Atdec SD-SA-DW-S Manual

Atdec Ikke kategoriseret SD-SA-DW-S

Læs gratis den danske manual til Atdec SD-SA-DW-S (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 18 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 9.5 anmeldelser. Har du et spørgsmål om Atdec SD-SA-DW-S, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Component Checklist

Installation Instructions

SPACEDEC ACROBAT

SWING ARM WALL

Swing Arm

Assembly (x1)

Cable Wrap

Applicator (x1)

Top Cap Tool (x1)

2.5mm Allen

Key (x1)

Cable Clip

(x2)

Extension

Clip (x4)

Component Checklist

Check you have received all parts against the Component Checklist above.

Bits Box

Mounting Fasteners

M4x10mm

Screw (x4)

M4x12mm

Screw (x4)

M4x16mm

Screw (x4)

16mm Cable

Wrap (x1)

M6 Washer (x3)

Direct Wall Mount

Bracket Assembly (x1)

Top Cap

Threaded Rod

Bottom Cap

Direct Wall Mount

Bracket

5mm Allen

Key (x1)

Nylon Anchor

Plugs (x3)

M6x40mm

Coach Screw (x3)

Direct Wall Mount

Timber Stud

Wall

Direct Wall Mount

Bracket

4mm Hole

M6 Washer

M6 Coach Screw

Direct Wall Mount

Bracket

8mm Hole

M6 Washer

M6 Coach Screw

B.2.1.B.1.2.

B.1. For Timber Stud Mounting - Use the Direct Wall

Mount Bracket to mark out the location of the required

three holes (see diagram B.1.1.). Drill 3x4mm holes deep

enough to receive the M6 Coach Screws, insert the screws

and secure the bracket to the wall (see diagram B.1.2.)

B.2. For Masonry Mounting - Use the Direct Wall Mount

Bracket to mark the location of the required three holes (see

diagram B.1.1.). Using an 8mm masonry drill bit, drill 3 holes

41mm deep. Insert the Nylon Anchors and then secure the Bracket

to the wall using the M6 Coach Screws (see diagram B.2.1.).

S8 Nylon Anchor

Refer to Ergonomic guidelines overleaf to determine best position to mount wall bracket.

Front View of the Direct Wall

Mount Bracket

B.1.1.

Note: Ensure Bracket is

mounted Vertically

Brick or Concrete Wall

Attaching the Cable Wrap to the Arm

E.1. Position the display at its highest possible position to ensure that there is sufficient cabling at the end of the

arm so the cables are not stretched or pulled out when the display is moved.

BEFORE PROCEEDING TO THE NEXT STEP PLEASE NOTE:

Swing Arm Wall will only work when a display is properly installed.

DO NOT adjust tension screws or gas strut until your display has been attached.

Cable Clips

Display at

highest point

E.1.

Direct Wall Mount Continued.

Tighten

using the

Top

Cap Tool

Insert

Threaded

Rod and

Top Cap

Direct Wall

Mount

Bracket

Plastic

Bottom

Cap

Arm with

inner tube

B.3.1.

Attaching the Display

75mm x 75mm (3” x 3”) mounting hole pattern

Display

M4x10mm

Screws

75mm

(3”)

75mm (3”)

100mm x 100mm (4” x 4”) mounting hole pattern

NOTE:

Ensure that the

flat side of each

Extension Clip sits

against the back

of the display

Extension Clip

Select:

M4x12mm or

M4x16mm Screws

100mm

(4”)

100mm (4”)

Display

Installing Cable Management

D.1.

Push the two supplied Cable Clips into the holes on the underside of the arm as shown.

D.2.

Feed the cables into the Cable Wrap Applicator.

D.3.

Insert the Cable Wrap Applicator into the Cable Wrap as shown.

D.4.

Squeeze the nose of the Applicator and place inside the Cable Wrap ensuring that the opening edges of

the Cable Wrap face towards the nose of the applicator as shown in diagram.

D.1.

Push in

Clips

Nose

D.2. D.3.

D.4.

B.3. Attach the Spacedec

Arm to the Direct Wall Mount

Bracket. (see diagram B.3.1.)

Tighten the Top Cap with the

supplied Top Cap Tool.

(see diagram B.3.2)

B.3.2.

Tighten

Produkt Specifikationer

Mærke:	Atdec
Kategori:	Ikke kategoriseret
Model:	SD-SA-DW-S
Dybde:	350 mm
Produktfarve:	Sølv
Montering:	VESA 4"x4" & VESA 3"x3"
Skærmstørrelse kompatibilitet:	12/24 "
Maksimal vægtkapacitet:	9 kg
Drejevinkel:	40 °