Viking PROLPK1 Manual

Viking Ikke kategoriseret PROLPK1

Læs gratis den danske manual til Viking PROLPK1 (6 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 14 personer og har en gennemsnitlig bedømmelse på 3.5 stjerner ud af 7.5 anmeldelser. Har du et spørgsmål om Viking PROLPK1, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/6

PRONGK1 / PROLPK1 Conversion Kit

for 30” / 36” / 42” / 54” Outdoor Grills

Power Burner Accessory

Side Burner Accessory

Installation

GUIDE

IMPORTANT: PLEASE READ AND FOLLOW

1. Before beginning, please read these instructions completely and carefully.

2. Do not remove permanently a xed labels, warnings, or plates from

product. This may void the warranty.

3. Please observe all local and national codes and ordinances.

CAUTION: Before proceeding with the conversion, shut o the gas

supply to the appliance prior to disconnecting the electrical

power.

This conversion kit shall be installed by a

quali ed service agency in accordance with the

manufacturer’s instructions and all applicable

codes and requirements of the authority having

jurisdiction. If the information in these instructions

is not followed exactly, a  re, explosion or

production of carbon monoxide may result

causing property damage, personal injury or loss

of life. The quali ed service agency is responsible

for the proper installation of this kit. The

installation is not proper and complete until the

operation of the converted appliance is checked

as speci ed in the manufacturer’s instructions

supplied with the kit.

WARNING

GAS CONVERSION

To convert a grill or accessory burners from natural to LP/Propane gas or

LP/Propane to natural, you must use the conversion kit supplied by the

manufacturer. When converting to Natural Gas, use the PRONGK1 kit for

30”/36” / 42”/54” Grills, Power Burner and Side Burner models. When

converting to LP/Propane, use the PROLPK1 kit for 30”/36” / 42”/54” Grills,

Power Burner and Side Burner models. Conversions should only be done by

an authorized service technician.

PRONGK1 Conversion Kit Part List

(1) Elbow 1/2 NPT, 90 degree Pipe Elbow

(1) #41S Ori ce, Main Burner 36” Model

(2) #44S Ori ce, Sear Burner 36” Model

(2) #50 Ori ce, IR Rotis 30”/36”/54” Models

(2) #68 Smoker Ori ce

(3) #41L, 1.375 Ori ce, Main Burner 30”/42”/54” Models

(1) #42S Ori ce, Sear Burner 30”/42”/54” Models

(1) 4/11 Regulator

(2) #185 Side Burner Ori ce

(1) #50L Ori ce, Inner Power Burner

(1) #35L Ori ce, Outer Power Burner

(1) Valve Valve, Main Burner, Red Spring

(1) 068907-000 Conversion Kit Instructions

(1) PF030427 Conversion Label

(1) 071523-000 Red Natural Gas Label

(1) #48 Ori ce, #48

PROLPK1 Conversion Kit Part List

(1) Elbow 3/8” Flare to 1/2” FIP Pipe Elbow

(4) #53 Ori ce, Main Burner 36” Model

(1) #55 Ori ce, Sear Burner 36” Model

(2) #57 Ori ce, IR Rotis 30”/36”/54” Models

(2) #77 Ori ce, Smoker

(3) #53L, 1.375 Ori ce, Main Burner 30”/42”/54” Models

(2) #54 Ori ce, Sear Burner 30”/42”/54” Models

(1) 2-stage Regulator w/Hose

(2) #115 Side Burner Ori ce

(1) #57L Ori ce, Inner Power Burner

(1) #50L Ori ce, Outer Power Burner

(1) Valve Valve, Main Burner, Red Spring

(1) 068907-000 Conversion Kit Instructions

(1) PF030427 Conversion Label

(1) 071522-000 Yellow LP Gas Label

(1) #56S Ori ce, #56S

• 1 ¼” open end wrench or large channel locks (removing / installing

NG regulator)

• Phillips screwdriver (removing installing rear panel / adjusting air

shutters)

• ½” deep socket and ratchet (removing / installing gas ori ces on

burner valves)

• ½” open end wrench (removing / installing rotisserie burner

ori ce)

• 7/16” open end wrench or socket (removing / installing manifold

pipe)

• 3/8” socket (to remove the heat shield)

• 3/32” blade slot screwdriver - 3” long shaft (adjusting burner valves

to obtain proper minimum  ame)

• 5/8” open end wrench (removing / installing LP regulator & hose

to  are  tting)

• Pipe wrench (removing / installing the LP – brass 90 degree ½” x

3/8”  are elbow and NG – 90 degree street elbow connection at

manifold)

• Pipe dope, yellow Te on gas tape, etc (sealing gas connections)

Tools Needed

*NOTE: All parts in the kit may not be used depending on model being converted

Produkt Specifikationer

Mærke:	Viking
Kategori:	Ikke kategoriseret
Model:	PROLPK1

Har du brug for hjælp?

Hvis du har brug for hjælp til Viking PROLPK1 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Viking Manualer

Viking VE-9X12Y-1P Manual

6 Juni 2025

Viking VE-9X12Y-2P Manual

6 Juni 2025

Viking VE-9X12Y-3P Manual

6 Juni 2025

Viking PROLPK1 Manual

31 Januar 2025

Viking PRONGK1 Manual

31 Januar 2025

Viking RD24CSTSS Manual

5 September 2024

Viking VBO1830S Manual

6 August 2024

Viking PDDP242 Manual

3 August 2024

Viking RD30BG6SS Manual

2 August 2024

Viking VSP30 Manual

1 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Falmec Brera 75 Manual

4 Oktober 2025

Kenwood Mesmerine TFM810 Manual

4 Oktober 2025

AFK EWK-2200.7C Manual

4 Oktober 2025

Realme Narzo 60x Manual

4 Oktober 2025

AFK RC-22.16 Manual

4 Oktober 2025

Black Box HG-2 Manual

4 Oktober 2025

Sony SNCA-AN1 Manual

4 Oktober 2025

AFK PME-2000.15.1 Manual

4 Oktober 2025

Orangemonkie Foldio1 Manual

4 Oktober 2025

Kenwood Elegancy ZJP11 Manual

4 Oktober 2025