Vollrath 40952 Manual

Vollrath Skæremaskine 40952

Læs gratis den danske manual til Vollrath 40952 (8 sider) i kategorien Skæremaskine. Denne vejledning er vurderet som hjælpsom af 10 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 5.5 anmeldelser. Har du et spørgsmål om Vollrath 40952, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

Operator’s Manual

Heavy-Duty Electric Slicers

2016 The Vollrath Company L.L.C. Part No. 350009-1 en 1/29/16

Please register your product at Vollrath.com

Thank you for purchasing this Vollrath equipment. Before operating the

equipment, read and familiarize yourself with the following operating

and safety instructions. SAVE THESE INSTRUCTIONS FOR FUTURE

REFERENCE. Save the original box and packaging. Use this packaging

to ship the equipment if repairs are needed.

SAFETY PRECAUTIONS

To ensure safe operation, read the following statements and understand

their meaning. This manual contains safety precautions which are

explained below. Please read carefully.

Warning is used to indicate the presence of a hazard that will or can

cause severe personal injury or death.

Caution is used to indicate the presence of a hazard that will or can

cause minor or major personal injury if the caution is ignored.

NOTICE: Notice is used to note information that is important but not

hazard-related.

To reduce risk of injury or damage to the equipment:

• Keep out of reach of children.

• Do not turn equipment on unless all guards are in place.

• Do not feed food by hand: always use food pusher.

• Equipment must be connected to a properly grounded electrical

supply matching the nameplate rating.

• Always unplug equipment before cleaning.

• Keep equipment away from water; avoid water jets during cleaning.

• Equipment should only be used in a flat, level position.

• Do not operate unattended.

• Install or locate this appliance only in accordance with the provided

installation instructions.

• Do not operate this appliance if it has a damaged cord or a plug, if it

is not working properly or if it has been damaged or dropped.

• Do not immerse the cord or plug in water. Keep the cord away from

heated surfaces. Do not let the cord hang over the edge of a table or

counter.

• Do not use an extension cord with this equipment. Do not plug this

equipment into a power strip or multi-outlet power cord.

• Have a qualified personnel install this equipment in accordance with

local codes and ordinances.

• Do not spray controls or outside of equipment with liquids or

cleaning agents.

• Do not clean the equipment with steel wool.

• Keep equipment and power cord away from open flames, electric

burners or excessive heat.

Item No. Model No. Description

Drive Peak HP Voltage Amps Hz Plug

40952 SLM300/S 12

"Blade Belt 1/2 120 2.0 60

NEMA

5-15P

WARNING

CAUTION

WARNING

Severe injury can occur if this equipment is not used properly.

2 Heavy-Duty Electric Slicers Operator’s Manual

FUNCTION AND PURPOSE

This equipment is intended to be used to slice food products in

commercial foodservice operations only. It is not recommended for use

with bone-in meat. It is not intended for household or laboratory use.

UNCRATE THE EQUIPMENT

1. Upon arrival, inspect the package and equipment for damage.

2. Immediately inform the carrier of any damage.

3. Position the pallet with the slicer on a flat surface.

4. Remove all packing material and tape, as well as any protective

plastic from the equipment.

5. Remove the sharpener. See “Disassemble the Slicer” on page 5.

6. Gently turn the slicer so it is resting on the blade cover knob.

7. Remove the four nuts that fasten the slicer to the pallet. Remove the

four washers and unscrew the four fastening tie rods from the pallet.

NOTICE: Take care to support the slicer so it does not tip when the

fastening hardware is removed.

8. Remove the pallet.

9. Install the metal spacers and rubber feet.

NOTICE: Feet and spacers must be installed to meet agency

listing criteria.

10.Upright the slicer and set on its feet.

11.Turn the feet to level the slicer.

Produkt Specifikationer

Mærke:	Vollrath
Kategori:	Skæremaskine
Model:	40952

Har du brug for hjælp?

Hvis du har brug for hjælp til Vollrath 40952 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Skæremaskine Vollrath Manualer

Vollrath 40950 Manual

25 August 2025

Vollrath 15059 Manual

25 August 2025

Vollrath Onion King 502N Manual

25 August 2025

Vollrath 40952 Manual

25 August 2025

Vollrath 15204 Manual

6 August 2025

Vollrath 15202 Manual

6 August 2025

Vollrath 15205 Manual

5 August 2025

Vollrath 15103 Manual

5 August 2025

Vollrath Instabloom II 15604 Manual

5 August 2025

Vollrath 55457 Manual

16 Juni 2025

Skæremaskine Manualer

Nyeste Skæremaskine Manualer

Bosch GOP 40-30 Professional Manual

12 September 2025

Axis AX-S12 Ultra Manual

10 September 2025

Optimum RK-1600 Manual

10 September 2025

Electrolux TRK70 Manual

9 September 2025

Axis AX-S14 Ultra Manual

9 September 2025

Primo PS-12D Manual

9 September 2025

Graef Master M94 Manual

7 September 2025

Russell Hobbs Aura Slice & Go Multi 22281-56 Manual

7 September 2025

Hendi 222614 Manual

4 September 2025

Primo PS-12 Manual

2 September 2025