AIYIMA T8 Manual

AIYIMA Modtager T8

Læs gratis den danske manual til AIYIMA T8 (2 sider) i kategorien Modtager. Denne vejledning er vurderet som hjælpsom af 29 personer og har en gennemsnitlig bedømmelse på 4.1 stjerner ud af 15 anmeldelser. Har du et spørgsmål om AIYIMA T8, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Telephone: 86-0755-28268551 VK: https://vk.com/aiyima

Location: 4F, Building 7 Hekan industrial park. Wuhe south road 41. Long-Gang district.

ShenZhen. CHINA. 518000

Website:www.aiyima.com Email: sale@aiyima.com

Shenzhen Yima Technology Co.,Ltd

Q & A

Bluetooth 5.0 TUBE 6N3

Headphone Preamplifier

USER MANUALS

Model T8:

① All my wires are connected. Why is there no sound?

1. Check whether the machine is turned on and whether it has switched to the

correspondinginput channel.

2.Check whether the back-end connection is correct and whether the volume is in

the minimum state.3. If all the above are normal, check whether the input playback

device is silent，paused，or the volume is at its minimum.

② Why can't I search for bluetooth pairing names?

Due to the design of this machine,bluetooth does not work when using other channels

for input.You just need to switch the input to Bluetooth mode.

④ Why is there a lot of electrical noise from the horn?

If you are not using the original standard power supply，please replace the power

supply andtest again.Many power supply ripple interference factor is large will cause

a lot of current sound.

③ ？Why does the sound break

Although this product is the front stage of DAC, it also has the function of amplification.

lf the volume of the rear stage device is turned up to the maximum, the volume of the

front stageis also turned up to the maximum, which is easy to distort. At this time，

you just need to turndown the volume of the front stage or the rear stage.

⑤ Why does the speaker make a loud buzzing sound when I plug in the input cord

and don't playthe audio source?

when the signal line without shield is used,the interference signal will enter the

poweramplifier for amplification. Replacing the signal line with shield can effectively

solve theinterference sound,or unplug the signal line.

Warning !

1. Do not open the shell without permission. Improper operation may damage the

machine or cause electric shock.

2. please use the regular manufacturer of switching power supply, otherwise there w

ill be the risk of damage to the machine.

3. Please do not change the vacuum tube at will, or it will burn out your vacuum tube

or machine.

4. Do not put the machine in a high temperature or humid environment.

Panel introduction

1 2

PC-USB 0peration instructions

1 OLED Display

2 IR

3.5mm Headphone Output(Priority)

Parameter

Chip

CM6642+ES9018+OPA1656+NJW1194

+QCC3031+6N3+MAX9722

PC-USB supports sampling rate

192K/24Bit

Distortion

RCA: 0.2%/HP: 0.003%

PC-USB support operating system

XP/W7/W8/W10/MAC/linux

Signal to noise ratio

RCA: 108dB/HP: 106dB

Headphone impedance

16~300Ω

Operating Voltage

DC 12V

Maximum output power

RCA:1.9V/HP: 120mW@32Ω

① Connect the PC-USB interface to the computer with the USB cable configured by

factory (USB supports hot plugging).

② Press the encoder knob to switch to PC-USB input.

③ As shown in the figure, find the icon with horn symbol in the lower right corner of

④ Right click the pop-up dialog box and click 【Playback devices】

⑤ Select the USB device recognized by PC from the pop-up dialog box (automatic

IDENTIFICATION of NATIVE USB; manual installation of driver is not required ).

⑥ Click the recognized digital output and set it as the default.

Remote Instruction

3 (1) Short Press:

* Power ON

* Input Mode Select

(2) Rotary Button: Volume Adjustment

(3) Long Press: Power OFF

(4) When the Headset and RCA output are connected at the same time:

* Double-click the button (Press it twice continuously) to switch to the

state of simultaneous output of the headset and RCA;

* Double-click again to switch back to the individual headphone output.

5 Bluetooth input

6 Audio output 7 Audio input

8 COA input

9 OPT input 10 PC-USB input

11 Power input(DC 12V)

Input sensitivity

Frequency response

20Hz~20kHz(±0.5dB)

Operation steps

① Connect the audio source you need to use to the audio source input interface

(switch the input channel to Bluetooth input when connecting bluetooth)

② Connect the back-end equipment that needs external connection to the audio

source output interface (such as power amplifier，active speaker,etc.)

③ Connect power supply (DC voltage shall not be higher than 12V)

④ Press the encoder knob to start the machine.

⑤ .Short press the knob to switch to the corresponding input channel to be used

⑥ . Turn the knob clockwise to select the desired volume

1 ON/OFF

2 Input Select

3 Mute

4 Bass+

5 Treble-

6 Treble+

8 Bass-

11 VOL-

12 VOL+

13 OLED ON/OFF

Produkt Specifikationer

Mærke:	AIYIMA
Kategori:	Modtager
Model:	T8

Har du brug for hjælp?

Hvis du har brug for hjælp til AIYIMA T8 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Modtager AIYIMA Manualer

AIYIMA D03 Manual

23 Juni 2025

AIYIMA A01 Pro Manual

23 Juni 2025

AIYIMA T8 Manual

23 Juni 2025

AIYIMA D05 Manual

23 Juni 2025

Modtager Manualer

Nyeste Modtager Manualer

Tams Elektronik SV-2 Manual

27 September 2025

Tams Elektronik B-6 Manual

27 September 2025

Neets 312-0003 Manual

27 September 2025

TV Star T7200 CX Manual

27 September 2025

Crestron DM-RMC-100-S Manual

24 September 2025

Ampetronic D14-2 Manual

24 September 2025

Audiolab D9 Manual

24 September 2025

Crestron DM-RMC-200-C Manual

24 September 2025

Ground Zero GZIA 2.240 Manual

24 September 2025

Crestron AMP-X750 Manual

24 September 2025