Akuvox E11R Manual

Akuvox Intercomsystem E11R

Læs gratis den danske manual til Akuvox E11R (2 sider) i kategorien Intercomsystem. Denne vejledning er vurderet som hjælpsom af 28 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 14.5 anmeldelser. Har du et spørgsmål om Akuvox E11R, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Allen Wrench x 1

Rope x 1

E11X x 1

ST4x20 screw x 4 Screw fixing seat x 4

M2.5x6 screw x 2Back cover x 1

Installaon

With 86 embedded box in the wall

Fix the wall-mounting bracket on

embedded box with two M4x30

screws.

Mark the two holes of the

wall-mounting bracket on the

wall.

Take down two M4x30 screws

and remove the wall-mounting

bracket.

Fix the wall-mounting bracket with two

ST4x20 screws and two M4x30 screws.

Insert two screw fixing

seats into the holes.

Use a hand drill with 5mm diameter bit to

make two 25mm depth holes in the

marked positions.

Step 2: Back cover Installaon Applicaon Network Topology

Fasten the back cover with four

M3x6 screws, then fix four

wall-mounting screws on the

back of E11X.

Conﬁguraon

For convenient wiring, hang

E11X on the wall-mounting

bracket with rope.

Make cables go through the back

cover, connecting to the corresponding

interfaces of the main board.

Without 86 embedded box in the wall

Universal Accessories:

Wall-mounting screw x 4

Step 1: Bracket/Box Installaon

Wall Mounng

23 4

1. Access the Web UI: Input the IP address into web browser to configure the phone.

2. Account Registration: On web UI, go to the path: page Account -> Basic

more information)

3. Configure the Push Button: On web UI, go to the path: Intercom -> Basic -> Push Button

to configure the call number.

4. Configure the code to open the relay: On web UI, go to the path: Intercom -> Relay

-> Relay ID/DTMF and choose the DTMF code number in corresponding area.

Rubber Plug x 3 S,M,L（）

Camera

RF card reader

Call buon&Status LED

Mic

E11X

Infrared sensor

Infrared LED

Photosensive sensor

Mark the four holes of the

wall-mounting bracket on

the wall for the screws.

Use a hand drill with 5mm diameter

bit to make four 25mm depth holes

in the marked positions.

Fix the wall-mounting bracket

with four ST4x20 screws.

Insert four screw fixing seats into

the holes.

Cable locking plate x 1

Note: For more LED settings, please refer to E11X webUI: Intercom -> LED Setting.

Network Video Recorder

(third party)

SIP Video Phone

LAN

PoE PoE

E11X E11X

PoE PoE

E11X E11X

PC(third party)

PoE PoE

Indoor Monitor

Speaker

Select a suitable size rubber plug

to push all the cables into the back

cover. Fix cable locking plate to

the back cover with two M2.5x6

screws.

After successful installation,

check the stability of device.

Insert the four wall-mounting screws on

the device into the corresponding holes

on the wall-mounting bracket, and then

press down to slide the wall-mounting

screws into the groove. Then use the

Allen Wrench to tighten the device with

two M3x6 screws.

TZ-SM-002038

陈凌谨

余芳

赵欣

2019.11.12

Operaon

Indicators

IP Announcement

Make a call:

1. Press the call button to call indoor SIP Phone.

2. During the talk, called party can press pre-configured code number to unlock the door.

Receive a call:

E11X supports Auto Answer by default. Incoming call will be answered automatically.

1. While E11X starts up normally, hold the call button for several seconds after the Status

LED turns blue, voice system will enter IP announcement mode.

2. In announcement mode, the IP address will be announced periodically.

3. Press Call Button again to quit the announcement mode.

4. In announcement mode, phone announces "IP 0.0.0.0" if no IP address is gained.

M3x6 screw x 6

M4x30 screw x 2 Wall-mounting bracket x 1

E11XE11X

E11X

E11X E11X E11X

E11 AK版挂墙快速安装指南

AKUVOX (XIAMEN) NETWORKS CO., LTD.

ADD: 10/F, NO.56 GUANRI ROAD, SOFTWARE PARK II, XIAMEN 361009, CHINA

www.akuvox.com

Notice Information

Akuvox E11X firmware contains third-party open source software under the terms of the GNU General Public

License(GPL). Akuvox is committed to meeting the requirements of the GNU General Public License (GPL) and will

make all required source code available.

The source code of software under the terms of GNU GPL can be downloaded online: http://www.akuvox.com/gpl.

Information contained in this document is believed to be accurate and reliable at the time of printing. This document is

subject to change without notice, any update to this document can be viewed on Akuvox’ s website:

Produkt Specifikationer

Mærke:	Akuvox
Kategori:	Intercomsystem
Model:	E11R

Har du brug for hjælp?

Hvis du har brug for hjælp til Akuvox E11R stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Intercomsystem Akuvox Manualer

Akuvox MD06 Manual

29 December 2024

Akuvox X916S Manual

13 August 2024

Akuvox E11R Manual

6 August 2024

Intercomsystem Manualer

Nyeste Intercomsystem Manualer

Viking E-40-SS-EWP Manual

28 Marts 2025

Viking E-1600-40-IPEWP Manual

27 Marts 2025

Hikvision DS-KH2230T Manual

27 Marts 2025

Viking E-1600-20A-EWP Manual

27 Marts 2025

Louroe Electronics AOP-SP-PB Manual

10 Marts 2025

2N Telecommunications 9151104 Manual

20 Februar 2025

2N Telecommunications Indoor Compact Manual

20 Februar 2025

Axis TI8202 Manual

20 Februar 2025

Axis TI8904 Manual

20 Februar 2025

Rollei Xtalk Manual

5 Februar 2025