WyreStorm CON-H2-SCL Manual


Læs gratis den danske manual til WyreStorm CON-H2-SCL (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 23 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 12 anmeldelser. Har du et spørgsmål om WyreStorm CON-H2-SCL, eller vil du spørge andre brugere om produktet?

Side 1/4
2160p 4:4:4/60 In-Line HDMI Scaler with Audio Breakout
CON-H2-SCL Quickstart Guide
Copyright © 2019 WyreStorm Technologies | wyrestorm.com
CON-H2-SCL Quickstart Guide | 190617
UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)
support@wyrestorm.com
1 of 4
WyreStorm recommends reading through this document in its entirety to become familiar with the product’s features prior to starting the
installation process.
Basic Wiring Diagram
IMPORTANT! Installation Requirements
Advanced conguration of this product requires the use of the use of the
WyreStorm Management Suite v1.6 or higher conguration tool. Download
the latest version from the product page before continuing with the
installation.
Visit the product page to download the latest rmware, document version,
additional documentation, and conguration tools.
Read through the section for important wiring Wiring and Connections
guidelines before creating or choosing premade cables.
In the Box
1x CON-H2-SCL
1x DC 12V 2A Power Supply (US/UK/EU/AU)
3x 3-Pin Terminal Block
2x Mounting Brackets
1x Quickstart Guide (This Document)
MX-0404-H2A
Matrix
KEY
Passive HDMI
Control
Power
Digital Audio
CON-H2-SCL
Rear
CON-H2-SCL
Front
AC Mains
Audio Video
Receiver
HDMI to display
HDMI to display
HDMI to display
Control System
HDMI from
source
Blu-ray Player
Copyright © 2019 WyreStorm Technologies | wyrestorm.com
CON-H2-SCL Quickstart Guide | 190617
UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)
support@wyrestorm.com
2 of 4
Wiring and Connections
WyreStorm recommends that all wiring for the installation is run and terminated prior to making connections to the switcher. Read through this section in its
entirety before running or terminating the wires to ensure proper operation and to avoid damaging equipment.
IMPORTANT! Wiring Guidelines
The use of patch panels, wall plates, cable extenders, kinks in cables, and
electrical or environmental interference will have an adverse effect on
signal transmission which may limit performance. Steps should be taken
to minimize or remove these factors completely during installation for best
results.
WyreStorm recommends using pre-terminated HDMI cables due to the
complexity of these connector types. Using pre-terminated cables will
ensure that these connections are accurate and will not interfere with the
performance of the product.
.
RS-232 Guidelines
This product uses a 3-pin RS-232 with no hardware ow control. Most control
systems and computers are DTE where pin 2 is RX, this can vary from device
to device. Refer to the documentation for the connected device for pin
functionally to ensure that the correct connections can be made.
3rd Party Device
Pin 1 TX (Transmit) > To > RX (Receive)--- ---
Pin 2 RX (Receive) > To > TX (Transmit)--- ---
Pin 3 G (Gro d) > To > G (Gro d)un --- --- un
WyreStorm Co ectornn
Troubleshooting
No or Poor Quality Picture (snow or noisy image)
Verify that the output resolution of the source and display is supported by
this product.
If transmitting 3D or 4K, verify that the HDMI cables used are 3D or 4K rated.
Verify that all source and display connections are not loose and are
functioning properly.
No or Intermittent 3rd party Device Control
Verify that the RS-232 and Relay cables are properly terminated.
Refer to sections for pinout RS-232 Guidelines and/or Relay Wiring
information.


Produkt Specifikationer

Mærke: WyreStorm
Kategori: Ikke kategoriseret
Model: CON-H2-SCL

Har du brug for hjælp?

Hvis du har brug for hjælp til WyreStorm CON-H2-SCL stil et spørgsmål nedenfor, og andre brugere vil svare dig