Watts WFHTRF 010 -20433 Manual

Watts Termostat WFHTRF 010 -20433

Læs gratis den danske manual til Watts WFHTRF 010 -20433 (2 sider) i kategorien Termostat. Denne vejledning er vurderet som hjælpsom af 14 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 7.5 anmeldelser. Har du et spørgsmål om Watts WFHTRF 010 -20433, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
USER GUIDE GB
RF basic thermostat WFHTRF 010 (20433)
TECHNICAL CHARACTERISTICS
MODES DESCRIPTION
- Radio frequency RF thermostat (433.92 Mhz) specially designed for water floor
heating. (Personal code on each product)
- Equipped with a LCD display to select comfort ( ), Off or night reduction ( )
mode.
- Setting and room temperature displayed.
- To be used only with ours receivers.
PPL IMP 1017A
Measured temperature precision 0.1°C (or 0.2°F)
Operating temperature 0°C - 50°C (or 32°F – 122°F)
Setting temperature range 5°C - 37°C by 0.5°C step (or 41°F - 99°F by 0.5°F step)
Regulation characteristics
Proportional Integral regulation (adjustable see installation
menu) Cycle: 15 minutes or Static differential 0.3°K
Anti-short cycle: 3min in OFF, 2min in ON.
Electrical Protection Class II - IP30
Power Supply
Battery operated life
2 x 3V (CR2430)
~ 2 years
Radio frequency 433.92 MHz, <10mW.
certifications CE. EN 300220-1, EN 301489-1
(Radio frequency certifications)
Soft version Displayed when the thermostat is turn Off
RADIO CONFIGURATION MODE
• To assign (*) the RF thermostat with the receiver you must put the receiver in
“RF init” mode (please refer to the receiver leaflet).
• After you have just Press key during 5 sec, when the display( rF “”)
• The thermostat sends its configuration address by radio signal.
• When the receiver is configured, Press key to return to user menu.
* (In this mode the thermostat should be near the receiver)
COMFORT operating mode:
Force comfort temperature operation indefinitely.
By pressing
&
keys the comfort temperature starts to blink and can be adjusted.
The measured temperature reappears after a few seconds.
OFF mode:
Use this mode if your Heating installation needs to be turned OFF.
The display is blank.
(Careful in this mode your installation can freeze)
Parameters are saved.
REDUCED operating mode:
Force reduced temperature operation indefinitely.
By pressing
&
keys the comfort temperature starts to blink and can be adjusted.
The measured temperature reappears after a few seconds.
1: Operating mode menu
2: Heater indication
3: Cooler indication
4: Batteries weak
5: If lit-up 6 displays the measured temperature
6: Measured temperature or set temperature
7: Moving bars when transmitting a radio signal
Or Title for installation Parameters (rF, J0,CLr…)
DISPLA
Y
Press the key during 5 seconds, Then use or keys to select the installation parameter to be adjusted.
Press to toggle the parameter setting or edit the value. If the value starts to blink you can use
&
keys to
adjust this value. Press & keys at the same time to reset this value to the factory default value. Once you have
adjusted the value press to validate this parameter value. When you have finished, use &
keys to go to
‘rF’ display and then press key to exit installation parameter menu.
rF : Radio configuration mode (see section). Press to return to normal operation modes.
J0 : °C / °F temperature display selection
J1 : “Hot” / “Cold” regulation mode. Select Hot for a Heater system, select Cold for a Cooling system
Cy : Proportional Integral regulation time cycle value in minutes (default: 15 minutes cycle)
bp : Proportional Integral regulation band amplitude value in degrees °C/°F (default: 2.0°C/3.6°F)
J5 : Select “PMP” to perform an 1 minute exercise everyday (if installation inactive during a day)
J6 : Air or Floor temperature regulation selection. (if no Floor sensor, regulation will use Air sensor)
J7 : “rEG” (Proportional Integral) or “HYs” (0.3°K Hysteresis) regulation type selection
Cp : compensation value in °C/°F (default: 2.0°C/3.6°F) this parameter must be adjusted by a professional.
Ao : Air sensor offset adjustment (default: no offset). Display measured Air sensor value
Fo : Floor sensor offset adjustment (default: no offset). Display measured Floor sensor value
FL : Floor temperature LOW limitation (default: 5°C/41°F), effective only if floor sensor present
FH : Floor temperature HIGH limitation (default: 28°C/82°F) , effective only if floor sensor present
CLr : Press key during 5s to reset all the WFHT LCD parameters to factory defaults
* (Default parameters are underlined.)
INSTALLATION PARAMETERS MENUS
Optional external sensor 10K

Produkt Specifikationer

Mærke: Watts
Kategori: Termostat
Model: WFHTRF 010 -20433

Har du brug for hjælp?

Hvis du har brug for hjælp til Watts WFHTRF 010 -20433 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Termostat Watts Manualer

Watts

Watts WFHTRF 010 -20433 Manual

14 August 2024
Watts

Watts Chrono Battery BT 051 Manual

6 August 2024
Watts

Watts BELUX-LIGHT - BT D-01 Manual

3 August 2024
Watts

Watts WFHTRF 01 -20033 Manual

2 August 2024
Watts

Watts BT-DPRF-02 Manual

23 Juli 2024
Watts

Watts MILUX RF Chrono-Thermostat Thermostaat Manual

23 Juli 2024
Watts

Watts Chrono Battery BT 050 Manual

21 Juli 2024
Watts

Watts BT 051 Chrono Battery Manual

2 Juni 2023
Watts

Watts BT-DRF-02 Manual

9 Oktober 2022

Termostat Manualer

Nyeste Termostat Manualer

Vimar

Vimar 09474 Manual

25 December 2025
Fantini Cosmi

Fantini Cosmi EC18RL Manual

18 December 2025
Fantini Cosmi

Fantini Cosmi L23EM1B Manual

17 December 2025
Fantini Cosmi

Fantini Cosmi Intellicomfort CH141AK Manual

16 December 2025
Fantini Cosmi

Fantini Cosmi Intellicomfort CH141E Manual

16 December 2025
Essentials

Essentials MATRIX Manual

2 December 2025
Honeywell

Honeywell CT62B Manual

1 December 2025
Honeywell

Honeywell X2P RTH20B Manual

28 November 2025
Honeywell

Honeywell RTH2CWF Manual

27 November 2025
Honeywell

Honeywell CT60A1036 Manual

27 November 2025