WAC Lighting WS-12712 Manual

WAC Lighting Lys WS-12712

Læs gratis den danske manual til WAC Lighting WS-12712 (2 sider) i kategorien Lys. Denne vejledning er vurderet som hjælpsom af 28 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 14.5 anmeldelser. Har du et spørgsmål om WAC Lighting WS-12712, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
1WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
HARDWARE
A1 B1 C1 D1 E1 F1 G1
Wire Connector
Qty: 3 pcs
Allen Screw
Qty: 2 pcs + 1 Extra
Plastic Anchor
Qty: 2 pcs
Wood Screw
Qty: 2 pcs
Screw
Qty: 2 pcs + 1 Extra
Allen Wrench
Qty: 1 pc
Junction Box Screw
Qty: 2 pcs + 1 Extra
WARNING
IMPORTANT: NEVER attempt any work without shutting o the electricity.
- Read all instructions before installing.
- System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local regulations.
- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF”
the circuit breaker switch(es) that control the power to the xture or room that you are working on.
- Place the wall switch in the “OFF” position.
CAUTION
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are
worn out or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this xture.
CAUTION When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
- Lisez toutes les instructions avant d’installer.
- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les
règlements locaux.
- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt
(« OFF »).
- Placez l’interrupteur mural en position d’arrêt (« OFF »).
MISE EN GARDE
- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté
et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation ETL/CETL du
luminaire. MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression à la LED, tenir l’appareil par la seule base.
ADVERTENCIA
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e insta lación de esta
lámpara.
- Sistema está disenado para ser instalado por un electricista calicado, de acuerdo con el código eléctrico nacional y las normas locales.
- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de ali mentación
principal en la posición “OFF” (APAGADO).
- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
PRECAUCIÓN
- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni
utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calicación
ETL/CETL esta lámpara. PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la base sólo.
INSTALLATION INSTRUCTION
127 - LED Wall Sconce
WS-12712
2WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
FIG.1
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
Fig.2 Wiring
PREPARATION
1. Shut o the power at the circuit breaker and remove existing xture, including the crossbar.
2. Carefully unpack your new xture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.
MOUNTING THE FIXTURE (Fig. 2)
3. Remove the Allen screw (B1) with Allen wrench (F1) from the xture.
4. Drill a hole in the wall aligned with the key-hole located in the mounting plate, insert the plastic anchor (C1).
CONNECTING THE WIRES (Fig. 2)
5. Connect the driver input wire to junction box wires as shown in Fig. 2, making sure that all wire connectors (A1) are secured. If your outlet
box has a green or bare copper ground wire, connect the xture’s ground wire to it. Otherwise, connect the xture’s ground wire directly to
the back plate using the green screw provided. After wires are connected, tuck them carefully inside the junction box.
*Requires Driver to be recessed within the junction box.
6. Secure the mounting plate to the junction box using the junction box screw (G1). Fasten the mounting plate to the wall using the wood
screw (D1). The side of the mounting plate marked “GND” must face out.
MOUNTING THE FIXTURE (Fig. 1)
7. Remove the mounting screw (E1) from the xture, insert
crystal glass to the xture.
8. Place the cover on the crystal glass; secure it with mounting screw (E1).
Be careful not to screw it too tight to break the crystal.
9. Secure the xture onto mounting back plate with the Allen screw (B1)
using Allen wrench (F1).
Back Plate Dimensions
11”
1 3/8”
1 3/4”
F1
A1
C1
D1
G1
B1
E1
Allen Wrench
Wire Connector
Plastic Anchor
Wood Screw
Fixture
Cover
Crystal Glass
Junction Box
Screw
Ground Wire
Allen Screw Back Plate
Driver Junction Box
Mounting
Screw
INSTALLATION INSTRUCTION
127 - LED Wall Sconce
WS-12712

Produkt Specifikationer

Mærke: WAC Lighting
Kategori: Lys
Model: WS-12712

Har du brug for hjælp?

Hvis du har brug for hjælp til WAC Lighting WS-12712 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Lys WAC Lighting Manualer

WAC Lighting

WAC Lighting Tube Architectural DS-WD05-F27C-BK Manual

6 Juli 2025
WAC Lighting

WAC Lighting Archetype WS-W15924-BK Manual

5 Juli 2025
WAC Lighting

WAC Lighting DS-WS06 Manual

4 April 2025
WAC Lighting

WAC Lighting WS-W33125 Manual

4 April 2025
WAC Lighting

WAC Lighting WS-W11920 Manual

4 April 2025
WAC Lighting

WAC Lighting DS-WD08 Manual

4 April 2025
WAC Lighting

WAC Lighting WS-23018 Manual

4 April 2025
WAC Lighting

WAC Lighting DS-WD06 Manual

4 April 2025
WAC Lighting

WAC Lighting DS-WD05 Manual

4 April 2025
WAC Lighting

WAC Lighting WS-12712 Manual

4 April 2025

Lys Manualer

Nyeste Lys Manualer

Insignia

Insignia NS-LED8CT22 Manual

29 September 2025
Insignia

Insignia NS-STRL24FT3 Manual

29 September 2025
NEO Tools

NEO Tools 99-066 Manual

29 September 2025
BVB

BVB 05649 Manual

29 September 2025
Yongnuo

Yongnuo YNPAD100 Manual

29 September 2025
Litepanels

Litepanels Astra 6X Manual

29 September 2025
SmallRig

SmallRig RC 60C Manual

29 September 2025
SWIT

SWIT CL-M100C Manual

29 September 2025
Yongnuo

Yongnuo YN360 III Pro Manual

29 September 2025
SWIT

SWIT FL-C100D Manual

29 September 2025