Allen & Heath MixWizard3 14:4:2 Manual

Allen & Heath Ikke kategoriseret MixWizard3 14:4:2

Læs gratis den danske manual til Allen & Heath MixWizard3 14:4:2 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 49 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 25 anmeldelser. Har du et spørgsmål om Allen & Heath MixWizard3 14:4:2, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

WZ3 SYS-LINK Applications Note AP5736 1

SYS-LINK explained

SYS-LINK (system link) is the Allen & Heath connection standard for linking two consoles together to

expand the number of input channels feeding the mixes. One becomes the ‘slave’ to the other ‘master’

console. All the slave console mix busses including main LR, groups and auxes connect directly to the

master console mix busses without using up valuable input channels. The PFL/AFL system is also

linked so that all channels can be monitored using the master console headphones and meters. The

slave console master section is not used as its signals are taken before the mix inserts and output

faders. Both consoles must have the SYS-LINK option fitted. A single multiway cable is all that is

required to link the WZ3 to another Allen & Heath console fitted with SYS-LINK.

SYS-LINK versions 1 and 2

The MixWizard WZ3 uses the more recent SYS-LINK Version 2 standard. This benefits from balanced

interconnections which allow longer cable length with less chance of noise and interference pickup

than the earlier, unbalanced SYS-LINK Version 1. Both versions operate at -2dBu line level. V1 uses

the 25way D-type connector. V2 uses the 37way D-type connector. Two consoles fitted with SYS-LINK

V2 can be linked using a 36-core shielded cable wired one to one to two 37way male D-type

connectors. It is also possible to connect between SYS-LINK V2 and V1. This requires a 37way to

25way adapter cable wired to unbalance the connections. Wiring details are provided later. The

interconnecting cable is not included in the kit and should be sourced elsewhere or ordered separately

from Allen & Heath.

WZ316:2 / WZ312:2 / WZ320S SYS-LINK V2 output option

Option kit W312/16-SLV2 is available from Allen & Heath. This can

be installed in the WZ316:2, WZ312:2 or WZ320S console to provide

a SYS-LINK V2 output connection. Note that an input connection is

not provided. These consoles may be used as ‘slave’ channel

expanders only. For information on fitting the option refer to

document AP5735.

WZ314:4:2 SYS-LINK V2 input and output option

Option kit W31442-SLV2 is available from

Allen & Heath. This can be installed in the

WZ314:4:2 console to provide both SYS-LINK

V2 input and output. The console may be

used as either a ‘slave’ or a ‘master’. For

information on fitting the option refer to

document AP5737.

ALLEN&HEATH WZ3 SYS-LINK V2 AP5736 issue 3

Applications Note

2 WZ

3 SYS-LINK Applications Note AP5736

Linking consoles

SYS-LINK V2 to V2 connection

SYS-LINK V2 to V1 connection

37way male to 25way male D-type cable wired as shown below. Minimum 18-core shielded cable with

screen soldered to chassis at both ends. Maximum cable length 2.9 metres.

Custom applications

To connect other audio equipment using the SYS-LINK connectors always ensure unused audio inputs

are linked to 0V ground at the input connector. This is to prevent interference pickup on unterminated

high impedance inputs. Do not link unused outputs to ground. Connect line level signals of -2dBu.

Use balanced connections where possible. For unbalanced signals link signal ‘-‘ to 0V. To activate

PFL/AFL link PFL DC to 0V through a 15k ohm resistor (37 way Pins 3 to 1).

If you require further information or advice please contact Allen & Heath technical support.

Plug the ‘slave’ console SYS-LINK V2 output

into the ‘master’ console SYS-LINK V2 input.

Make sure the connectors are fully plugged

in and their securing screws tightened.

If one console has more than one SYS-LINK

connector, plug into the socket marked ‘A’.

37way male to male D-type cable wired

one to one. 36-core shielded cable with

screen soldered to pin 19.

Recommended cable length 2.9 metres,

maximum length less than 5 metres.

25way 37way 25way 37way

Pin 1 > 1 Pin 18 > 10

Pin 2 > 2 Pin 19 > 12

Pin 3 > 5 Pin 20 > 13

Pin 4 > 7 Pin 21 > 14

Pin 5 > 9 Pin 22 > 15

Pin 6 > 11 Pin 23 > 16

Pin 14 > 3 Pin 24 > 17

Pin 16 > 6 Pin 25 > 18

Pin 17 > 8

Pin 13 > 20 to 37 (linked 0V) (pin 13

also connected to 25way chassis)

37way Pin 19 = chassis

25way Pins 7 to 12,15 not connected

37way Pin 4 not connected

A suitable cable is available from Allen & Heath – part number AH6552

(Pin allocations shown are for ‘A’ connectors – adapter cable

is also suitable for ‘B’ connectors)

Produkt Specifikationer

Mærke:	Allen & Heath
Kategori:	Ikke kategoriseret
Model:	MixWizard3 14:4:2

Har du brug for hjælp?

Hvis du har brug for hjælp til Allen & Heath MixWizard3 14:4:2 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Allen & Heath Manualer

Allen & Heath IP4 Manual

4 Februar 2025

Allen & Heath dLive DM64 Manual

19 September 2024

Allen & Heath Studio 12 Manual

19 September 2024

Allen & Heath Scepter Manual

1 September 2024

Allen & Heath Avantis Manual

29 August 2024

Allen & Heath DL1000 Manual

15 August 2024

Allen & Heath iLive MADI 64 Manual

10 August 2024

Allen & Heath GS1 Manual

9 August 2024

Allen & Heath MPS9G Manual

6 August 2024

Allen & Heath DR128 Manual

5 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Planet Audio P100CPA Manual

15 Juni 2025

Sabrent BK-MAC2 Manual

15 Juni 2025

Planet Audio P9950CPA Manual

15 Juni 2025

Filmcity FC-CTH-01 Manual

15 Juni 2025

Cleveland 22CGT6 Manual

15 Juni 2025

Auray SVRK-4U-S Manual

15 Juni 2025

Bobrick B-2860 Manual

15 Juni 2025

Sony ODBK-103 Manual

15 Juni 2025

Planet Audio P70CPA Manual

15 Juni 2025

Gourmia GAF657 Manual

15 Juni 2025