Vollrath 15059 Manual

Vollrath Skæremaskine 15059

Læs gratis den danske manual til Vollrath 15059 (12 sider) i kategorien Skæremaskine. Denne vejledning er vurderet som hjælpsom af 11 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 6 anmeldelser. Har du et spørgsmål om Vollrath 15059, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/12

Operator’s Manual

Redco

InstaCut

™

3.5 Tabletop and Wall Mount

2016 The Vollrath Company L.L.C. Part No. 2350022-1 ml 2/26/16

Please register your product at Vollrath.com

Thank you for purchasing this Vollrath equipment. Before operating the

equipment, read and familiarize yourself with the following operating

and safety instructions. SAVE THESE INSTRUCTIONS FOR FUTURE

REFERENCE. Save the original box and packaging. Use this packaging

to ship the equipment if repairs are needed.

SAFETY PRECAUTIONS

To ensure safe operation, read the following statements and understand

their meaning. This manual contains safety precautions which are

explained below. Please read carefully.

Warning is used to indicate the presence of a hazard that will or can

cause severe personal injury or death.

Caution is used to indicate the presence of a hazard that will or can

cause minor or major personal injury if the caution is ignored.

NOTICE: Notice is used to note information that is important but not

hazard-related.

To reduce risk of injury or damage to the equipment

• Check equipment before each use to insure the equipment is clean.

• Check for broken, nicked or dull blades and if found, replace the

blade assembly.

• Check to insure that the pusher head sits down completely on the

rubber bumpers.

• Check to ensure the rubber bumpers are in place. DO NOT USE

EQUIPMENT IF BUMPERS ARE NOT IN PLACE.

• On tabletop models the suction cups will hold the equipment

securely to smooth surfaces.

• Wall mounted equipment must be securely mounted to wall studs.

Use proper size and type hardware to mount equipment to wall.

• If necessary, lubricate guide rods using a light coating of mineral oil,

Petro Gel, or food grade lubricant. DO NOT USE COOKING OIL AS IT

WILL BECOME STICKY AND MAY PERMANENTLY DAMAGE THE

PUSHER HEAD BEARINGS.

FUNCTION AND PURPOSE

Intended for cutting, dicing and wedging vegetables and fruits.

UNPACKING THE EQUIPMENT AND INITIAL SETUP

Carefully remove crating or packaging materials from the equipment.

When no longer needed, dispose of all packaging materials in an

environmentally responsible manner.

Installing the wall mounted model

1. Use four (4) ¼" screws of a suitable length to secure the base to the

wall. Install screws into studs. If this is not possible, use proper

anchors and screws to secure base.

WARNING

CAUTION

Tabletop

Item No.

Wall Mount

Item No. Description

15000 15016 ¼" Dice

15001 15017 " Dice³⁄₈

15002 15018 " Dice½

15003 15019 4 Section Wedge

15005 15021 6 Section Wedge

15006 15022 8 Section Wedge

15007 15023 10 Section Wedge

15008 15024 12 Section Wedge

15009 — 6 Section Core

15010 15026 8 Section Core

2 Redco

InstaCut

™

3.5 Tabletop and Wall Mount Operator’s Manual

FEATURES AND CONTROLS

OPERATION

Prior to first use, it is important to clean the equipment. Wash new

blades with warm soapy water and rinse thoroughly to remove the thin

protective oil film. Before each use, check that the equipment is clean

and the blades are in good condition and bumpers are in place. If loose

or broken blades are found, blades must be serviced.

1. Before each use, always check for proper blade alignment. Slowly

set the pusher head onto the blade assembly. They should slide

together with no obstructions. If there are obstructions, verify they

are a matching set. Remove the obstruction.

2. Verify that the blade assembly and pusher head assembly are the

desired size.

3. Verify the bumpers are in place on the guide rods. DO NOT USE

EQUIPMENT IF BUMPERS ARE NOT IN PLACE.

4. Prepare the food product to be processed. The maximum size of the

food product is 3- " (8.9 cm) in diameter.½

5. Lift the handle and place the food on the blade assembly with the flat

side down.

6. Remove hand from the blade assembly area and place that hand on

the leg of the base on table top equipment, or on the wall for wall

mounted models.

7. Using a strong, quick, downward thrust, force the food product

through the blade assembly.

8. Repeat this process until you have prepared enough food product

for your daily needs.

9. Clean and lubricate your equipment immediately after each use. See

the section of this manual for more information.CLEANING

A Guide Rods. F Thumbscrew.Guides and align the pusher head onto the blade set. Used to secure the pusher head block or the blade assembly.

Handle. Used to lower and raise the pusher head block

G Pusher Head Bock. Pushes the food product through the blade set.

Specifically sized to match the corresponding blade assembly.

C Guides. Used for smooth and consistent operation of pusher head

on the guide rods

H Blade Assembly. Houses the blades. Specifically sized to match the

corresponding pusher head block

D Pusher Head Assembly. Made up of the pusher head block (and

“T” handle for tabletop models).

Base Assembly. Holds the guide rods and blade assembly.

E Bumpers. J Locking Pin.Cushions the stop of the pusher head. Secures the pusher head to the handle.

Wall Mount Model

Table Top Model

WARNING

Sharp Blade Hazard

Blades are sharp and can cause cuts. To avoid injury from

sharp blades, handle with caution.

Produkt Specifikationer

Mærke:	Vollrath
Kategori:	Skæremaskine
Model:	15059

Har du brug for hjælp?

Hvis du har brug for hjælp til Vollrath 15059 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Skæremaskine Vollrath Manualer

Vollrath 40950 Manual

25 August 2025

Vollrath 15059 Manual

25 August 2025

Vollrath Onion King 502N Manual

25 August 2025

Vollrath 40952 Manual

25 August 2025

Vollrath 15204 Manual

6 August 2025

Vollrath 15202 Manual

6 August 2025

Vollrath 15205 Manual

5 August 2025

Vollrath 15103 Manual

5 August 2025

Vollrath Instabloom II 15604 Manual

5 August 2025

Vollrath 55457 Manual

16 Juni 2025

Skæremaskine Manualer

Nyeste Skæremaskine Manualer

Bosch GOP 40-30 Professional Manual

12 September 2025

Axis AX-S12 Ultra Manual

10 September 2025

Optimum RK-1600 Manual

10 September 2025

Electrolux TRK70 Manual

9 September 2025

Axis AX-S14 Ultra Manual

9 September 2025

Primo PS-12D Manual

9 September 2025

Graef Master M94 Manual

7 September 2025

Russell Hobbs Aura Slice & Go Multi 22281-56 Manual

7 September 2025

Hendi 222614 Manual

4 September 2025

Primo PS-12 Manual

2 September 2025