Viking PRONGK1 Manual

Viking Ikke kategoriseret PRONGK1

Læs gratis den danske manual til Viking PRONGK1 (6 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 11 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 6 anmeldelser. Har du et spørgsmål om Viking PRONGK1, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/6

PRONGK1 / PROLPK1 Conversion Kit

for 30” / 36” / 42” / 54” Outdoor Grills

Power Burner Accessory

Side Burner Accessory

Installation

GUIDE

IMPORTANT: PLEASE READ AND FOLLOW

1. Before beginning, please read these instructions completely and carefully.

2. Do not remove permanently a xed labels, warnings, or plates from

product. This may void the warranty.

3. Please observe all local and national codes and ordinances.

CAUTION: Before proceeding with the conversion, shut o the gas

supply to the appliance prior to disconnecting the electrical

power.

This conversion kit shall be installed by a

quali ed service agency in accordance with the

manufacturer’s instructions and all applicable

codes and requirements of the authority having

jurisdiction. If the information in these instructions

is not followed exactly, a  re, explosion or

production of carbon monoxide may result

causing property damage, personal injury or loss

of life. The quali ed service agency is responsible

for the proper installation of this kit. The

installation is not proper and complete until the

operation of the converted appliance is checked

as speci ed in the manufacturer’s instructions

supplied with the kit.

WARNING

GAS CONVERSION

To convert a grill or accessory burners from natural to LP/Propane gas or

LP/Propane to natural, you must use the conversion kit supplied by the

manufacturer. When converting to Natural Gas, use the PRONGK1 kit for

30”/36” / 42”/54” Grills, Power Burner and Side Burner models. When

converting to LP/Propane, use the PROLPK1 kit for 30”/36” / 42”/54” Grills,

Power Burner and Side Burner models. Conversions should only be done by

an authorized service technician.

PRONGK1 Conversion Kit Part List

(1) Elbow 1/2 NPT, 90 degree Pipe Elbow

(1) #41S Ori ce, Main Burner 36” Model

(2) #44S Ori ce, Sear Burner 36” Model

(2) #50 Ori ce, IR Rotis 30”/36”/54” Models

(2) #68 Smoker Ori ce

(3) #41L, 1.375 Ori ce, Main Burner 30”/42”/54” Models

(1) #42S Ori ce, Sear Burner 30”/42”/54” Models

(1) 4/11 Regulator

(2) #185 Side Burner Ori ce

(1) #50L Ori ce, Inner Power Burner

(1) #35L Ori ce, Outer Power Burner

(1) Valve Valve, Main Burner, Red Spring

(1) 068907-000 Conversion Kit Instructions

(1) PF030427 Conversion Label

(1) 071523-000 Red Natural Gas Label

(1) #48 Ori ce, #48

PROLPK1 Conversion Kit Part List

(1) Elbow 3/8” Flare to 1/2” FIP Pipe Elbow

(4) #53 Ori ce, Main Burner 36” Model

(1) #55 Ori ce, Sear Burner 36” Model

(2) #57 Ori ce, IR Rotis 30”/36”/54” Models

(2) #77 Ori ce, Smoker

(3) #53L, 1.375 Ori ce, Main Burner 30”/42”/54” Models

(2) #54 Ori ce, Sear Burner 30”/42”/54” Models

(1) 2-stage Regulator w/Hose

(2) #115 Side Burner Ori ce

(1) #57L Ori ce, Inner Power Burner

(1) #50L Ori ce, Outer Power Burner

(1) Valve Valve, Main Burner, Red Spring

(1) 068907-000 Conversion Kit Instructions

(1) PF030427 Conversion Label

(1) 071522-000 Yellow LP Gas Label

(1) #56S Ori ce, #56S

• 1 ¼” open end wrench or large channel locks (removing / installing

NG regulator)

• Phillips screwdriver (removing installing rear panel / adjusting air

shutters)

• ½” deep socket and ratchet (removing / installing gas ori ces on

burner valves)

• ½” open end wrench (removing / installing rotisserie burner

ori ce)

• 7/16” open end wrench or socket (removing / installing manifold

pipe)

• 3/8” socket (to remove the heat shield)

• 3/32” blade slot screwdriver - 3” long shaft (adjusting burner valves

to obtain proper minimum  ame)

• 5/8” open end wrench (removing / installing LP regulator & hose

to  are  tting)

• Pipe wrench (removing / installing the LP – brass 90 degree ½” x

3/8”  are elbow and NG – 90 degree street elbow connection at

manifold)

• Pipe dope, yellow Te on gas tape, etc (sealing gas connections)

Tools Needed

*NOTE: All parts in the kit may not be used depending on model being converted

Produkt Specifikationer

Mærke:	Viking
Kategori:	Ikke kategoriseret
Model:	PRONGK1

Har du brug for hjælp?

Hvis du har brug for hjælp til Viking PRONGK1 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Viking Manualer

Viking VE-9X12Y-1P Manual

6 Juni 2025

Viking VE-9X12Y-2P Manual

6 Juni 2025

Viking VE-9X12Y-3P Manual

6 Juni 2025

Viking PROLPK1 Manual

31 Januar 2025

Viking PRONGK1 Manual

31 Januar 2025

Viking RD24CSTSS Manual

5 September 2024

Viking VBO1830S Manual

6 August 2024

Viking PDDP242 Manual

3 August 2024

Viking RD30BG6SS Manual

2 August 2024

Viking VSP30 Manual

1 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Supermicro SuperStorage 6039P-E1CR16L Manual

3 Oktober 2025

Sony MRW-G3 Manual

3 Oktober 2025

GYS DIAG-BATIUM 100.12 FV Manual

3 Oktober 2025

Sony INZONE KBD-H75 Manual

3 Oktober 2025

3 Oktober 2025

3 Oktober 2025

3 Oktober 2025

2 Oktober 2025

Supermicro SuperStorage 6029P-E1CR12L Manual

2 Oktober 2025

Sony BKM-FW12 Manual

2 Oktober 2025