Atdec SD-SA-DK-DB-BK Manual

Atdec Ikke kategoriseret SD-SA-DK-DB-BK

Læs gratis den danske manual til Atdec SD-SA-DK-DB-BK (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 21 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 11 anmeldelser. Har du et spørgsmål om Atdec SD-SA-DK-DB-BK, eller vil du spørge andre brugere om produktet?

Side 1/4
Installation Instructions
SPACEDEC ACROBAT
SWING ARM DOUBLE
Swing Arm
Assembly (x2)
Cable Wrap
Applicator (x1)
Top Cap Tool (x1)
Key (x1)
Cable Clip
(x4)
Extension
Clip (x8)
Bits Box
Mounting Fasteners
M4x10mm
Screw (x8)
M4x12mm
Screw (x8)
M4x16mm
Screw (x8)
16mm Cable
Wrap (x2)
Washer (x1)
Base Casting (x1)
Spacer Tube
Assembly (x2)
M8 Interscrew
(x1)
M8 Nyloc Nut (x1)
Cable Manager
Tube Clip (x1)
5mm Allen
Key (x1)
M4x16mm
Countersunk
Screw (x3)
Desk Clamp Box
M8 Desk Clamp
Screw (x1)
Pressure
Plate (x1)
Inner Tube Post
Desk Clamp
Bracket (x1)
Component Checklist
Threaded Rod
and Top Cap
(x1)
Possible Configurations
Spacedec Acrobat Swing Arm Double can be
assembled in a number of different configurations
depending on the users requirements.
Two such examples are shown below and right.
Arm, Spacer, Arm, Spacer
Side by side displays
Arm, Arm, Spacer, Spacer
Back to Back displays
Spacer Tube (x2)
Internal Tube Post
Top Cap and
Threaded Rod
C
C.1. Desk Clamp
To assemble the Desk Clamp Assembly, first place the
M8 Nyloc Nut inside the Base Casting with the Plastic
Ring facing down, then screw the Base Casting on to the
Desk Clamp Bracket using the M4x16mm Countersunk
screws.
C.1.1. Assemble the Desk Clamp
C.1.2. Attaching the Desk Clamp
Tighten
Firmly
Base Casting
Desk Clamp
Assembly
Desk Top
Pressure Plate
M8 Desk Clamp Screw
5mm Allen Key
Adjust the Desk Clamp to suit your desk thickness by
turning the M8 Desk Clamp. Screw with the supplied
5mm Allen Key
Suits 12mm (
1
/
2
”)
to 38mm (1
1
/
2
”)
thick work
surfaces
Pressure Plate
M8 Desk
Clamp Screw
C.1.3. Attaching the Swing Arm Post
Use the Top Cap Tool to tighten the Threaded
Rod into the Base Casting as shown below.
Top Cap
Tool
Threaded
Rod
Base
Casting
NOTE: Desk Clamp
Assembly is suitable
for square edged
desks only.
Tighten
Firmly
NOTE: It is
recommended
that the Desk
Clamp be
attached to
the rear or
side edge
of the work
surface
DESK CLAMP ADJUSTMENT RANGE
M4x16mm
Countersunk
Screw (x3)
Base
Casting
Desk
Clamp
Bracket
M8 Nyloc
Nut
Component Checklist
A
Check you have received all parts against the Component Checklist on the previous page.
Assemble the Arm
B
Threaded Rod
and Top Cap
Swing Arm
Assembly
(x2)
Internal Tube Post
Spacer Tube
(x2)
Cable Manager
Tube Clip
B.2. Assemble
the Swing Arm
Assemble the Swing Arm in
the desired configuration
ensuring all components
are used as shown.
You will need to disassemble the Tube Assembly
before assembling the Swing Arm
B.1. Disassemble the Tube Assembly
Mounting Options


Produkt Specifikationer

Mærke: Atdec
Kategori: Ikke kategoriseret
Model: SD-SA-DK-DB-BK

Har du brug for hjælp?

Hvis du har brug for hjælp til Atdec SD-SA-DK-DB-BK stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Atdec Manualer

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Elektrobock

Elektrobock PT44 Manual

14 September 2025
BSS Audio

BSS Audio FDS-366T Manual

14 September 2025
Systemair

Systemair Airline R-114 Manual

14 September 2025
IFM

IFM SU2031 Manual

14 September 2025
IMC Networks

IMC Networks 232CL9R Manual

14 September 2025
Melissa & Doug

Melissa & Doug 9336 Manual

14 September 2025
Opus

Opus dataPREDATOR Manual

13 September 2025