Wagner Airless HEA Control Series 250M Manual

Wagner Spraymaling Airless HEA Control Series 250M

Læs gratis den danske manual til Wagner Airless HEA Control Series 250M (1 sider) i kategorien Spraymaling. Denne vejledning er vurderet som hjælpsom af 45 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 23 anmeldelser. Har du et spørgsmål om Wagner Airless HEA Control Series 250M, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

DOING A SPRAY TEST BEFORE

STARTING YOUR PROJECT

Before taking on your project simply take a piece of cardboard and do a

couple of spray tests. This will help you to achieve the right settings on the

paint sprayer:

× After installing the correct spray tip in the holder, try different

spray directions (e.g. vertical or horizontal) as shown by the arrow

on the tip.

× Adjust the pressure on the unit. While thicker materials (e.g. wall

paint) require more pressure, thinner ones (e.g. wood stains) need

less pressure.

× If your pattern is tailing, your spray tip might be incorrect, your spray

gun filter might be clogged or the paint is not diluted enough (for

further instructions see manual).

SPRAYING TIPS FOR EVEN

COVERAGE

× Spray at a constant speed and at an even distance from the surface.

The best distance is 20 to 30 cm between the spray tip and the

surface. For ceilings and hard to reach places WAGNER oers a wide

variety of accessories like extensions, longer hoses, etc.

× Make sure you are spraying at right angles to the surface. It is

important to move your entire arm back and forth rather than just

exing your wrist, otherwise one end of the pattern will be thicker

than the other and will cause overspray.

× The spray gun should be triggered by turning it on and o with each

stroke. Do not trigger the gun during the middle of a stroke. This will

result in an uneven spray and patchy coverage.

× Overlap each stroke by about 30 % for a smooth coating.

OTHER HELPFUL TIPS

× If you accidentally sprayed too much paint on one area, dab the paint

with a cloth or kitchen roll and spray another thin coat over it.

× During a break of several hours, it is not necessary to clean the entire

unit. The gun can be simply placed in a bucket with water to prevent

the paint in the tip from drying out. You should also cover up the paint

container to prevent the paint from drying out.

For more information, please read the relevant product manual

or visit our FAQs:

go.wagner-group.com/faqs-airless

MASKING AND COVERING

× If possible, empty the room completely. Alternatively, place all the

furniture in the middle of the room and cover it with a dust sheet.

× Cover the oor with a dust sheet, painter eece or cardboard.

× Use masking tape with an integrated drop sheet to cover up large

surfaces such as windows and doors.

× In addition test that the dust sheet does not utter when you get

close to it by just using the paint sprayer to blow air.

At WAGNER we have got you covered and have put together dierent

masking kits with all you need for a wide range of painting applications.

SET-UP

× Make sure to set up the Wagner unit properly (see manual).

CHOOSING THE CORRECT SPRAY

TIP AND FILTER

× For very thick materials, e.g. wall paints, we suggest using a 515, 517

or 619 tip with white lter.

× For thin materials, such as lacquers and stains, we recommend a 311

tip with red lter.

PREPARING COATING MATERIAL

Before putting the suction hose into the material, you need to prepare it:

× Most of the units can spray material straight from the container

without diluting. However, with some more viscous materials,

diluting by 5-10 % can give a better result (e.g. for a 10 L bucket 10 %

dilution means 1 L of water).

× If working with paint, make sure that it is approximately at room

temperature. Warm materials have more viscosity and are easier to

work with. However, do not go below or above the min./max.

temperature advised by the paint supplier.

× If there are any small particles in the paint such as dry paint from the

bucket, it is helpful to lter the paint to get rid of them.

× Dilute the paint with warm water (not hot!) or solvent for solvent-

based paints in accordance with manufacturer‘s instructions.

× Stir the material thoroughly with a stirring stick for at least 2 minutes.

In the case you are working with a bigger volume, e. g. 10 L bucket, it

is better to use a drill and a mixer therefor. Stir well, and always make

sure that there are no lumps in the paint, especially at the bottom

of the bucket. Some of the heavier materials in the paint can sink to

the bottem when the bucket has been standing for a longer time on

the shelve. When not mixed well, the lumps in the paint can clog the

paint sprayer.

In case of any questions, please do not hesitate to contact us directly:

HEA SPRAYING

TIPS & TRICKS

Produkt Specifikationer

Mærke:	Wagner
Kategori:	Spraymaling
Model:	Airless HEA Control Series 250M

Har du brug for hjælp?

Hvis du har brug for hjælp til Wagner Airless HEA Control Series 250M stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Spraymaling Wagner Manualer

Wagner Flexio 690 Manual

12 Juli 2024

Wagner W 240 Manual

6 Maj 2024

Wagner Airless HEA Control Series 250M Manual

30 Marts 2024

Wagner W 95 Manual

5 Februar 2024

Wagner WallPerfect W 925 E Manual

22 December 2023

Wagner WallPerfect Flexio 990 Manual

22 Oktober 2023

Wagner W 150 Manual

21 Oktober 2023

Wagner WallSpray Manual

30 August 2023

Wagner Project 115 Manual

8 Juli 2023

Wagner W 400 WallSprayer Manual

17 Juni 2023

Spraymaling Manualer

Nyeste Spraymaling Manualer

9 Juni 2025

8 Juni 2025

7 Juni 2025

6 Juni 2025

6 Juni 2025

4 Juni 2025

1 Juni 2025

31 Maj 2025

31 Maj 2025

31 Maj 2025