Atlona AT-HDR-EX-70C-TX Manual

Atlona Ikke kategoriseret AT-HDR-EX-70C-TX

Læs gratis den danske manual til Atlona AT-HDR-EX-70C-TX (8 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 6 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 3.5 anmeldelser. Har du et spørgsmål om Atlona AT-HDR-EX-70C-TX, eller vil du spørge andre brugere om produktet?

Side 1/8
1
AT-HDR-EX-70C-TX
4K HDR HDBaseT Transmitter with Control
AT-HDR-EX-70C-TX
The Atlona AT-HDR-EX-70C-TX is a HDBaseT™ transmitter for 4K and high dynamic range (HDR)
content. It supports extension of 4K/UHD video @ 60 Hz with 4:4:4 chroma sampling plus HDR
data, multi-channel audio, control signals, and power up to 130 ft (40 m) or 1080p up to 230 ft
(70 m) over Category 6/6A cable.
The HDR-EX-70C-TX is ideal for use with the AT-HDR-EX-70C-RX receiver for transmitting 4K
HDR in point-to-point applications. It can also be used with the AT-UHD-CLSO-824 and AT-
UHD-SW-5000ED for transmitting 4K/UHD @ 60 Hz 4:2:0 signals to the switchers from a remote
source.
IMPORTANT: Visit https://atlona.com/product/at-hdr-ex-70c-tx for the latest rmware
updates and Installation Guide.
1 x AT-HDR-EX-70C-TX
2 x Mounting brackets
4 x Mounting screws
1 x 48V DC power supply
1 x 2-pin captive screw connector
1 x 3-pin captive screw connector
1 x 4-pin captive screw connector
Package Contents
Installation Guide
2
AT-HDR-EX-70C-TX
DC 48V
-
+
RS-232
RX TX
SS
HDBaseT OUT
HDMI IN
IR OUTIR IN
AT-HDR-EX-70C-TX
POWER
LINKTEST UTILITY
1. LINK
2. FW
3. TEST
4. 5V LOCK
Panel Descriptions
1 TEST
Quick and easy test for cables when used
with the AT-HDR-EX-70C-RX. Use the
button to start the test and the LED to
determine pass or fail.
2 UTILITY
Connect a mini-USB to USB-A cable from
this port to a computer for updating and
testing. Rotate the dial to set the unit into
dierent modes.
3 POWER and LINK LEDs
The power LED will illuminate green when
receiving power. The link LED will glow
yellow when signal is being sent/received
between the transmitter and the receiver.
4 DC 48V
Connect the included power supply to this
port.
5 RS-232
Bidirectional control port, used for pass
through of commands to or from the
receiver.
6 IR
Connect a 3rd party controller to the IR IN
port or an IR emitter to the IR OUT port.
7 HDBaseT OUT
Connect an HDBaseT cable from this port
to the HDBaseT IN port on the receiver.
8 HDMI IN
Connect an HDMI cable from a source to
this port. e.g. HDR BluRay Player
5 6 7 84
321
Pin out will be determined by the
RS-232 cable and connect as
RX (receive), TX (transmit) and
(Ground).
A 3-pin captive screw connector for RS-232 has been included.
A 4-pin captive screw connector for IR has been included.
IR IN is connected by a ground and signal wire. Use
with 3rd party control systems.
IR OUT is connected by a ground and signal wire.
For easy termination, Atlona recommends using the 3
meter IR cable AT-IR-CS-TX.
RS-232
IR
GND RX
TX
GNDRX TX
IR IN IR OUT
GND
S
S
Installation Guide


Produkt Specifikationer

Mærke: Atlona
Kategori: Ikke kategoriseret
Model: AT-HDR-EX-70C-TX

Har du brug for hjælp?

Hvis du har brug for hjælp til Atlona AT-HDR-EX-70C-TX stil et spørgsmål nedenfor, og andre brugere vil svare dig