

6) The instrument is designed for installations with over-voltage category III and

pollution level 2, in accordance with the EN 61010-1 standard.

Code Model Description

VE149100 EV2M–2DIN Voltage-current reading meter 2 DIN

VE196200 EV2M–4DIN Voltage-current reading meter 4 DIN

VE195400 EV2M–R Voltage-current reading meter 72 x 72

TECHNICAL SPECIFICATIONS

• Power supply: 230 V AC (-15%/+10%), 50/60 Hz

– maximum consumption: 4 VA

• Measurement of true root mean square (TRMS) values for voltage and current

• Voltmeter connection:

– connection type: direct

– maximum voltage: VMAX = 600 V

– maximum consumption: 2,5 VA

• Ammeter connection:

– connection type: by AT x/5 A

– available scales: from 5/5 A to 1000/5 A

– maximum and nominal current rating: In = 5 A; IMAX = 6 A

– maximum consumption: 2,5 VA

• Reading filter (update speed)

• Maximum section of wires:

– 6 mm2 for model EV2M-2DIN and EV2M-4DIN

– 2,5 mm2 for model EV2M-R

• Operating conditions:

– operating temperature: –10 ÷ +45 °C

– relative humidity: 10% ÷ 90% non-condensing

• Storage temperature: –20 ÷ +60 °C

• Display: 7-segment LED digit display

• Enclosure:

– 2 module DIN, RAL 7035 gray for EV2M-2DIN

– 4 module DIN, RAL 7035 gray for EV2M-4DIN

– standardized dimensions 72 x 72 mm according to DIN 43700 for EV2M-R

• Protection rating: IP51 on the front

RESOLUTION AND ACCURACY

• Voltage (full scale V MAX

= 600 V):

– Maximum reading: 615 V

– Minimum reading: 10V

– Resolution: 1V

– Accuracy: ± 0,5% full scale ± 1 digit (from 3% to 100% of full scale value)

• Current (full scale In = 5 A):

– Maximum reading: 6 A

– Minimum reading: 0,02 A

– Resolution: 0,01 A

– Accuracy: ± 0,5% full scale ± 1 digit (from 3% to 100% of full scale value)

Note: current data refer to the values provided by the amperometric transformer;

maximum and minimum readings directly depend on the AT ratio used, whereas

resolution is dependent on the scale used, as described below.

OPERATION

During normal operation the device reads the Voltage value (Volts) in the top window and the

current value (Amperes) in the bottom window.

The current value is automatically read in the most appropriate scale:

• 0,01 A resolution in the 0,02 A ÷ 10 A range (e.g.: )6.47

• 0,1 A resolution in the 10 A ÷ 100 A range (e.g.: )39.1

• 1 A resolution in the 100 A ÷ 1000 A range (e.g.: )528

• 10A resolution for values above 1000 A (e.g.: : )1.03

In the latter case the value is expressed in kA with the decimal point lit after the first digit and

the LED point lit to the right of the last digit above the kA symbol

SETTINGS

After switching the device on it is possible to check and/or change some of the factory settings

by pressing or holding down the key according to the procedure described below.Prg

• Press the Prg key

The voltage and current reading displays will read a value

referring to the transformer primary (factory setting: 5).

To change this value, hold down the key for at least 2 Prg

seconds until the digits ﬂ ash. Then press and hold the key

pressed until the desired value is reached (the reading will

increase by 5-unit steps; 1000 is read as ).001.

• After a few seconds from the moment the key is released, a value

will indicate the reading ﬁ lter (factory value: 10). The lower this

value, the faster the readings will be updated, the higher the

value, the more stable the reading will be.

To change this value, hold down the key for at least 2 Prg

seconds until the digits ﬂ ash. Then press the key repeatedly

until the desired value is set (the reading will increase by 1-unit

steps; the value range is from 1 to 20).

After one of these parameters is set the device will go off and

then on again using the new parameters. The device is reset

automatically with no need to disconnect it from the power supply.

ERROR MESSAGES

• Memory error: EEE

The device has undergone damage that jeopardizes operation

• Overload error: KKK

The quantity measured (voltage and/or current) has exceeded the

maximum admissible value: V > 1,02 x VMAX; I > 1,2 x In.

Reset is automatic.

REFERENCE STANDARS

Conformity to the EU directives:

2006/95/CE (Low Voltage)

89/336/CEE mod. modified by 92/31/EEC and 93/68/EEC (EMC)

is declared with reference to the following harmonised standards:

EN 61010-1, EN 61000-6-2 and EN 61000-6-4

Dimensions

Connection

Description











Produkt Specifikationer

Mærke:	Vemer
Kategori:	Ikke kategoriseret
Model:	EV2M-2DIN

Har du brug for hjælp?

Hvis du har brug for hjælp til Vemer EV2M-2DIN stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Vemer Manualer

Vemer Mini Time Manual

20 Juni 2025

Vemer TCR Manual

2 Oktober 2024

Vemer Set PC RF8 Manual

1 Oktober 2024

Vemer ADR-D Vision Manual

22 September 2024

Vemer ES Manual

10 September 2024

Vemer Thalos RF Manual

3 September 2024

Vemer VE 502E Manual

1 September 2024

Vemer Elettrosonda Z Manual

25 August 2024

Vemer VE LAN Manual

10 August 2024

Vemer LCR048 Manual

10 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Hendi 551813 Manual

2 November 2025

BougeRV E50 Manual

2 November 2025

Beverage-Air VueMax VMHC-7-1-G Manual

2 November 2025

OneConcept Magic-Carpet DX Manual

2 November 2025

Tonor T20 Manual

2 November 2025

Beverage-Air Horizon HRP3HC-1HS Manual

2 November 2025

Workzone AB1600 Manual

2 November 2025

Homedics BH-100-AU Manual

2 November 2025

Beverage-Air Horizon HFP1HC-1S Manual

2 November 2025

Beverage-Air VueMax VMHCSL-18-1-B Manual

2 November 2025