VintageView GNR-LABEL2 Manual

VintageView Ikke kategoriseret GNR-LABEL2

Læs gratis den danske manual til VintageView GNR-LABEL2 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 14 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 7.5 anmeldelser. Har du et spørgsmål om VintageView GNR-LABEL2, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Grain + Rod

Wall Mounted Wood and Metal Wine Rack Panel Installation Instructions

The following instructions can be used for all congurations of the Grain + Rod modular wine wall

system.

Video guides, spec sheets, and additional support are available at grainandrod.com.

• (1) Wood board

• (3, 6, or 9) Vino Pins

or Vino Rail

• Extension studs

(optional)

• (6 or 18) 35mm

screws

Parts List & Congurations

• (3) Keyhole hangers

• (6) Keyhole screws

• (3) Sprial Drywal Anchors

• (3) Wood lags

• (1) Plotting Guide

Step 1: Attach the Keyholes

Using 2 short wood screws for each hanger, afx 3 metal

keyholes to the corresponding pre-drilled holes on the

back of the wood board. Position the hanger with the

smaller side of the opening toward the top of the board.

Step 2: Install the Racks

Insert the 35mm screw sthrough the back of the board so

the screw head ts into the inset hole. For Vino Pins* lay-

outs, ensure the base Pin (wider impression) is installed

on the lower of the two holes, and the neck Pin (narrower

impression) is installed in the higher of the two holes.

Thread the Pin or Rail to the front of the board onto the

exposed screw that is sticking through. With a screw-

driver or drill, tighten the Pin or Rail.

Repeat for remaining Pins or Rails.

* If installing a two-deep or three-deep Vino Pins cong-

uration, connect the extension Pins before attaching to

the board. Thread a stud into one end of the extension

Pin and screw the starter base Pin onto the remaining

exposed end and rmly hand tighten. Connect any ad-

ditional extensions in a similar fashion for both the neck

and base side of the Pins.

Instructions

Step 3: Plot the Wall

Use the printed template to mark the mounting holes on

the wall. If installing multiple boards, we recommend

1/8” spacing between each board (guides are provid-

ed on the template). Using a level, ensure the printed

template is level along the top edge and mark the hole

locations by piercing the template with a sharp pencil or

a screw at the center of the 3 hole locations.

Step 4: Install the Wall Anchors

Drill a 5/32 inch (4mm) pilot hole at each mark to deter-

mine whether to use provided drywall spiral anchors or

the wood screws.

For drywall mounting, use a Phillips head screw driver

to screw the Spiral Drywall Anchors into the wall at the

marked hole locations until the head of the anchor is ush

with the wall surface. Insert the screw using a Phillips

head screw driver until approximately 3/8” of the screw

remains sticking out of the anchor.

If hole location is over a wood stud, use the wood screw

only, inserting the screw using a Phillips head screw driv-

er until approximately 3/8” of the screw remains sticking

out of the wall.

Step 5: Hang the Board

Place the board against the wall with the keyhole hang-

ers lined up just above the screw heads sticking out of

the wall. Slowly slide the board against the wall until the

screw heads fall into the keyholes. Then pull rmly down

until the screw heads make a popping sound into the top

portion of the keyhole hanger.

Step 6: Repeat & Add Wine

Repeat with other boards and interchange colors and

styles as many times as you’d like. Display your favorite

bottles.

metal | wood infused collection

by VintageView

GRAIN ROD

Plo ttin g Gu id e

*We recomm end a minimum of 1/8”

spacing between boards

Add a Boa rd Below

Measure:

12 5/8“ + perferre d

spacing* from ma rks

1 & 2 on ea ch board

12 5/8” + perferre d

spacing* from ma rk 3

on ea ch board

Add a Boa rd

to the Left

Measure:

5 1/8” +

perferred

spacing* from

ma rk 1 to mark

2 on the left

boa rd

12 11/16“+

perferred

spacing* from

ma rk 3 on each

boa rd

Add a Boa rd to

the Right

Measure:

5 1/8” +

perferred

spacing* from

ma rk 2 to mark

1 on the right

boa rd

12 11/16“ +

perferred

spacing*

from ma rk 3

on ea ch board

Add a Boa rd Above

Measure:

12 5/8“ + perferre d

spacing* from ma rks

1 & 2 on ea ch board

12 5/8” + perferre d

spacing* from ma rk

3 on ea ch board

1 2

Produkt Specifikationer

Mærke:	VintageView
Kategori:	Ikke kategoriseret
Model:	GNR-LABEL2

Har du brug for hjælp?

Hvis du har brug for hjælp til VintageView GNR-LABEL2 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret VintageView Manualer

VintageView GNR-LABEL2 Manual

28 August 2024

VintageView GNR-LABEL3 Manual

28 August 2024

VintageView GNR-LABEL1 Manual

28 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

10 Oktober 2025

10 Oktober 2025

10 Oktober 2025

10 Oktober 2025

Oras Saga 3970 Manual

10 Oktober 2025

TOA AT-4030B-EB Manual

10 Oktober 2025

TOA VX-030DA Manual

10 Oktober 2025

TOA RS-481 Manual

10 Oktober 2025

TOA AT-4200B-EB Manual

10 Oktober 2025

Xerox DocuShare Manual

10 Oktober 2025