Verbos Electronics Control Voltage Processor Manual

Verbos Electronics Ikke kategoriseret Control Voltage Processor

Læs gratis den danske manual til Verbos Electronics Control Voltage Processor (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 6 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 3.5 anmeldelser. Har du et spørgsmål om Verbos Electronics Control Voltage Processor, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Control Voltage Processor

Congratulations on obtaining your new Verbos Electronics Control Voltage

Processor. This Euro-Rack format module allows mixing, scaling, inverting,

crossfading, slewing, compressing, offsetting and modulating of not only control

voltages but any signals inside your modular synthesizer.

The Top Section

The top section of the module is a Slew Rate Processor with independent control

of the positive and negative moving voltages. In addition to the panel control for

each of these, there is a c.v. input for each with a reversing attenuator to scale

the control amount. A Trigger input and manual gate button will send the output

up to 8 volts at the Positive rate and back down at the Negative rate. The Shape

can be continuously swept from linear to curved, as expected from classic por-

tamento circuits. The curves are “true RC” in the sense that they are not created

using feedback, therefore they always start fast and end slow throughout the

voltage range from -11 volts to +11 volts. A Gate Out goes high for negative volt-

ages and low for positive ones and allows looping if it is patched to the trigger

in. Bounce, a feature unique to this module, allows control voltage to overshoot

its destination by an amount set by the control, at the rate of the Positive control.

This gives the effect of letting go of a tape machine’s reel and hearing the pitch

wobble.

The Lower Sections

The lower two sections are identical voltage processors. Inputs 1 and 2 have

reversing attenuators, allowing inverting, scaling, addition and subtraction. Inputs

3 and 4 are a voltage controlled crossfader, which can also be used as a VCA

that opens or closes with voltage or even a 4 quadrant modulator. The Offset

control will add or subtract a xed voltage to the mix. The voltage range of these

processors is more than +/-11 volts.

18HP • 240g • +12v 85mA • -12v 83mA

Produkt Specifikationer

Mærke:	Verbos Electronics
Kategori:	Ikke kategoriseret
Model:	Control Voltage Processor

Har du brug for hjælp?

Hvis du har brug for hjælp til Verbos Electronics Control Voltage Processor stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Verbos Electronics Manualer

Verbos Electronics Control Voltage Processor Manual

25 August 2024

Verbos Electronics Mini Horse Manual

23 August 2024

Verbos Electronics Polyphonic Envelope Manual

23 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Tripp Lite U339-001-FLAT Manual

31 Juli 2025

Tripp Lite IBLOK2-0 Manual

31 Juli 2025

Tripp Lite TR-6FM Manual

31 Juli 2025

L.R.Baggs Element Active System Manual

31 Juli 2025

Tripp Lite Protect It! TLP310USBCW Manual

31 Juli 2025

Tripp Lite PR25 Manual

31 Juli 2025

SolidDrive SD-1G Manual

31 Juli 2025

Tripp Lite PR7 Manual

30 Juli 2025

Wren & Cuff 70's Your Face Fuzz Manual

30 Juli 2025

Advantech WISE-2211 Manual

30 Juli 2025