Atdec TH-400-LED Manual

Atdec Ikke kategoriseret TH-400-LED

Læs gratis den danske manual til Atdec TH-400-LED (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 20 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 10.5 anmeldelser. Har du et spørgsmål om Atdec TH-400-LED, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Component Checklist

Step 1. Component Checklist

Check you have received all parts against the Component Checklist above.

Hardware

Mounting Fasteners

M8 x 20mm

Screw (x4)

M8 x 40mm

Screw (x4)

Cable Access

Support (x1)

Step 2. Attach Wire Mount to the Display

Note: This product is suitable for LED/LCD displays with VESA mounting hole configurations 400mm (16”) wide, supporting a

maximum weight of 50 kg (110 lbs).

TH-400-LED



LED Slim Wall Mount

Installation Instructions

Nylon

Anchor (x2)

M6 Washer

(x2)

M8 Washer

(x4)

Dry Wall

Anchor (x2)

Wall Mount

Screw (x2)

M8 Spring

Washer (x4)

Attach the Wire Mount components to the Display

using the hardware supplied.

TOOLS REQUIRED:

UÊ*ÜiÀÊÀ

UÊ*ps Head Screw Driver

UÊ{Ê

”) Drill Bit

UÊnÊ

”) Masonry Drill Bit

UÊ£äÊ

”) Drill Bit

Ê*>Ìi

(x2)

Support (x1)

Wire Mount (x1)

Spacer Bush (x4)

Top of

Display

Spacer Bush

(x4)

Recessed

Mounting Hole

TWIST

M8 Spring

Washer (x4)

M8 Washer

(x4)

M8 x 20mm

Screw (x4)

Display

Cable Access

Support

Wire Mount

Recessed Mounting Holes or

Display with a Curved Rear Panel

If the Mounting Holes are recessed into the

back of the Display, or the Display has a

curved rear panel, use the Spacer Bushes

supplied to pack the Mounting Holes.

NOTE: Use the longer Mounting

Fasteners (M8 x 40mm) supplied.

M8 x 40mm

Screw (x4)

Back of Display

TIP: Ensure that the

Wire Mount is taut by

twisting the ends.

Step 3. Mount the Hook Plates on the Wall

Choose from one of the following Mounting options (see below), , Timber Stud Masonry Wall Dry Wall, or . Fasten the Hook Plates

180-200mm (7-7

”) apart, using the appropriate Mounting Hardware supplied to suit the type of wall.

Timber Stud Dry Wall

Step 4. Hang the Display on the Wall

180-200mm

(7-7

”)

Drill two holes 50mm deep using a

4mm drill bit.

Drill two holes 50mm deep using an

8mm Masonry drill bit.

Hook Plate

(x2)

Wall Mount

Screw (x2)

Hook Plate

(x2)

Nylon Anchor

(x2)

M6 Washer

(x2)

Hook Plate

(x2)

Drill two holes 60mm deep using a

10mm drill bit.

Dry Wall Anchor

(x2)

M6 Washer

(x2)

Step 5. Cable Access

( required)

1. Lift the Display so that the

Wire Mount is above the

Hook Plates.

2. Push the Display in, so

that it touches the wall.

3. Gradually lower the

Display until it is hanging

from the Hook Plates.

Installation Complete

Connect

Cables

Fold out Cable

Access Support

Pull the Display

out from the wall

No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent of Atdec Pty Ltd.

Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published: 09.12.09 ©

Wall Mount

Screw (x2)

Fold in Cable

Access Support

Return Display

to flat position

Masonry Wall

Produkt Specifikationer

Mærke:	Atdec
Kategori:	Ikke kategoriseret
Model:	TH-400-LED
Vægt:	50 g
Produktfarve:	Sort
Monteringstype:	Væg
Montering interface kompatibilitet (min.):	400 x 200 mm
Montering interface kompatibilitet (maks.):	400 x 400 mm