APC Back-UPS BX550CI-AR Manual

APC UPS Back-UPS BX550CI-AR

Læs gratis den danske manual til APC Back-UPS BX550CI-AR (4 sider) i kategorien UPS. Denne vejledning er vurderet som hjælpsom af 29 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 15 anmeldelser. Har du et spørgsmål om APC Back-UPS BX550CI-AR, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Installation and Operation

Back-UPS BX550CI-AR

Safety

Installation

Connect the Battery

Pull down on the battery connector handle, and then push it into the unit.

Connect Equipment

Connect equipment to the battery and surge protected outlets. These outlets

provide battery backup power and surge protection to all connected equipment.

Connect AC Power Cord

Connect the Back-UPS power cord directly into a wall outlet.

Turn on the Back-UPS

Press the Power ON button located on the front of the Back-UPS. The Power On LED will illuminate and a

single short beep will be audible to indicate that the Back-UPS is providing protection for connected

equipment.

The Back-UPS battery charges fully during the first 10 hours while connected to utility power. The Back-UPS

battery will charge while the Back-UPS is switched on or off and is connected to utility power. Do not expect

full battery run capability during the initial charge time.

This unit is intended for indoor use only.

Do not operate this unit in direct sunlight, in contact with fluids, or where there is

excessive dust or humidity.

Be sure the air vents on the unit are not blocked. Allow adequate space for proper

ventilation.

Environmental factors impact battery life. High temperatures, poor quality A/C power,

and frequent, short duration discharges will shorten battery life.

Connect the Back-UPS directly to a wall outlet. Do not use surge protectors or

extension cords.

1ON/OFF button

2Battery connector

3Circuit breaker

4Input power cord

5Battery and surge protected outlets

bu195a

Transfer Voltage and Sensitivity Settings

Automatic Voltage Regulation boosts the utility voltage when it drops below safe levels. This allows the equipment

that is connected to the unit to operate during low voltage conditions. It will also regulate high voltage down to

safer levels.

The Back-UPS will switch to battery power if the input voltage level becomes too low for the Automatic Voltage

Regulation feature to compensate, or if the utility power is distorted.

If the Back-UPS switches to battery power too frequently or too infrequently, adjust the transfer voltage and

sensitivity settings:

1. Turn off the Back-UPS. Plug it into utility power.

2. Press and hold ON/OFF until the LED repeatedly flashes. The unit is now in Program Mode.

3. Release the button. The LED will flash once, twice, or three times per second, indicating the current

setting.

4. Press ON/OFF within two seconds to change the setting. Each time the button is pressed, the LED will

flash at a different rate: once, twice, or three times per second, indicating the new setting. Continue

pressing the button until the desired setting is reached. If the button is not pressed within five seconds, the

Back-UPS will exit the Program Mode.

Status Indicators

LED Flashing

Transfer

Voltage Setting

Input Voltage

Range Usage

Once per second Low 155 - 280 The Back-UPS will switch to battery power less often. Use

with equipment that is not sensitive to low or high level

voltage levels or minor voltage waveform distortions.

Twice per second Medium

(factory default)

160 -280 Default, use in normal conditions.

Three times per second High 165 - 270 The Back-UPS will switch to battery power during any

small fluctuation in voltage. Use with equipment that is

sensitive to low or high level voltage levels or minor voltage

waveform distortions.

LED Audible Alarm Condition

On Off Online - Back-UPS is supplying conditioned utility power to the connected

equipment

Constant Tone On Line Overload - The power drawn by the connected equipment exceeds the

power capacity of the unit

On (Off during

4 beeps)

4 beeps repeated

every 30 seconds

On-Battery - Back-UPS is supplying battery power

Flashing Rapid Beeping

(every 1/2 second)

Low Battery Warning - There are 2 minutes of run time remaining

Constant tone Bad Battery Detected - Battery needs to be charged, or is at end of life. (See

Battery Replacement.)

Chirp every 2

seconds

Charger Warning -Back-UPS has experienced an internal problem, but

continues to power the load. Contact APC Technical Support

Off Short beep every

4 seconds

Low Battery Shutdown - During On Battery operation the battery power was

almost completely exhausted, and the Back-UPS is waiting for utility power to

return to normal

Constant Tone On Battery Overload - Connected equipment requires more power than provided

by the Back-UPS battery. Unplug devices one at a time to remove overload, if not

corrected Contact APC Technical Support

Constant Tone Charger Fault - Back-UPS has an internal problem, and is no longer powering

the load. Contact APC Technical Support

Produkt Specifikationer

Mærke:	APC
Kategori:	UPS
Model:	Back-UPS BX550CI-AR

Har du brug for hjælp?

Hvis du har brug for hjælp til APC Back-UPS BX550CI-AR stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

UPS APC Manualer

APC RBC150 Manual

2 April 2025

APC RBC151 Manual

2 April 2025

APC Symmetra LX 4kVA Manual

30 Marts 2025

29 Marts 2025

29 Marts 2025

29 Marts 2025

29 Marts 2025

30 Januar 2025

30 Januar 2025

APC BE650G2-IT Manual

14 Januar 2025

UPS Manualer

Nyeste UPS Manualer

Teltonika BAT120 Manual

30 Januar 2025

LevelOne UPS-2101 Manual

9 Januar 2025

Conceptronic ZEUS52E6K Manual

31 December 2025

Conceptronic ZEUS51E6K Manual

31 December 2025

CyberPower Smart App Sinewave PR2000RT2U Manual

30 December 2025

Tripp Lite ECO750UPS Manual

30 December 2025

Phoenix Contact QUINT-UPS/ 24DC/ 24DC/10 Manual

28 December 2024

Phoenix Contact QUINT-UPS/ 24DC/ 24DC/20 Manual

28 December 2024

Phoenix Contact QUINT-UPS/ 24DC/ 24DC/ 5 Manual

28 December 2024

Conceptronic ZEUS52EA3K Manual

14 December 2024