American Dryer ExtremeAir EXT7-M Manual

American Dryer Håndstoffer ExtremeAir EXT7-M

Læs gratis den danske manual til American Dryer ExtremeAir EXT7-M (2 sider) i kategorien Håndstoffer. Denne vejledning er vurderet som hjælpsom af 19 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 10 anmeldelser. Har du et spørgsmål om American Dryer ExtremeAir EXT7-M, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

e treme irX A ®

MFD by AMERICAN DRYER, INC.

33067 INDUSTRIAL ROAD, LIVONIA, MI 48150, U.S.A.

Telephone (734) 421-2400 • Fax (734) 421-5580

www.americandryer.com • Email: sales@americandryer.com

Revised November 2011

e treme irX A

LIMITED WARRANTY

All parts of the

e treme irX A

models are warranted to the original consumer purchaser

to be free from defects in material and workmanship for a period of five (5) years from the

date of purchase from manufacturer. All models outside of the U.S.A., one (1) year includ-

ing sensor. We will replace FREE OF CHARGE, during the warranty period, any warranted

part which proves defective in material and/or workmanship under normal installation, use,

and service, excluding normal wear. Replacement parts can be obtained by returning the

part, TRANSPORTATION CHARGES PREPAID. You must notify factory prior to returning

part or dryer. Any damage to this dryer as a result of misuse, abuse, neglect, accident,

improper installation, unauthorized repairs, or any other use violative of instructions

furnished by us WILL VOID THIS WARRANTY. THIS LIMITED WARRANTY IS THE SOLE

WARRANTY ON OUR PRODUCTS, AND WE DISCLAIM AND EXCLUDE ANY AND ALL

OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES

OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. OUR LIABILITY

SHALL NOT EXCEED IN ANY EVENT THE REPLACEMENT OR SALE PRICE OF THE

ALLEGEDLY NONCONFORMING PRODUCT AND SHALL EXCLUDE LABOR CHARGES.

TO THE EXTENT PERMITTED BY LAW WE SHALL NOT BE LIABLE FOR ANY LOSS, COST,

EXPENSE, OR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND, WHETHER

BASED UPON WARRANTY (EXPRESS OR IMPLIED), CONTRACT, NEGLIGENCE OR

STRICT LIABILITY AND ARISING IN ANY WAY IN CONNECTION WITH THE DESIGN,

MANUFACTURE, SALE, USE OR REPAIR OF THE PRODUCT.

O ’ Mwner s anual

e treme irX A ®

Hand Dryers

F Ior nstallatIon or ervIce ssIstance s a

Please all c

(734) 421-2400 or

Email: sales@americandryer.com

ImPortant :H M & S N . rave odel erial o eady

m #______ s #______odel erIal

OPERATION AND MAINTENANCE OF YOUR DRYER

GENERAL OPERATION

This dryer is activated by an infrared sensor. The dryer operates as long as hands are below

the nozzle. There is a maximum 35-second running time with a safety over-ride feature if hands

are not removed. Each component used in your dryer has been designed to provide years of

trouble-free service. However, if trouble should develop, it can normally be located by visual

examination. Removal or replacement of most parts is simple and can be done without special

tools.

TROUBLE-SHOOTING:

IF THE DRYER WON’T TURN ON:

Check electrical service, circuit breaker. Make sure proper voltage is being supplied to the

dryer. Check for loose or disconnected terminals to sensor. INCREASE sensitivity (FIgure 3) by

inserting a flat-blade screwdriver through the hole and into the pot to CAREFULLY turn the

adjustment pot located on the sensor CLOCKWISE . If necessary, replace sensor.1/3 turn MAX

IF DRYER WILL NOT SHUT OFF:

Make certain black foam is attached to lens and lens is clean. If damaged, replace. DECREASE

sensitivity (FIgure 3) by inserting a flat-blade screwdriver through the hole and into the pot to

CAREFULLY turn the adjustment pot located on the sensor COUNTER-CLOCKWISE, 1/3 turn

MAX. If necessary, replace sensor.

GXT ONLY - IF COLD AIR IS COMING FROM THE NOZZLE:

Turn off breaker for 30 seconds to reset thermostat. If necessary, inspect heating element by

unfastening blower housing from backplate (3 screws). Remove heating element from blower

housing to inspect for damage. Replace if necessary.

IF NO AIR IS COMING FROM THE NOZZLE:

If the dryer also trips the circuit breaker, replace the motor/blower assembly by unfastening the

blower housing from the backplate (3 screws) and remove the inlet shield. Otherwise, replace

the sensor.

FOR ANY OTHER PROBLEM, CONTACT FACTORY FOR ASSISTANCE.

DISCONNECT POWER BEFORE SERVICING

DESUNA LA ELECTRICIDAD ANTES DE HACER REPARACIONES

WARNING:

CLEANING - DO NOT spray cleaning solvents through dryer vents. DO NOT use abrasive,

chlorinated, or highly alkaline cleaners. DO NOT use oil based cleaners.

SEMI-ANNUALLY remove the cover and clean all lint and dust from the mechanism, inside

of cover, and plastic window.

Clean cover with a mild soap or detergent and warm water, using a soft cloth or sponge.

1-7/8

INSTALLATION INSTRUCTIONS

1. Remove cover by removing (2) tamper-proof screws using security wrench supplied. Pull cover

directly toward you. IMPORTANT: save ecurIty rench s W .

2. Dryers should be placed at least 2 feet (61cm) apart and at least 12” (30cm) from washbasin.

Do not install dryer over washbasin. Dryers should be at least 18” (46cm) above any projection

which may interfere with the operation of the automatic sensor.

Hold the backplate to the wall at the suggested mounting height. Measure from MAXIMUM

bottom edge of the to the backplate floor (Ref. Dimension “A”, Figure 1)

3. Mark the locations of the four mounting holes and the conduit entrance location on the wall.

(The conduit entrance is the proper hole diameter for 1/2 inch (13mm) conduit.)

4. Fasten the backplate to the wall where previously marked. RECOMMENDATION:

Wood wall – No. 14 (M6) wood screws, 2-3/4” (70mm) long

Cement or brick – 1/4” (M6) stud expansion bolts, 3” (76mm) long

Hollow wall – 1/4” (M6) toggle bolts, length depends on wall thickness

5. Run a single phase 120V, 208V or 240V 50/60Hz electrical service to the dryer location using

either the in-wall or bottom surface 1/2"conduit entrance and connect to the lead wires as

shown on the dryer schematic. The ground wire must be connected to the dryer ground screw.

IMPORTANT: All units must be supplied with 3 wire service. Use No. 12 or 14 wire as required

by local electrical code. Unit must be installed by a qualified licensed electrician.

GXT - Connect each dryer to a dedicated 15 or 20 amp line. (120, 208 or 240V 50/60Hz)

EXT - Connect up to three dryers to one dedicated 20 amp line.

(120, 208 or 240V 50 Hz)

Dryers located in shower rooms or other wet locations should be equipped with ground fault

interrupter(s).

6. Adjusting Sound & Speed - The dryer is shipped set at maximum speed. Using a small flat

blade screwdriver, CAREFULLY turn the SPEED pot COUNTERCLOCKWISE 3/4 TURN MAX. to

REDUCE SOUND & SPEED. CAREFULLY turn CLOCKWISE to INCREASE SOUND & SPEED.

See figure 3.

7. Adjusting Sensitivity - The sensor is adjusted at the factory to turn on when hands are 4-6

inches away from the bottom of the dryer. To INCREASE SENSITIVITY turn the pot

CLOCKWISE up to 1/3 TURN MAX. To DECREASE SENSITIVITY turn the pot

COUNTERCLOCKWISE up to 1/3 TURN MAX. See figure 4.

8. Carefully replace the cover using (2) tamper-proof screws supplied. Apply a bead of caulk

around edges of cover to wall.

F digure 1 - ryer ouNtiNg M

(48mm)

(208mm)

6-3/16

7/8 (22mm) DIA. IN-WALL

& SURFACE CONDUIT

ENTRANCES

MOUNTING HOLES FOR

1/4” (M6) DIA. SCREWS

(227MM)

8-15/16

7/16

(11mm)

7/16

(11mm)

“A”

8-7/16

(214mm)

FLOOR

MAX MTG HT DIM. "A"

MEN 44"

WOMEN 42"

CHILDREN 32-42"

DISABLED 36"

F P ligure 2 - artS iSt

ITEM PART NO. DESCRIPTION

1 GXT202 COVER, WHITE ABS (MUST SPECIFY DRYER MODEL #)

2 GXT202-M COVER, WHITE STEEL

(MUST SPECIFY DRYER MODEL#)

3 GXT202-BG COVER, BLACK GRAPHITE STEEL (

MUST SPECIFY DRYER MODEL#)

4 GXT202-C COVER, CHROME PLATED STEEL

(SPECIFY DRYER MODEL #)

5 GXT202-SS COVER, STAINLESS STEEL

(SPECIFY DRYER MODEL #)

6 GXT212 NOZZLE ASS’Y W/LENS AND FOAM GASKET

7 GXT216 MOTOR/BLOWER

8 GXT218 HEATING ELEMENT (GXT9 MODELS ONLY)

9 SM239 SMART SENSOR COMPLETE, 100-240 VOLT

10 GB232 TAMPER-PROOF SCREWS & SECURITY WRENCH

F a S /S F 4 - a Sigure 3 - djuStiNg Peed ouNd igure djuStiNg eNSitivity

a S & SdjuStiNg ouNd Peed

The dryer is shipped set at maximum speed.

Turn counterclockwise to reduce sound and

speed. 3/4 of a turn max.

Screwdriver

Quieter Faster

Screwdriver

+ Sensitivity - Sensitivity

a SdjuStiNg eNSitivity

Place the screwdriver through the access hole

as shown to adjust sensitivity. Range is set at

the factory for 4 - 6 inches.

Produkt Specifikationer

Mærke:	American Dryer
Kategori:	Håndstoffer
Model:	ExtremeAir EXT7-M

Har du brug for hjælp?

Hvis du har brug for hjælp til American Dryer ExtremeAir EXT7-M stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Håndstoffer American Dryer Manualer

American Dryer Advantage AD90-BG Manual

17 August 2024

American Dryer Advantage AD90 Manual

16 August 2024

American Dryer ExtremeAir EXT7-M Manual

12 August 2024

American Dryer ExtremeAir EXT7-SS Manual

9 August 2024

American Dryer ExtremeAir GXT9-SS Manual

9 August 2024

American Dryer GX1-M Manual

8 August 2024

American Dryer Advantage AD90-M Manual

8 August 2024

American Dryer ExtremeAir GXT9 Manual

7 August 2024

American Dryer ExtremeAir EXT7 Manual

6 August 2024

American Dryer ExtremeAir GXT9-M Manual

6 August 2024

Håndstoffer Manualer

Nyeste Håndstoffer Manualer

Biodrier Biobot Manual

13 September 2024

Honeywell HPD-100B Manual

27 August 2024

Bobrick AirCraft B-750 Manual

23 August 2024

Bobrick QuietDry B-7120 Manual

23 August 2024

Bobrick QuietDry B-770 Manual

23 August 2024

Bobrick QuietDry B-7128 Manual

23 August 2024

Bobrick QuietDry B-778 Manual

23 August 2024

Bobrick CompacDryer B-710 Manual

23 August 2024

Noirot 2510 Automatic Manual

18 August 2024

Noirot 2511 Automatic Manual

18 August 2024