APC 19061CL-3F-1E Manual

APC UPS 19061CL-3F-1E

Læs gratis den danske manual til APC 19061CL-3F-1E (2 sider) i kategorien UPS. Denne vejledning er vurderet som hjælpsom af 48 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 24.5 anmeldelser. Har du et spørgsmål om APC 19061CL-3F-1E, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

APC Back-UPS Pro®

1000/1050/1100/1400

User’s Manual

990-2012F Revision 7 12/03

Installation and Initial Start-Up

To obtain warranty coverage, please fill out and

return the warranty registration card now.

Inspection

Inspect the UPS upon receipt. Notify the carrier

and dealer if there is damage. The packaging is

recyclable; save it for reuse or dispose of it

properly.

Placement

Install the UPS in a protected area that is free of

excessive dust and has adequate air flow. Do

not operate the UPS where the temperature and

humidity is outside the specified limits.

Warning: Changes or modifications to this

unit not expressly approved by the party

responsible for compliance could void the

warranty.

Connect to Utility

Check the Site Wiring Fault Indicator

Location: Top right corner of UPS back panel.

Caution: If the site wiring fault indicator lights,

get a qualified electrician to correct the building

wiring.

Connect the Loads

Plug the loads into the output connectors on the

rear of the UPS. To use the UPS as a master

“On/Off” switch, make sure that all of the loads

are switched “On”.

Caution: Do not connect a laser

printer to the Battery Backup Outlets.

Battery Backup Outlets: These UPS outlets

provide battery power and surge protection to

equipment when utility voltage is outside

acceptable limits. Data sensitive equipment such

as a computer, monitor, or external drive are

connected to these outlets.

Connect Telephone / Network Surge

Suppression (Optional)

Connect a single line telephone or a 10Base-T/

100Base-Tx network cable into the RJ-45/RJ-11

telephone/network surge protection “IN” jack on

the back of the UPS. Connect from the “OUT”

jack with telephone cable (supplied) or network

cabling (not supplied) to a fax modem or network

port.

Connect Computer Interface

Port (Optional, BP1050/1100)

PowerChute® plus power management software

is included with this UPS. Connect the supplied

interface cable to the 9-pin computer interface

port on the back panel of the UPS. Connect to

the computer. See software documentation for

installation instructions.

Charge the battery

The UPS charges its battery whenever it

is connected to utility power. The battery will

charge fully during the first 4 hours of normal

operation. Do not expect full runtime during this

initial charge period.

Operating Instructions

Switch “On” — Switch “Off”

With the UPS plugged in, press and

release the On/Off/Test button to supply

power to the loads.

The UPS loads are immediately powered while

the UPS performs a self-test. Press and release

the button again to turn “Off” power to the loads.

It may be convenient to use the UPS as a

master “On/Off” switch for the protected

equipment.

The on-line LED illuminates when the

UPS is supplying utility power to the

battery backup loads.

Self-test

The UPS performs a self-test automatically when

turned “On”, and every two weeks thereafter (by

default). Automatic self-test eliminates the need

for periodic manual self-tests.

During the self-test, the UPS briefly operates the

loads on-battery. If the UPS passes the self-test,

it returns to on-line operation.

If the UPS fails the self-test it

immediately returns to on-line operation

and lights the replace battery LED.

The loads are not affected by a failed test.

Recharge the battery overnight and perform the

self-test again. If the replace battery LED is still

"On”, replace the battery using the Replacing

the Battery procedure.

On-Battery

During on-battery operation, the on-

battery LED illuminates and the UPS

sounds an audible alarm consisting of 4

beeps every 30 seconds. The alarm stops when

the UPS returns to on-line operation.

Low Battery

When the UPS is operating on-battery and the

energy reserve of the battery runs low, the UPS

beeps continuously until the UPS shuts down

from battery exhaustion or returns to on-line

operation.

Overload

When loads exceed the UPS capacity,

the overload LED illuminates and the

UPS emits a sustained tone. The alarm

remains “On” until the overload is removed.

Disconnect nonessential load equipment from

the battery backup outlets, to eliminate the

overload.

If the overload is severe, the input circuit breaker

may trip (the resettable center plunger of the

circuit breaker pops out), as well. Disconnect

nonessential load equipment from the UPS to

eliminate the overload and press the plunger

back in to restart the UPS.

If there is AC power and the circuit breaker does

not trip during overload, the loads are still

powered. If the circuit breaker trips or the UPS

attempts to transfer to battery, the loads’ power

will be shut “Off”. Turn the UPS “Off” then back

“On” to power the loads.

Replace Battery

If the battery fails a self-test, the UPS

emits short beeps for one minute and

the replace battery LED illuminates.

The UPS repeats the alarm every five hours.

Perform the self-test procedure to confirm

replace battery conditions. The alarm stops

when the battery passes the self-test.

Shutdown Mode

If there is no power, the host connected to the

computer interface port can command the UPS

to shut down. This is normally done to preserve

battery capacity after a controlled shutdown of

the protected system. In shutdown mode the

UPS stops supplying power to the load. The on-

line and overload LED indicators flash alternately

or, if the UPS has shutdown due to a low battery,

the UPS will beep once every 4 seconds for

approximately 16 seconds. When line power is

restored, the UPS will return to on-line operation.

Cold Start

Note: Cold start is not a normal operating

condition.

When the UPS is “Off” and there is no utility

power, it is possible to cold start the UPS to

power the loads from the UPS battery.

• Press and hold the On/Off/Test button

until the UPS begins beeping.

• Release the On/Off/Test button during the

beeping to start the UPS.

APC, Back-UPS Pro, and PowerChute are registered

trademarks of American Power Conversion Corp. All other

trademarks are the property of their respective owner.

Storage

Storage conditions

Store the UPS covered and upright in a cool, dry location, with its battery fully

charged. Before storing, charge the UPS for at least 4 hours.

Extended storage

At -15 to +30 °C (+5 to +86° F), charge the UPS battery every 6 months

At +30 to +45 °C (+86 to +113° F), charge the UPS battery every 3 months.

Produkt Specifikationer

Mærke:	APC
Kategori:	UPS
Model:	19061CL-3F-1E

Har du brug for hjælp?

Hvis du har brug for hjælp til APC 19061CL-3F-1E stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

UPS APC Manualer

APC RBC150 Manual

2 April 2025

APC RBC151 Manual

2 April 2025

APC Symmetra LX 4kVA Manual

30 Marts 2025

29 Marts 2025

29 Marts 2025

29 Marts 2025

29 Marts 2025

30 Januar 2025

30 Januar 2025

APC BE650G2-IT Manual

14 Januar 2025

UPS Manualer

Nyeste UPS Manualer

Teltonika BAT120 Manual

30 Januar 2025

LevelOne UPS-2101 Manual

9 Januar 2025

Conceptronic ZEUS52E6K Manual

31 December 2025

Conceptronic ZEUS51E6K Manual

31 December 2025

CyberPower Smart App Sinewave PR2000RT2U Manual

30 December 2025

Tripp Lite ECO750UPS Manual

30 December 2025

Phoenix Contact QUINT-UPS/ 24DC/ 24DC/10 Manual

28 December 2024

Phoenix Contact QUINT-UPS/ 24DC/ 24DC/20 Manual

28 December 2024

Phoenix Contact QUINT-UPS/ 24DC/ 24DC/ 5 Manual

28 December 2024

Conceptronic ZEUS52EA3K Manual

14 December 2024