Watts MILUX RF Chrono-Thermostat Thermostaat Manual

Watts Termostat MILUX RF Chrono-Thermostat Thermostaat

Læs gratis den danske manual til Watts MILUX RF Chrono-Thermostat Thermostaat (18 sider) i kategorien Termostat. Denne vejledning er vurderet som hjælpsom af 14 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 7.5 anmeldelser. Har du et spørgsmål om Watts MILUX RF Chrono-Thermostat Thermostaat, eller vil du spørge andre brugere om produktet?

Side 1/18
USER GUIDE GB
RF basic thermostat WFHTRF 01 (20033)
TECHNICAL CHARACTERISTICS
MODES DESCRIPTION
LED INDICATOR
Red: - Heating indication (During consign adjustment)
Red Blinking: - 1 second cycle => Low batteries indication.
Green blinking: - Radio transmission (1 flash by transmission)
Room
setting.
Select
mode.
LED Indicator.
PPL IMP 1134A
Measured temperature
precision 0.1°C (or 0.2°F)
Operating temperature 0°C - 50°C (or 32°F – 122°F)
Setting temperature range 5°C – 30°C (or 41°F - 86°F)
Regulation
characteristics Proportional band 15min for 2°K
Electrical Protection Class II - IP30
Power Supply
Battery operated life 2 x 3V (CR2430)
~ 2 years
Radio frequency 433.92 MHz, <10mW.
certifications CE. EN 301489-1, EN 300220-1
(Radio frequency certifications)
Soft version V 2.0x
RADIO CONFIGURATION MODE
Batteries
- Turn the thermostat in Off position.
- To assign (*) the RF thermostat with the receiver you must put the
receiver in “RF init” mode (please refer to the receiver leaflet).
- After you have just made the thermostat in or mode.
The thermostat sends its configuration address by radio signal. (The
thermostat LED blinks green)
*
(
In this mode the thermostat should be near the receiver
)
- Radio frequency RF thermostat (433.92 Mhz) specially designed for water floor
heating.
- Personal code on each product.
- Equipped with a switch to select 3 different operating modes:
- Comfort (The thermostat follow the setting temperature)
- Off
-
Night reduction (The thermostat follow the setting temperature – 4°C)
- To be used only with ours receivers.
A
juste de temp.
ambiente
Selector de
modo
Indicador LED
Pilas
MANUAL DE USUARIO E MODO CONFIGURACIÓN POR RF
Termostato básico por RF WFHTRF 01 (20033)
CARACTERÍSTICAS TÉCNICAS
DESCRIPCIÓN DE MODOS
- Termostato por radiofrecuencia RF (433.92 Mhz), especialmente
diseñado para sistemas de calefacción por suelo radiante.
- Código personalizado en cada producto.
- Equipado con un interruptor para seleccionar el modo confort ( ),
apagado o reducción nocturna ( ).
- Para su utilización exclusiva con nuestros receptores.
INDICADOR LED
Rojo: - Indicación de calefacción (Durante la
configuración)
Rojo parpadeando: - Ciclo de 1 segundo => Indicación de batería baja.
Verde parpadeando: - Transmisión por radio (1 flash por transmisión)
Precisión de la medición 0.1°C (ó 0.2°F)
Temperatura de funcionamiento 0°C – 50°C (ó 32°F – 122°F)
Rango de ajuste de la temperatura 5°C – 30°C (ó 41°F - 86°F)
Características de regulación Banda proporcional de 2°K para un ciclo
de 15 minutos.
Protección eléctrica Clase II - IP30
Alimentación
Autonomía de las pilas 2 x 3V (CR2430)
~ 2 años
Frecuencia de radio 433.92 MHz, <10mW.
Certificaciones CE. EN 301489-1, EN 300220-1
(Certificaciones de radiofrecuencia)
Versión del software V 2.0x
- Gire el termostato hasta la posición Off.
- Para asignar (*) el termostato RF al receptor, debe ajustar éste último al
modo «RF init» (consulte la hoja técnica del receptor).
- Después de que haya ajustado el termostato al modo o , éste
enviará su configuración mediante una señal de radio. (El LED del
termostato parpadeará en verde)
*
(
En este modo, el termostato debe encontrarse cerca del rece
p
tor
)


Produkt Specifikationer

Mærke: Watts
Kategori: Termostat
Model: MILUX RF Chrono-Thermostat Thermostaat

Har du brug for hjælp?

Hvis du har brug for hjælp til Watts MILUX RF Chrono-Thermostat Thermostaat stil et spørgsmål nedenfor, og andre brugere vil svare dig